Door panel how do I remove real door panal?

most door pillar trim is placed under the trim edge for the pillar it should pull back and reveal the edge of the trim panel

remove screw on panal around handle that opens car. remove 2 screws underneath handle that pulls door closed. check around door panal edge for screws and if so remove them. Now remove panal by prying slightly around edges or panal as to pull the clips loose. Dont bother if some break,they can be easly replaced and dont cost much at all. I always use a still putty knife to help pry panal off. This insures you dont crack panal while pulling on it. Once thjis is dont you will have access to the switch...Simply replace it and place panal back on and HEY !! you did it..... hope this helps and if so Please leave rating on this post and good luck..

not really sure on that one but on most first you will need to remove screw around handle that opens the door that needs to be removed. also should be screws underneth handle that pulls door shut that you will have to remove and in some cases . check around edge of door panal for more screws and if found remove them also. once all screws are removed you will need to pry on door panal slightly because there are clips behind panal holding it on. in alot of cases the clips break when removing panal but dont worry the can be bought at your local auto parts store and are very easy to replace. I usually use something flat like a small stiff putty knife to help pry door panal lose. this helps insure that you dont break of crack the panal. after all clips are off simply unplug wire connections and door handle linkage and your done. .....hope this helps and good luck

You will have to pry on the door panel to get it off.
You also will break some of the white plastic (christmas trees) that hold panel on.
Plan on going to an auto body supply house (wholesale retailer) to get a box of 20 fasteners. They turn yellow and dry out and break.
There should be a few screws holding arm rest and door panel also.

As per the Haynes manual for your vehicle.
DOOR WINDOW GLASS-REMOVAL AND INSTALLATION:
1. Remove the door outer panal.
2. Lower the window glass.
3. remove the two nuts and one screw securing the glass.
4. Remove the glass by lifting it up carefully and rotating it inward.
5. Installation is reversal of removal.

DOOR OUTER PANAL-REMOVAL AND INSTALLATION:
1. Remove door trim panal.
2. Remove the outside mirror. Remove the foam block from the mirror opening.
3. Remove the outside door handle.
4. Open the door and pry thhe outer sealing strip out of the window glass opening.
5. remove the door panal screws.
6. Detach the front and rear of the outer panel, then lift it toward the rear to remove it.
7. Installation is the reverse of the removal procedure. Apply thread locking compound to the panel retaining screws.

OUTSIDE DOOR HANDLE-REMOVAL:
1. Pull handle out and puch the centers of the retaining pins through the pins, then remove them and detach handle. (These pins are located underneath the handle.

Hope this helps, let me know if you need any other help.

the clips are all around door. about 7 or 8 inches apart. on both sides and bottom. use a flat blade or similar to pop clips loose on panal. when clips are loosened, then roll down window and slide panal upward to remove. good luck!!

If you have power windows start by disconnecting your negative battery cable. Then you need to locate and remove the screws that hold your interior door handles in place (they may be hidden by snap in, or snap on clips). Once you remove the screws that hold the door handles, remove any wire connectors to the handles, if they're not power you will need a small hook (kinda like a knitting needle) to remove the window crank. A manual window crank is held in place by a clip on the base. Slide the hook behind the base and remove the clip. The door panel itself, is held on by snap in clips, and you will need a small pry bar to pull them from the door (try to get as close to, or directly under the clips to prevent them from tearing out of the door panel). Once the clips are removed from the door, pull the panel upward to remove it from the door.

Install in reverse.

I hope this helps you, and I wish you luck on your repair.

you need to take out the door panal and work from the inside of the panal. Open it from there.

there's a tool to do it . but if your real carefull you can do it without it. 1st remove all the screws on doors armrest , then side a flat head screw drive in between door and panal slide it around till you feel the plastic buttons then pry slowly, repeat till you get them all.

make sure to remove any screws or bolts and slide the panel up like when lifting someting and then remove the panel and unlpug any conectors behind the panel if necesary then put it bak the same way