Question about 1993 GMC Sierra K1500

1 Answer

Replacing lock solenoid - 1993 GMC Sierra K1500

Posted by billly rothenberger on

Ad

1 Answer

tim simpson

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 2 Answers

I have a 1994 chevy silverado 2wd with a 4L60E. the trans wont shift out of 1st. unless i do it manually. and the speedo stopped working at the same time. i hooked up a cd player yesterday would that have anything to do with any of the sensors?

Posted on Jan 13, 2014

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Holden cruze 2009 key stuck in the ignition won't go to off position , can't get it out of park .What is the problem ?


Is it shifter on the floor ?
Ignition Lock Cylinder Control Actuator
If the vehicle is equipped with a floor mounted console gear shifter, it has a ignition lock cylinder control actuator system in the steering column. The ignition lock cylinder control actuator's purpose is to prevent the ignition key from being turned to the OFF position when the transmission is in gear and the vehicle may still be moving. The column ignition lock system consists of a ignition lock cylinder control actuator , and a park position switch that is located in the A/T shift lock control switch. The ignition lock cylinder control actuator contains a pin that is spring loaded out to mechanically prevent the ignition key cylinder from being turned to the lock position when vehicle transmission is not in the Park position. If vehicle power is lost, and/or the transmission is not in the Park position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column.

GM had problems with these ! Has a TSB - technical service bulletin !
Automatic Transmission Shift Lock Control Description and Operation
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
• The automatic transmission shift lock solenoid (serviced as the automatic transmission shift lock actuator), as well as the body control module (BCM) and the engine control module (ECM). The shift lock solenoid is located within the floor shift control assembly with vehicles equipped with floor shift.
• The BCM controls the voltage to the shift lock control solenoid through the shift lock control solenoid controlled voltage circuit. The following conditions must be met before the BCM will remove voltage from the shift lock solenoid:
- The ignition is in the ON position.
- The engine control module (ECM) sends an input via GMLAN serial data to the BCM indicating the transmission is in the PARK position.
- The BCM determines the brake pedal is applied according the brake pedal position.
Since the shift lock control solenoid is permanently grounded, the BCM supplies voltage to the automatic transmission shift lock control solenoid, mechanically locking the shift lever in the PARK position as the solenoid energizes. When the brake pedal is applied, the BCM turns the control voltage output of the shift lock control solenoid OFF, de-energizing the shift lock control solenoid. The de-energized solenoid releases the mechanical lock allowing the driver to move the shift lever out of the PARK position. When the transmission is out of the PARK position, the shift lock control solenoid remains de-energized.
During remote start operation, the BCM will energize the shift lock control circuit, locking the shift lever in the PARK position.
Replaced shifter on a cobalt , broken plastic part inside , wouldn't press on micro switch to disengage ! Found replacement shifter at auto slavage yard .$20.00 US

Sep 03, 2016 | Holden Cars & Trucks

1 Answer

My 2003 GMC ENVOY won't shift out of park


Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid


?€¢
The automatic transmission shift lock control switch

With the ignition in the ON position, voltage is supplied to automatic transmission shift lock control switch. Voltage flows through the normally closed contacts of the automatic transmission shift lock control switch to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid is permanently grounded. This energizes the automatic transmission shift lock control solenoid causing the transmission shift lever to be physically locked in the PARK position. When the brake pedal is pressed the contacts in the automatic transmission shift lock control switch open, de-energizing the automatic transmission shift lock control solenoid. This allows the shift lever to be move out of the PARK position.
Shift Lever Does Not Move with Brake Pedal Depressed ?

2

  1. Turn ON the ignition.
  2. Press and hold the brake pedal.
  3. Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
Go to Testing for Intermittent Conditions and Poor Connections
Go to Step 3

3

  1. Turn OFF the ignition.
  2. Disconnect the automatic transmission shift lock control switch.
  3. Turn ON the ignition, with the engine OFF.
  4. Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
Go to Step 7
Go to Step 4

4

  1. Turn OFF the ignition.
  2. Leave the automatic transmission shift lock control switch disconnected.
  3. Connect a test lamp between the A/T shift lock control solenoid supply voltage circuit at the automatic transmission shift lock control solenoid and a good ground.
  4. Turn ON the ignition with the engine OFF.
Does the test lamp illuminate?

5

  1. Turn OFF the ignition.
  2. Connect a test lamp between the ignition 1 voltage circuit of the park lock solenoid and a good ground.
  3. Turn ON the ignition with the engine OFF.
Does the test lamp illuminate?
Go to Step 6
Go to Step 9

6

  1. Turn OFF the ignition.
  2. Connect a test lamp between the ignition 1 voltage circuit of the park lock solenoid and the park lock solenoid ground circuit.
  3. Turn ON the ignition with the engine OFF.
Does the test lamp illuminate?
Go to Step 8
Go to Step 11

7

Inspect for poor connections at the harness connector of the automatic transmission shift lock control switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
Go to Step 13

8

Inspect for poor connections at the harness connector of the park lock/automatic transmission shift lock control solenoid assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
Go to Step 12

9

Repair the open or high resistance in the park lock solenoid ignition 1 voltage circuit. Refer to Circuit Testing or Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 14
--

10

Repair short to battery positive voltage in the A/T shift lock control solenoid supply voltage circuit. Refer to Circuit Testing or Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 14
--

11

Repair the open or high resistance in the park lock solenoid ground circuit. Refer to Circuit Testing or Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 14
--

12

Important: Depress the button on the side of the shift lock actuator. With the button is depressed, cycle the plastic straw within the shift lever 3 to 5 times. The straw should move smoothly and freely except near the top of the travel where additional force will be required to mechanically actuate the park lock mechanism inside of the shift lock actuator. If there is stick/slip or abnormal friction while cycling the plastic straw or if the straw is altogether stuck in the lever, the entire control assembly (shifter and shift lock actuator) needs to be replaced. Refer to Transmission Control Replacement . If there is no abnormal friction, replace the shift lock actuator. Refer to Automatic Transmission Shift Lock Control Actuator Replacement .
Did you complete the replacement?
Go to Step 14
--

13

Replace the automatic transmission shift lock control switch. Refer to Stop Lamp Switch Replacement in Lighting Systems.
Did you complete the replacement?
Go to Step 14
--

14

Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Jul 09, 2016 | GMC Cars & Trucks

1 Answer

How do I get shifter out of park?


The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid


?€¢
The body control module (BCM)


?€¢
The powertrain control module (PCM)

The BCM controls the voltage to the shift lock control solenoid through the shift lock control solenoid controlled voltage circuit. The following conditions must be met before the BCM will supply voltage to the shift lock control solenoid:
?€¢
The ignition is in the ON position.


?€¢
The PCM sends a class 2 message to the BCM indicating the transmission is in the PARK position.


?€¢
The BCM determines the brake pedal is not applied according to the stop lamp switch.

When the ignition is in the ON position, the ignition 1 fuse supplies voltage to the automatic transmission shift lock control solenoid as the BCM supplies a ground to the control circuit, mechanically locking the shift lever in the PARK position as the solenoid energizes. When the brake pedal is applied, the BCM turns the ground of the control circuit OFF, de-energizing the shift lock control solenoid. The de-energized solenoid releases the mechanical lock allowing the driver to move the shift lever out of the PARK position. When the transmission is out of the PARK position, the shift lock control solenoid remains de-energized.
Your best bet is to take it to the dealer ,may have DTC'S
DTC B2707 Gearshift Unlock Circuit Low
The body control module (BCM) controls the automatic transmission shift lock control solenoid by providing a controlled ground to the automatic transmission shift lock control solenoid. The BCM utilizes a smart driver to monitor the voltage and current flow of the automatic transmission shift lock control solenoid control circuit. DTC B2707 will set when the BCM detects a short to ground when the solenoid is in the OFF state.
DTC B2708 Gearshift Unlock Circuit High
Did you perform the Diagnostic System Check - Vehicle?
Go to Step 2
Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

  1. Turn ON the ignition, with the engine OFF.
  2. Press and hold the brake pedal.
  3. Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 3

3

  1. Turn OFF the ignition.
  2. Install a scan tool.
  3. Turn ON the ignition, with the engine OFF.
  4. Press and hold the brake pedal.
  5. With a scan tool, command the Brake to Shift Relay output control parameter On.
  6. Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
Go to Step 4
Go to Step 6

4

  1. With the scan tool, observe the Brake Switch parameter in the powertrain control module (PCM) data display list.
  2. Press and release the brake pedal several times while observing the scan tool.
Does the brake input display Applied and Released with the brake pedal operation?
Go to Step 5
Go to Diagnostic Starting Point - Lighting Systems in Lighting Systems

5

With the scan tool observe the TR Sw. parameter in the body control module (BCM) data list.
Does the scan tool indicate PARK position?
Go to Step 9
Go to Scan Tool Data List in Engine Controls - 3.4L

6

  1. Turn OFF the ignition.
  2. Disconnect the harness connector of the automatic transmission shift lock control solenoid.
  3. Turn ON the ignition, with the engine OFF.
  4. Press and hold the brake pedal.
  5. Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
Go to Step 7
Go to Step 8

7

Test the controlled ground circuit of the automatic transmission shift lock control solenoid for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 12
Go to Step 9

8

Inspect for poor connections as the harness connector of the automatic transmission shift lock control solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 12
Go to Step 10

9

Inspect for poor connections at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 12
Go to Step 11

10

Replace the automatic transmission shift lock control solenoid. Refer to Shift Lock Control Solenoid Replacement .
Did you complete the replacement?
Go to Step 12
--

11

Replace the BCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup and programming.
Did you complete the replacement?
Go to Step 12
--

12

Operate the system in order to verify the repair.
Did you find and correct the condition?
System OK
Go to Step 3

Your best bet

Jan 11, 2016 | 2005 Chevrolet Equinox

1 Answer

Stuck in park will not shift


Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control is a safety device that prevents an inadvertent shift out of PARK when the ignition is ON. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid.


?€¢
The automatic transmission shift lock control switch.


?€¢
The park/neutral position switch.

With the ignition in the ON position, battery positive voltage is supplied to the park/neutral position switch. When the transmission is in the PARK position the contacts in the park/neutral position switch are closed. This allows current to flow through the switch to the automatic transmission shift lock control switch. The circuit continues through the normally-closed switch to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid is permanently grounded. This energizes the automatic transmission shift lock control solenoid, locking the shift linkage in the PARK position. When the driver presses the brake pedal the contacts in the automatic transmission shift lock control switch open, causing the automatic transmission shift lock control solenoid to release. This allows the shift lever to move from the PARK position.
Park Lock Solenoid
The park lock solenoid is a safety device that prevents an inadvertent shift out of PARK when the key is in the OFF position. The key must be in the RUN position to release the park lock solenoid. The system consists of the park lock solenoid. With the ignition in the ON position, voltage is supplied to the park lock solenoid. The park lock solenoid energizes through a permanent ground unlocking the shift lever. With the ignition in the OFF or ACCY position the park lock solenoid de-energizes and locks the shift lever in the park position.
Shift Lever Does Not Move with Brake Pedal Depressed
DEFINITION: Transmission shift lever will not move out of the PARK position with the ignition ON and the brake pedal pressed.

1

Did you perform the Symptoms - Automatic Transmission Shift Lock Control tests and all the necessary inspection?
Go to Step 2
Go to Symptoms - Automatic Transmission Shift Lock Control

2

  1. Turn ON the ignition, with the engine OFF.
  2. Press and hold the brake pedal.
  3. Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO Go to Step 3

3

  1. Turn OFF the ignition.
  2. Disconnect the automatic transmission shift lock control switch.
  3. Turn ON the ignition, with the engine OFF.
  4. Press and hold the brake pedal.
  5. Attempt to move the transmission shift lever out of the PARK position.
Does the transmission shift lever move out of the PARK position?
Go to Step 6
Go to Step 4

4

  1. Turn OFF the ignition.
  2. Disconnect the automatic transmission shift lock control solenoid.
  3. Turn ON the ignition, with the engine OFF
  4. Press and hold the brake pedal.
  5. Attempt to move the transmission shift lever out of the PARK position.
Does the transmission shift lever move out of the PARK position?
Go to Step 7
Go to Step 5
Inspect for poor connections at the harness connector of the automatic transmission shift lock control solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 10
Go to Step 9

6

Inspect for poor connections at the harness connector of the automatic transmission shift lock control switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 10
Go to Step 8

7

Repair the short to battery positive voltage in the A/T shift lock control solenoid supply voltage circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 10
--

8

Replace the automatic transmission shift lock control switch. Refer to Stop Lamp Switch Replacement in Lighting Systems.
Did you complete the replacement?

Oct 13, 2015 | 2006 Hummer H2

1 Answer

Driver door will not lock manually with key or with the remote


Lock solenoid in the door will freeze up sometimes. Remove the inner door panel and disconnect the solenoid. See if the key will work with it removed ind if so replace the solenoid

Sep 12, 2014 | Cars & Trucks

1 Answer

Power lock does not work on rear door


Power door lock mechanisms required periodic lubrication to work correctly. Without periodic lubrication, the mechanisms stick and, eventually, the lock solenoid will fail and require replacement. As a rule, the power lock mechanisms and power window regulators should be lubricated every two to three years.
Begin by removing the door panel and lubricating all points of the lock mechanism, including the solenoid plunger. If that does not correct the condition, look for broken parts and mechanical obstructions. Manually move the solenoid plunger to make sure that the mechanism is not seized. If the mechanism will not move, detach the mechanism from the actuator solenoid and see if the solenoid itself has seized.
Check that the lock solenoid is receiving 12V when the LOCK/UNLOCK button is actuated. If not, trace down the electrical fault. If the mechanism moves freely, and there is voltage at the connector when the switch is actuated, the solenoid has burned out and should be replaced.

Jul 23, 2014 | 2005 Dodge Caravan

1 Answer

My 2006 saab 97x shifter is locked in park but it says its in neutral. It starts fine and i am able to push the car. How do i get it off park


Shift interlock problem . do you know what that is ?
Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
• The automatic transmission shift lock control solenoid
• The automatic transmission shift lock control switch
With the ignition in the ON position, voltage is supplied to automatic transmission shift lock control switch. Voltage flows through the normally closed contacts of the automatic transmission shift lock control switch to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid is permanently grounded. This energizes the automatic transmission shift lock control solenoid causing the transmission shift lever to be physically locked in the PARK position. When the brake pedal is pressed the contacts in the automatic transmission shift lock control switch open, de-energizing the automatic transmission shift lock control solenoid. This allows the shift lever to be move out of the PARK position.
Park Lock Solenoid
The park lock solenoid is a safety device that prevents an inadvertent shift out of PARK when the key is in the OFF position. The key must be in the RUN position to release the park lock solenoid.
The system consists of the park lock solenoid.
With the ignition in the ON position, voltage is supplied to the park lock solenoid. The park lock solenoid energizes through a permanent ground unlocking the shift lever. With the ignition in the OFF or ACCY position the park lock solenoid de-energizes and locks the shift lever in the park position.

Shift Lever Does Not Move with Brake Pedal Depressed
Step
Action
Yes
No
Schematic Reference: Shift Lock Control Schematics
Connector End View Reference: Shift Lock Control Connector End Views or Automatic Transmission Related Connector End Views
DEFINITION: Transmission shift lever does not move out of the PARK position with the ignition ON and the brake pedal pressed.
1
Did you perform the symptom table tests and necessary inspections?
YES - Go to Step 2
NO - Go to Symptoms - Automatic Transmission Shift Lock Control
2
Turn ON the ignition.
Press and hold the brake pedal.
Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
YES - Go to Testing for Intermittent Conditions and Poor Connections
NO - Go to Step 3
3
Turn OFF the ignition.
Disconnect the automatic transmission shift lock control switch.
Turn ON the ignition, with the engine OFF.
Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
YES - Go to Step 7
NO - Go to Step 4
4
Turn OFF the ignition.
Leave the automatic transmission shift lock control switch disconnected.
Connect a test lamp between the A/T shift lock control solenoid supply voltage circuit at the automatic transmission shift lock control solenoid and a good ground.
Turn ON the ignition, with the engine OFF.
Does the test lamp illuminate?
YES - Go to Step 10
NO - Go to Step 5
5
Turn OFF the ignition.
Connect a test lamp between the ignition 1 voltage circuit of the park lock solenoid and a good ground.
Turn ON the ignition, with the engine OFF.
Does the test lamp illuminate?
YES - Go to Step 6
NO - Go to Step 9
6
Turn OFF the ignition.
Connect a test lamp between the ignition 1 voltage circuit of the park lock solenoid and the park lock solenoid ground circuit.
Turn ON the ignition, with the engine OFF.
Does the test lamp illuminate?
YES - Go to Step 8
NO - Go to Step 11
7
Inspect for poor connections at the harness connector of the automatic transmission shift lock control switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
YES - Go to Step 14
NO - Go to Step 13
8
Inspect for poor connections at the harness connector of the park lock/automatic transmission shift lock control solenoid assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
YES - Go to Step 14
NO - Go to Step 12
9
Repair the open or high resistance in the park lock solenoid ignition 1 voltage circuit. Refer to Circuit Testing or Wiring Repairs .
Did you complete the repair?
Go to Step 14
--
10
Repair short to battery positive voltage in the A/T shift lock control solenoid supply voltage circuit. Refer to Circuit Testing or Wiring Repairs .
Did you complete the repair?
Go to Step 14
--
11
Repair the open or high resistance in the park lock solenoid ground circuit. Refer to Circuit Testing or Wiring Repairs .
Did you complete the repair?
Go to Step 14
--
12
Important: Depress the button on the side of the shift lock actuator. With the button is depressed, cycle the plastic straw within the shift lever 3 to 5 times. The straw should move smoothly and freely except near the top of the travel where additional force will be required to mechanically actuate the park lock mechanism inside of the shift lock actuator. If there is stick/slip or abnormal friction while cycling the plastic straw or if the straw is altogether stuck in the lever, the entire control assembly (shifter and shift lock actuator) needs to be replaced. Refer to Transmission Control Replacement . If there is no abnormal friction, replace the shift lock actuator. Refer to Automatic Transmission Shift Lock Control Actuator Replacement .
Did you complete the replacement?
Go to Step 14
--
13
Replace the automatic transmission shift lock control switch. Refer to Stop Lamp Switch Replacement .
Did you complete the replacement?
Go to Step 14
--
14
Operate the system in order to verify the repair.
Did you correct the condition?
System OK

Apr 21, 2013 | Cars & Trucks

1 Answer

Suzuki Forenza 2008 Power Door Lock Not Working, I can press it but nothing happened.


if the fuse is good, it can only be 32 things.
the switch to lock it. or the wires to the lock solenoid or the solenoid.
you can find the cause 2 ways,
hotwiring it.
or using a voltmeter.
ill assume you never seen a VM.
jumper the switch, does it solenoid work now?
yes,bad switch,
jumper the solenoid,, work now?
yes, bad wires.
no, bad solenoid.
with meter you can trace the voltage to the solenoid and find the fail point in under 5min, door card off.
i just replaced my solenoid last week, $100 just for the silly part.
im a retired, mech. (electrics, specialist)

Mar 05, 2013 | Suzuki Forenza Cars & Trucks

1 Answer

1999 oldsmobile Alero Door Lock


sound like the bi directional solenoid. your power window has two of them . unlock solenoid lock solenoid .sound like the lock solenoid is bad or the relay or it could be a short.

Oct 08, 2008 | 1999 Oldsmobile Alero

1 Answer

2002 toyota celica power door lock problem


Are you hearing any noises from the pass door when you activate the lock switch? If not, the power door lock solenoid has failed, and prob needs to be replaced. Pull the door panel & check to see if it is getting power to the solenoid in lock & unlock. If it has power, the solenoid is def bad.

Jul 10, 2008 | 2002 Toyota Celica

Not finding what you are looking for?

Open Questions:

See all 1993 GMC Sierra K1500 Questions

Cars & Trucks Logo

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Ryan Lutton
Ryan Lutton

Level 3 Expert

1256 Answers

john h

Level 3 Expert

23515 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...