Question about 1996 Jeep Grand Cherokee

1 Answer

My transmisson makes a weezing sound when im at low speed

When im driving at low speed my transmission makes a wheezing sound and it idles high between 3 and 5 before shifting to 2nd or 3rd gear on my 1996 jeep grand Cherokee what could that problem be?

Posted by djbuddyfinch on

Ad

1 Answer

Richard Scordino

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

You sure its the transmission? Wheezing sound is usually the catylitic converter becoming plugged. Also...at 3-5K rpm you are not idling, you are reving the engine...(in that case, trans may be slipping or flairing between shifts, unless the unit is staying in one gear and just delaying shift till you reach that rpm. actual shift point should be close to 2,000rpm) I'd check the cat first.

Posted on Apr 17, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does it mean when my 96 Lincoln Continental won't shift from 2nd to 3rd gear and is it safe to drive it like that?


It is safe to drive but the car is running in too low a gear at high speed and this will result in greater engine wear and lower gas mileage.

You have a transmission problem.

Apr 01, 2016 | Lincoln Cars & Trucks

1 Answer

3 speed box in drive 1st and 2nd gear takes 3rd gear dont


How to adjust 3 speed column shifter - YouTube

? 9:53
https://www.youtube.com/watch?v=2TCHzIvAvRQ
Mar 6, 2014 - Uploaded by luke Fugate
This is a video to show you how to adjust a Three speed on the column to ... It's great not having to wind the engine and transmission just to take off in 2nd or 3rd gear. ... It was ALWAYS getting stuck between 1st and 2nd gear. .... 1977 c10 3 On The Tree ' How to Drive a 3 Speed Column Shift - Duration: ...

Diagnose Automatic Transmission

www.aa1car.com/library/2002/bf90222.htm
All they know is that they put their gear selector in "D" for Drive and their vehicle ... But when internal problems cause the transmission to act up, it takes a fair amount .... In Chrysler three-speed automatics, changing the fluid to ATF+3 can also help ...kickdowns to get the transmission to downshift to 1st from 2nd or 3rd gear.

Manual transmission - Wikipedia, the free encyclopedia

https://en.wikipedia.org/wiki/Manual_transmission

Wikipedia1 Overview; 2 Unsynchronized transmission; 3 Synchronized transmission; 4 Internals.... gear speeds by blipping the throttle when shifting from 2nd into 1st. ... In a synchromesh gearbox, to correctly match the speed of the gear to that of the ... Even in transmissions that do not feature direct drive, it's an advantage for the ...

When do you use the 1,2,3 gears on an automatic car ...

https://www.reddit.com/.../when_do_you_use_the_123_gears_on_..

Jan 10, 2016 | Cars & Trucks

1 Answer

How to fix ram 1500 2005 transmission that sometimes gets stuck in 3rd gear. from start to finish truck will stay in 3rd gear.


When did you last replace trans filter and fluid? Dirt may be causing shift valve to stick.

Dec 28, 2014 | 2005 Dodge Ram 1500

1 Answer

I have a 1998 dodge Grand Caravan with codes P0700,P0734 & P0733. What does this mean?


P0700 is a informative transmission code, about some problem there; the P0733 and P0734 is the specific problem there.
I would first try changing the fluid and filter. Although the fluid may look like it is brand new, with 100K on the fluid, I can assure you that even if those miles were all highway at steady speed and no load that the fluid has deteriorated and no longer lubricating the internal parts properly and that there is some debris in the ******.If codes return and shifting problems are still present, there is definite internal failure, possibly the pump or in the clutches.
DTC P0733The powertrain control module (PCM) uses the crankshaft position (CKP) sensor, input speed sensor (ISS) and output speed sensor (OSS) to determine engine speed, input shaft speed and output shaft speed. These sensor readings are used to determine the current gear ratio and RPM slip across the torque converter. The PCM uses this information from the sensors to determine if the commanded gear matches the actual gear. During normal driving conditions, the PCM will adapt main line pressure via the pressure control (PC) solenoid to prevent slipping and harsh shifts. Shift solenoid 3 is used to apply or release third gear clutch. The PCM controls 3rd gear by controlling the ground for shift solenoid 3. The PCM will turn the solenoid OFF, open the driver circuit, when 3rd gear is commanded On to apply 3rd clutch. Shift solenoid 3 is supplied ignition voltage from the fuel pump relay whenever the PCM commands the fuel pump relay ON. DTC P0733 sets when 3rd clutch still slips after the PCM has commanded high main line pressure.DTC Parameters
DTC P0733 will set if the PCM detects an incorrect actual 3rd gear ratio when 3rd gear is commanded On when:- The condition exists for longer than 3 seconds (2001)*- The condition exists for longer than 3 seconds, 1 minute is allowed to elapse, then condition exists again for longer than 3 seconds (2000)- The high main line pressure has been commanded- The transaxle is in a forward gear- The input speed is greater than 224 RPM- The vehicle speed is greater than 5 km/h (3 mph)- The speed noise parameter = NO- The steady state ratio fail counter equals 255 for an in-gear failure, or the shift fail counter is greater than 100 on a downshift or upshift to 3rd gear (128=0 or normal operation)DTC P0733 diagnostic runs continuously once the above conditions have been met.
DTC P0733 is a type A DTC for 2000, type B for 2001.**Applicable to vehicles built after June 2000.
Diagnostic AidsImportant: If DTCs P0745, P0746, P0756, P0758, P0761, P0763, P0766, P0768 or P0789 is set, diagnose that DTC first. A diagnosed PC solenoid, shift solenoid 2, 3 or 4 low/high circuit fault DTC may have caused DTC P0733 to set.Important: If a shift solenoid performance DTC P0783, 4th gear stuck ON, is set, diagnose that DTC first. A 4th gear stuck ON may cause no 3rd gear, no 2nd gear, or TCC stuck Off.
Refer to Pressure Ports - Air Check and Parts Description for pressure apply points and for component/location description.
Possible causes of no 3rd gear are listed in the flowchart on the succeeding page.
Verify TRANSMISSION ISS and TRANSMISSION OSS read correctly on Scan tool.
Make sure the pressure control, shift 2, shift 3 and shift 4 solenoids are not intermittently sticking. A sticking shift solenoid 4 may cause 4th gear to be applied from an initial start resulting in no 3rd gear. Audible sound should be similar for all solenoids. A muffled tone indicates the need for replacement.
Check this pinout HERE
P0734 refer at ratio 4 gear, and the rocedure is the same.
Hope helps.

Jan 22, 2013 | 2003 Dodge Caravan

1 Answer

Codes p0700,p0733,p0734 dodge caravan 1997


P0700 is a informative transmission code, about some problem there; the P0733 and P0734 is the specific problem there.
I would first try changing the fluid and filter. Although the fluid may look like it is brand new, with 100K on the fluid, I can assure you that even if those miles were all highway at steady speed and no load that the fluid has deteriorated and no longer lubricating the internal parts properly and that there is some debris in the ******.If codes return and shifting problems are still present, there is definite internal failure, possibly the pump or in the clutches.
DTC P0733The powertrain control module (PCM) uses the crankshaft position (CKP) sensor, input speed sensor (ISS) and output speed sensor (OSS) to determine engine speed, input shaft speed and output shaft speed. These sensor readings are used to determine the current gear ratio and RPM slip across the torque converter. The PCM uses this information from the sensors to determine if the commanded gear matches the actual gear. During normal driving conditions, the PCM will adapt main line pressure via the pressure control (PC) solenoid to prevent slipping and harsh shifts. Shift solenoid 3 is used to apply or release third gear clutch. The PCM controls 3rd gear by controlling the ground for shift solenoid 3. The PCM will turn the solenoid OFF, open the driver circuit, when 3rd gear is commanded On to apply 3rd clutch. Shift solenoid 3 is supplied ignition voltage from the fuel pump relay whenever the PCM commands the fuel pump relay ON. DTC P0733 sets when 3rd clutch still slips after the PCM has commanded high main line pressure.DTC Parameters
DTC P0733 will set if the PCM detects an incorrect actual 3rd gear ratio when 3rd gear is commanded On when:- The condition exists for longer than 3 seconds (2001)*- The condition exists for longer than 3 seconds, 1 minute is allowed to elapse, then condition exists again for longer than 3 seconds (2000)- The high main line pressure has been commanded- The transaxle is in a forward gear- The input speed is greater than 224 RPM- The vehicle speed is greater than 5 km/h (3 mph)- The speed noise parameter = NO- The steady state ratio fail counter equals 255 for an in-gear failure, or the shift fail counter is greater than 100 on a downshift or upshift to 3rd gear (128=0 or normal operation)DTC P0733 diagnostic runs continuously once the above conditions have been met.
DTC P0733 is a type A DTC for 2000, type B for 2001.**Applicable to vehicles built after June 2000.
Diagnostic AidsImportant: If DTCs P0745, P0746, P0756, P0758, P0761, P0763, P0766, P0768 or P0789 is set, diagnose that DTC first. A diagnosed PC solenoid, shift solenoid 2, 3 or 4 low/high circuit fault DTC may have caused DTC P0733 to set.Important: If a shift solenoid performance DTC P0783, 4th gear stuck ON, is set, diagnose that DTC first. A 4th gear stuck ON may cause no 3rd gear, no 2nd gear, or TCC stuck Off.
Refer to Pressure Ports - Air Check and Parts Description for pressure apply points and for component/location description.
Possible causes of no 3rd gear are listed in the flowchart on the succeeding page.
Verify TRANSMISSION ISS and TRANSMISSION OSS read correctly on Scan tool.
Make sure the pressure control, shift 2, shift 3 and shift 4 solenoids are not intermittently sticking. A sticking shift solenoid 4 may cause 4th gear to be applied from an initial start resulting in no 3rd gear. Audible sound should be similar for all solenoids. A muffled tone indicates the need for replacement.
Check this pinout HERE
P0734 refer at ratio 4 gear, and the rocedure is the same.
Hope helps.

Apr 03, 2012 | 2003 Ford Focus

1 Answer

1996 f150 4x4 e4od automatic stuck in 2nd or limp mode while in 2wheel drive or 4wheel high,when i put it in 4wheel low the transmission shifts in all gears. At fist I was told the transmission was bad,so...


Wow,
That's odd ,push button shift I suppose . Ford doesn't have a 2nd gear limp mode ,I don't think.
Has to be the manual linkage at the shifter,try manually shifting? still no low?

Oct 10, 2011 | 1996 Ford F150 Regular Cab

1 Answer

1996 2500 diesel auto transmisssion, auto shifting while on road


sounds like trans has gone bad, last service of filter and fluid? clogged screen or low/burnt fluid would effest but if clunking sounds like trans is shot

Jul 06, 2009 | 1996 Dodge Ram 2500 Club Cab

1 Answer

When i shift from 1st to 2nd it either is popping back into neutral or its not actually going in to second im not sure when i try to shift it again it goes into 2nd and doesn't pop back out. it seems to be...


Car need to be taken to a transmission service shop.
If you keep driving it the way it is,,you could break the gear altogether,this will add to your repair bill.
Right now,,it could be just an adjustment.

Jan 19, 2009 | Chevrolet Camaro Cars & Trucks

1 Answer

96 caprice classic not shifing from 2nd to 3rd


check transmission fluid level first if it is full or if it is milky looking or smell cooked change the fluid and filter because the screen in the filter maybe plugged and not allowing the fluid to go to the troque converter

Dec 25, 2008 | 1996 Chevrolet Caprice Classic

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

372 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...