Question about 2000 Dodge Caravan

1 Answer

2007 chrysler town and country transmission slips from 1st to 2nd and won't shift into high gear at all. Error codes are P00073 and P00071

Posted by demian keen on

Ad

1 Answer

George Metz

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Is this the 3.5 liter engine?

Posted on Aug 19, 2013

Testimonial: "no it is a 3.8 liter"

Ad

3 Related Answers

SOURCE: 94 dodge neon auto tranny

Hi,

Here is some possible reasons why your transmission is having those problems .

* The gear shift linkage is binding
* There is an internal problem in the transmission
* The throttle cable is broken or disconnected
* The vacuum modulator on the transmission is faulty or the vacuum line is damaged
* The electronic transmission control circuit may be faulty

Posted on Feb 26, 2009

Ad

Anonymous

  • 1 Answer

SOURCE: Transmission won't shift from 1st to 2nd gear on it's own

Have someone scan the transmission for bad shift sensors.

Posted on Apr 28, 2009

super_guy

  • 1986 Answers

SOURCE: Chrysler town country 1996 headlight

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Nov 04, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why my 2001 town & country 3.8 will not shift gears?


p1784 shift up /down wire open,,,P0700 Transmission Control System Malfunction

Read more at: http://www.obd-codes.com/trouble_codes/
Copyright © OBD-Codes.com

P0732 Gear 2 Incorrect ratio

Read more at: http://www.obd-codes.com/trouble_codes/
Copyright © OBD-Codes.com

Apr 23, 2015 | 2001 Chrysler Town & Country

1 Answer

Transmission won't shift into high gear.


are there any codes? Does it shift ok in 1st and 2nd? sounds like your over drive shift solenoid or your 3 and 4 shift solenoid is stuck and needs to be replaced

Jan 02, 2013 | 1997 Chevrolet Blazer

1 Answer

2003 Chryser Town and country - First to send gear bump, bump grab.


Then you have an internal transmission failure from poor workmanship on the rebuild.

Oct 28, 2012 | 2003 Chrysler Town & Country

1 Answer

****** studders from 1st to 2nd gear


Transmission should be serviced with new filter and oil every 50k or so. If you missed the one at 50k, and by the dark fluid I'm guessing you did not do it at 100k, you likely need a new transmission.

Apr 17, 2012 | 2003 Chrysler Town & Country

1 Answer

My tranny have error P0733 town&country 2001 after repair automatic transmission


P0733 indicates which gear has a gear ratio that varies from the correct gear ratio, the corresponding in-gear trouble code ranges from DTCs P0731-36.

Without taking apart the transmission and inspecting for damage, it is difficult to say what the exact problem is, but many people who get the P0733 code have fixed the problem by replacing the accumulator in the transmission.

Other possible causes include:
  • ATF level low
  • Deteriorated ATF
  • Shift solenoid B or F malfunction
  • Pressure control solenoid malfunction
  • Line pressure low
  • Low clutch slipping
  • High clutch slipping
  • Control valve malfunction
  • Oil pump malfunction
  • TCM malfunction


I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

Feb 08, 2011 | 2001 Chrysler Town & Country

1 Answer

I notice that sometimes my 98 chrysler town an country jumps from 1st gear to 2nd gear to soon. Does that mean that my transmission is starting to go out?


If it is only happening sometimes, you should get your transmission serviced ASAP. If you do this you should be able to save the transmission.

May 19, 2010 | 1999 Chrysler Town & Country

1 Answer

Country speedometer doesn't work and won't shift out of 1st gear


transmission speed sensor needs replacing about 40.oo$ at the dealer sits on the right side of transmission looking from the front of the radiator g s.

Apr 17, 2009 | 2001 Chrysler Town & Country

1 Answer

Transmission with codes P0218 P0732 P0733 P0740 P0846 P1790


I agree, this is a lot of codes. I would tend to think this would be electrical, perhaps computer are a loose connection? These trannys I have rebuilt so far usually have a couple of codes related to the problem but not this many - all over the place.

Apr 16, 2009 | Chrysler Town and Country Cars & Trucks

1 Answer

01 Chrysler T&C Transmission Problem 3.3L engine


try having the transmission module re-flashed.

Mar 14, 2009 | 2001 Chrysler Town & Country

Not finding what you are looking for?
2000 Dodge Caravan Logo

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

Mike

Level 3 Expert

4372 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...