Question about 1999 Dodge Durango

1 Answer

Need to the torque specs for a 1999 Dodge Durango

I need to torque specs for the head bolts and the intake on a 1999 Dodge Durango with a 318. Thank you!!

Posted by twinklingsta on

  • 3 more comments 
  • twinklingsta Apr 08, 2009

    Thank you very much!

  • Anonymous Mar 15, 2014

    whats the torque specs for the cylinder head on a 2000 focus 2.0

  • Anonymous Mar 15, 2014

    whats the torque specs for the cylinder head on a 2000 focus 2.0

  • Anonymous Mar 20, 2014

    need the torque of the bolts

  • Anonymous Mar 28, 2014

    just need torque pattern and specs

×

Ad

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 69 Answers

Head Torque sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs recheck final torque in sequence.

Torque intake manifold: Step 1: 12 inch/Lbs, (hand tight) Step 2: 72 inch/Lbs, (6) Ft/Lbs Step 3: 12 Ft/Lbs
torque intake plenum: Step 1: 24 inch/lb (hand tight) Step 2: 48 inch/lb (4) Ft/Lbs Step 3: 84 inch/lb (7) Ft/Lbs (To torque bolts, start in center using crisscross pattern)

Posted on Apr 07, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

03 Dodge Intrepid intake manifold torque specs top & bottom is for 3.5 V6


Lower Intake:
  1. Use a skin coat of RTV silicone on both sides of the water passage ports (outer most holes) and put the new lower intake gaskets into place
  2. Hand tighten the 13mm head intake bolts and Torque the bolts , starting from the center and working your way out in a circular pattern
  3. Torque these bolts in a few small increments until they have reached 250 inch pounds of torque.
  4. Upper Intake Plenum:
  5. When installing the intake air plenum , be sure to catch the four center bolts and the two side bolts (stiffener brackets) before tightening , The center bolts should be torqued to 250 inch pounds .The fuel rail bolts should be torqued to 100 inch pounds

Jun 24, 2016 | 2003 Dodge Intrepid

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter


Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif

Dec 10, 2015 | Dodge Cars & Trucks

1 Answer

What are the torque specs and sequence for the intake and head gasket on a 1999 Chevy Silverado 6.0l V8 K2500


Cylinder Head Bolts (First Pass all M11 Bolts in Sequence)
30 N?·m
22 lb ft
Cylinder Head Bolts (Second Pass all M11 Bolts in Sequence)
90 degrees
Cylinder Head Bolts (Final Pass all M11 Bolts in Sequence-Excluding the Medium Length Bolts at the Front and Rear of Each Cylinder Head)
90 degrees
Cylinder Head Bolts (Final Pass M11 Medium Length Bolts at the Front and Rear of Each Cylinder Head in Sequence)
50 degrees
Cylinder Head Bolts (M8 Inner Bolts in Sequence)
30 N?·m
22 lb ft
Intake Manifold Bolts (First Pass in Sequence)
5 N?·m
44 lb in
Intake Manifold Bolts (Final Pass in Sequence)
10 N?·m
89 lb in
Intake Manifold Wiring Harness Stud
10 N?·m
89 lb in

Oct 27, 2015 | Cars & Trucks

1 Answer

2008 dodge charger with a 2.7 liter engine head boly specs


  1. 2.7 litre intake bolt torque spec in a 2008 dodge charger ...

    www.fixya.com/cars/t18664111-2_7_litre_intake_bolt_torque_spec_in Jun 27, 2013 - Head Bolts Step one 37 ft lbs then tignten 120 degrees more. Rocker arms. Step one 11 ft lbs then tighten 90 degresss more. Upper intake 89 inch ...

Feb 28, 2015 | 2008 Dodge Charger

3 Answers

Need head bolt, intake manifold, and exhaust torque specs


Cylinder Head Bolt Step1- (25 FT.Lbs) Step2(45 Ft.Lbs) Step3(65Ft,Lbs).....Intake Manifold(35Ft Lbs)....Exhaust Manifold Center (20Ft Lbs) All Others (20 Ftlbs).....Thanks

Mar 06, 2010 | GMC Suburban Cars & Trucks

1 Answer

Head bolt torque specs for 2000 dodge neon 2.0 SOHC


I have the specs and diagrams. If you want me to send them to you, give me your email address. [email protected]

Sep 01, 2009 | 1998 Dodge Neon

2 Answers

Need torque settings for 99 dodge durango head bolts & intake bo


Here's a link to a conversion calculator,www.unitconversion.org/energy/inch-pounds-to-foot-pounds-conversion.html

May 01, 2009 | 1999 Dodge Durango

1 Answer

Putting in new head gaskets, need all of the specs, timing ,


I googled the specs and i found mine it will give numbers and pictures. Sorry i couldn't actuall y give u the answer.

Mar 25, 2009 | 1999 Dodge Ram 2500 4WD

Not finding what you are looking for?
1999 Dodge Durango Logo

2,366 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...