Question about 2005 Mitsubishi Endeavor

1 Answer

Mitsubishi endeavor idle air control valve - 2005 Mitsubishi Endeavor

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 49 Answers

The idle air control is attached to the throttle body, located between the air cleaner and the intake manifold, and held on with 2 or 3 small screws. You should clean this, and the throttle body with carb cleaner while it is apart and try to resurrect.
Cheers
Dean

Posted on Feb 14, 2020

Ad

3 Suggested Answers

uortegon

  • 3 Answers

SOURCE: Cabin Air Filter - 2004 Mitsubishi Endeavor (Where?)

IT IS IN BEHIND THE GLOVE COMPARTMENT YOU HAVE TO TAKE IT OUT BY UNSREWING AND START FROM YOUR RIGHT SIDE

Posted on Jun 10, 2009

Ad

Anonymous

  • 53 Answers

SOURCE: need to know where the Idle Air control valve is

i have a 1997 what is the motor size like 2 liter? it should be on the t/b closes to the fire wall.

Posted on Mar 16, 2010

Jon Lobo

  • 14 Answers

SOURCE: Have a 1996 Mitsubishi Galant

You'll have to remove the throttle body to replace the idle air control (IAC) valve. First, disconnect the negative ground cable from the battery. Then remove the vacuum line and air duct intake. Then disconnect the IAC and throttle position sensor (TPS) electrical connections. Remove the coolant hoses that are connected to the IAC. Disconnect the throttle cable from the throttle body. Now, remove the 4 bolts that hold the throttle body to the manifold and remove. Be careful with the gasket located between the throttle body and manifold and replace it in the same position. On your clean work surface, turn the throttle body over and remove the 4 phillips head screws holding the IAC to the throttle body. Clean the parts with a dry cloth but do not use solvents on the IAC or TPS. That's it!

Posted on Dec 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 mitsubishi endeavor xls. Cranks but you have to press gas pedal for car to start, then it will not idle car will dies out


If the vehicle will stay running with the gas pedal slightly pressed, its most likely a problem with getting the correct volume of air into the engine at idle.

Mitsubishi parts look up doesn't show an idle air control valve. It looks like the throttle body is electronically controlled (no throttle cable or idle air control valve)

I would try cleaning the throttle body.

Mitsubishi Endeavor LS How to clean throttle body can

Apr 08, 2018 | Mitsubishi Cars & Trucks

1 Answer

I have a Mitsubishi Endeavor 2007 that has a low rpm when idling


Have the electronic engine control system run through an active test to see if the computer senses any issues with the engine running mode. This test needs to be done with a high end scanner that can run what we call a "Key On Engine Running" (KOER) self test.

Jan 14, 2017 | 2007 Mitsubishi Endeavor

1 Answer

If it has one,where is the idle air control valve loacation on a 2006 MITSUBISHI ENDEAVOR ?


motor should be a 3.8 L 6G75 SOHC 24v V6

same motor as 2006 pajero
yes it has one
inlet inlet manifold
look for this part and wiring connection

26354017-k55xxgxmar0fhwusosrhrquj-1-0.jpg

Nov 13, 2016 | Mitsubishi Cars & Trucks

1 Answer

My 2008 mitsubishi endevor stalls when driving


The very first thing that you need to do is have the engine control computers fault codes checked. The idle speed is 100% computer controlled.

Jul 17, 2016 | 2008 Mitsubishi Endeavor

1 Answer

2005 endeavor check light came on...ran scan and code p506 idle control system rpm low came up...any common solutions?


What does the tachometer read when you are at idle? the idle speed may need to be adjusted, it should be around 800

Jun 11, 2011 | 2005 Mitsubishi Endeavor

1 Answer

2005 Mitsu Endeavor p0506 Idle Air control.


Idle air control is not a sensor on the air horn.Why do people who have no clue bother answering? The idle speed is controled by the throttle body which allows a specific amount of air to flow into the engine thus controlling your idle speed. In this application it is an integral aspect of your throttle body. Check your throttle body for contamination. Check your wire harness connecters.

May 28, 2010 | 2004 Mitsubishi Endeavor

2 Answers

Endeavor burns a ton of oil...


These engines have been known for faulty cam seals (eg. Montero, Montero Sport (Nativa), Endeavor). You might not see oil on the ground because it gets burned up by the exhaust. Check that first.

Oct 09, 2009 | 2005 Mitsubishi Endeavor

1 Answer

Cabin Air Filter - 2004 Mitsubishi Endeavor (Where?)


IT IS IN BEHIND THE GLOVE COMPARTMENT YOU HAVE TO TAKE IT OUT BY UNSREWING AND START FROM YOUR RIGHT SIDE

May 31, 2009 | 2004 Mitsubishi Endeavor

Not finding what you are looking for?
2005 Mitsubishi Endeavor Logo

Related Topics:

520 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...