1999 Lincoln Town Car Logo
Posted on Apr 07, 2009
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

1999 lincoln con

~have remote keyless do not there a slide button on back like to know how to use it for my seats i think it is memory

  • randallm1 May 17, 2009

    dome lights keep blowing fuses

×

2 Answers

gerry bissi

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Lincoln Master 4,390 Answers
  • Posted on Apr 16, 2009
gerry bissi
Lincoln Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Jan 07, 2009
Answers
4390
Questions
1
Helped
3058542
Points
11499

SECTION 501-14B: Keyless Entry/Computer Operated Locks 1999 Town Car Workshop Manual GENERAL PROCEDURES Programming —Keyless Entry Keypad Code

  1. Enter the permanent factory keyless entry keypad code.
  1. Press the 1/2 button within five seconds to activate the programming mode. Holding the 1/2 button for more than two seconds will erase all stored customer codes. The existing codes do not need to be erased to program new codes.
  1. Enter the new five-digit keyless entry keypad code.
  1. To associate the new code with personality positions 1, 2 or 3, press the 1/2 button within 5 seconds of entering the 5th digit of the new code for position 1 or 3/4 button for position 2 or 5/6 for position 3. The door locks will lock and unlock confirming the new code is programmed.
  1. If another code is to be programmed, begin entering the code within 5 seconds of the last button pressed.
  1. After all new keyless entry codes are programmed:
    • Press keyless entry keypad buttons 7/8 and 9/0 at the same time to exit the program mode.
    • Wait for 5 seconds; the driver door module (DDM) will exit the program mode automatically.
    • -------------------------------------------------------------
Programming —Transmitter
  1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming program mode has been entered.
  1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
    Press any button on the transmitter to be programmed.
  1. If additional keyless entry remote transmitters are to be programmed, repeat step 2 within 7.5 seconds.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
--------------------------------------------------
Programming —Remote Memory Activation NOTE: This procedure must be completed within 5 seconds.
  1. Press the SET button on the driver door panel.
  1. Press any button on the keyless entry remote transmitter to be associated with a memory setting.
  1. Press the 1 or 2 memory button on the driver door panel.
-------------------------------------------------------------
Programming —Autolock and Horn Chirp
  1. NOTE: This procedure must be completed within 30 seconds.
    Turn the ignition switch to RUN.
  1. Press the UNLOCK button three times.
  1. Turn the ignition switch to OFF.
  1. Press the UNLOCK button three times.
  1. Turn the ignition switch to RUN. The doors will lock and unlock to confirm entry into program mode.
  1. Press the UNLOCK button once to toggle the Autolock feature on or off, or twice to toggle the Horn Chirp function on or off. The horn will chirp to confirm toggling of the Autolock feature.
  1. Exit program mode by turning the ignition to OFF, START, or wait 7.5 seconds.
----------------------------------------------------------------------------------

Steve French

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

  • Contributor 1 Answer
  • Posted on Aug 14, 2015
Steve French
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Joined: Aug 14, 2015
Answers
1
Questions
0
Helped
1070
Points
4

None of this works. You all just copy each other's answers, all bullshyte

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

How Do I Know If My Car Equipped With A Keyless Entry Remote System? I have a 1999 Ford Windstar. I bought several remotes but can't get my locks to engage. Any help would be appreciated.

Hello Cathy

It does indeed have keyless entry. It needs reprogramming when you get a new remote. Also if you disconnect the battery. Usually a local car alarm fitting shop, or an auto-electrician will do it. Plus of course a Ford dealership.

https://www.google.com/search?q=Keyless+Entry+Remote+System+1999+Ford+Windstar

..
0helpful
1answer

Can I use a 4button keyless remote to replace a 3 button keyless remote

Hi,
Is the 3-button remote from Mazda too? If it is and it's from the same year range as your MPV it may work. In other words, many car makers used the same type of keyless remotes on all their vehicles in a given year range. But if the 3-button is much newer or older you're probably out of luck. You can search on Ebay to see what types of remotes were sold for your year car.

If this is NOT a Mazda remote and neither was the 4 button they may use a different frequency (think 'radio station') and won't 'talk' to the car's keyless remote compuer.

TD
1helpful
1answer

How do you program the transmitter on a 1996 Lincoln Town Car?

1. Enter 5-digit permanent entry code into the keyless entry keypad.
2. Within 5 seconds of pressing last button of code, press the 1/2 button. All doors will lock then
unlock confirming you are in programming mode.

3. Press any button on first Keyless Remote within 5 seconds of pressing the 1/2 button. Locks will
cycle to indicate succesful programming.

4. If you are programming more than one Keyless Remote (Including any exsiting remotes) Press
any button on second keyless remote within 5 seconds of previous remote. Locks will cycle again
to indicate succesfull programming. (If the keypad light goes out before all remotes are
programmed the entire process must be repeated).

5. Press the 7/8 and the 9/0 buttons simultaneously on the keypad to exit program mode.
0helpful
1answer

Reset memory on mirror on 1999 town car

Press the set button for the seat for 3 or 4 seconds. Move your mirrors into place, then press the the button for the seat position you are setting the mirrors for 1 or 2. The seats and mirrors are set at the same time.
0helpful
3answers

LHJ001 WIRING

I have the 1995-97 Lincoln Continental Alarm, Remote Starter, Keyless Entry Wiring, review it:

b94b6e9.png


Hope helped.
2helpful
1answer

Keypad door lock does not work..?

it's in owner manual. But, first you have to enter your original code and it must work. then you press the 1 button and then enter a new 5 digit code, then press the 1 button again.

Keyless Entry Keypad To unlock the driver front door (20124) , and disarm the anti-theft alarm control (19A366) , (if equipped):
  • Enter the permanent factory code.
  • Enter the owner's alternate code.
To unlock the passenger door(s), press the 3/4 button within five seconds of unlocking the driver door or luggage compartment. To unlock the luggage compartment door (40110), press the 5/6 button within five seconds of unlocking driver or passenger door(s). To turn on the courtesy lamps and light all illuminated components, lift either front door handle (22404) or press any button on the keyless entry keypad (14A626) . To lock all doors, press the 7/8 and 9/0 buttons at the same time with all doors closed. (It is not necessary to enter the key code first.) This will turn off courtesy lamps and arm anti-theft alarm control (if equipped). To program an alternate code:
  1. Enter the five digit permanent entry code into keyless entry keypad .
  1. Within five seconds of pressing last button of permanent code, press the 1/2 button within five seconds of pressing the last button of the permanent code.
  1. Enter any alternate five digit code within five seconds of pressing 1/2 button.
    • Enter a sixth digit as follows to indicate operator's memory seat setting to be set by alternate code:
      • 9/0 — no memory recall
      • 1/2 — memory seat position 1
      • 3/4 — memory seat position 2
      • 5/6 — memory seat position 3
    • After successful programming, the doors will signal by locking and then unlocking.
---------------------------------------------
  • Keyless Entry Keypad Does Not Work Properly
  • Circuit.
  • Keyless entry keypad.
  • Electronic door lock control processor.

  • Open Fuses:
    • Town Car and Crown Victoria/Grand Marquis
    • Power Distribution Box (under hood)- K, 40A (Maxi)
    • Instrument Panel Fuse Panel - 17 (10A), 10 (20A), 8 (15A), 5 (15A) and 4 (10A)
  • Loose Connectors
  • Corroded Connectors
  • 17helpful
    1answer

    How to change keyless entry code when I don't know the current

    Open the right/rear door. Pull the rubber weatherstrip back from the door opening. Fold the right/rear seat back down into a locked position, in order to access to the right/rear trim panel. Carefully, pry the right/rear upper trim panel housing the right/rear seat belt height adjuster. Now carefully pry back the lower trim panel taking care now to break it, exposing the vehicle security module with three connectors plugged into it, coloured green, blue, and grey. Look on the label that has the part number which should end in EB. There are FIVE numbers to the right of that number. Those five numbers are your keyless entry keypad code.
    0helpful
    1answer

    How do you reprogram the keyless door lock code?

    1. Enter the five digit permanent entry code into keyless entry keypad.
    2. Within five seconds of pressing last button of permanent code, press the 1/2 button within five seconds of pressing the last button of the permanent code. (Factory code found on the module).
    3. Enter any alternate five digit code within five seconds of pressing 1/2 button.
      • Enter a sixth digit as follows to indicate operator's memory seat setting to be set by alternate code: 9/0-- no memory recall
        1/2-- memory seat position 1
        314-- memory seat position 2
        5/6-- memory seat position 3
      • After successful programming, the doors will signal by locking and then unlocking.

    The Keyless Entry Module is located inside the drivers side door.
    3helpful
    2answers

    Need help programing two keyless entry remotes

    Enter the keyless entry code on the door keypad 3 times. Locks will cycle down and up after the third time. Press and release the "lock" button. Locks should cycle again. May need to hold down lock button for 2 sec rather than press and release. Program up to 4 remotes. If cycling the key on-then-off works, you'll probably have to do it quickly 8 times and after the 8th time, locks will cycle down then up and press and release the lock button.
    0helpful
    2answers

    My remote for the keyless entry does not work.

    does trunk button work? panic button?
    here's 2003 info:


    • The doors do not lock/unlock using the remote transmitter
    • Remote transmitter.
    • Driver door module (DDM).
    • Go To Pinpoint Test G .

    SECTION 501-14: Handles, Locks, Latches and Entry Systems 2003 Town Car Workshop Manual
    GENERAL PROCEDURES Remote Transmitter Programming
    1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming that the program mode has been entered.
    1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
      Press any button on the transmitter to be programmed.
    1. If additional keyless entry remote transmitters are to be programmed, repeat Step 2 within 7.5 seconds.
    1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
    --------------------------------------------------------------
    report back
    Not finding what you are looking for?

    1,080 views

    Ask a Question

    Usually answered in minutes!

    Top Lincoln Experts

    ZJ Limited
    ZJ Limited

    Level 3 Expert

    17989 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6988 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    15088 Answers

    Are you a Lincoln Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...