SOURCE: Crank sensor location 1999 dodge durango
the crank sensor is located passenger side back of the engine were the trans and engine come together .there are 2 - 13mm.bolts that bolt to top of the engine.
SOURCE: My 2002 dodge durango wont start ran fine
Does your durango have a security system? Sometimes it may require a keyed entry of the drivers door, but i doubt thats your problem. One thing Durango's are cleptic on is their ability to act all sorts of awkward on a low battery. Maybe a good idea to try a known good battery before we jump into anything further. Any CEL's btw?
SOURCE: 1997 Dodge Intrepid cranks over won't fire
I have this same NO START problem...
Began with tach giving readings not exceding 1200 rpm with strange 4000 + spikes.. Cruse control would not turn on or off at times and indicator light would only work sometimes..Had several episodes of excessive cranking to get it to start.. Stalling out while driving and even at freeway speeds.. Pulling the negative cable for 10 min. allowed it to start although with lots of cranking and put it in limp mode which required another computer reset to get out of.. Had thrown error codes related to cam and crank sensors which were replaced along with coil and manifold temp sensors.. Had the 9 volt power to sensors when key was on but the check engine light does not stay on with all the other idiot lights..
I wish people who respond would read the post first..
Original post states,
Cranks,No spark,No fuel pump run, changed some sensors ect...
If it cranks it ain't the neutral safety switch, starter or battery!! WAKE UP!!
Seems the computer is not turning on the coil, injectors or fuel pump for a reason.. Find that reason and you will find the solution to the problem.. Seeing as that the computers logic states are a dealer secrete the poster as I have changed many parts in blind hope that it will fix the problem.. Relays, sensors and ecu computer.. Did a visual check of all harness potential wear spots like where it crosses over the power rack..
Could it be in the wiring harness inside the dash??
Could it be a bad ground??
Can an alternator that has failed cause the computer not to start??
Can a bad oil pressure sensor cause the computer not to start??
Can signal loss from the TCU or BCU to the ECU cause this??
Is there an undocumented kill if the ECU thinks it was in an accident??
I can ground the relay line from the ECU and the fuel pump runs and pressures up and the other relays turn on as well..
This crank but no start problem seems to be common with a lot of 1994-2001 Dodge and Chrysler owners.. All these systems have become interlaced with undocumented safety features that baffle the DIYer..If you have seen this and have fixed it PLEASE RESPOND!!!!
SOURCE: 2001 dodge 3500 van cam position sensor location
Crank sensor is in the bell housing of the transmission. Cam sensor is in the distributor.
SOURCE: I have a 2000 dodge durango that wont start. I
Have you checked for your DTC code?? The code may help you address the issue that is keeping your engine from starting.
ON-BOARD DIAGNOSTICS
1. Cycle the ignition key ON-OFF-ON-OFF-ON within 5 seconds. To cycle
the ignition key ON means to turn it only as far as it takes to get the
radio to come on. It does not mean to turn the engine on.
2. Count the number of times the "check engine" lamp on the instrument
panel flashes on and off. The number of flashes represents the code.
There is a slight pause between the flashes representing the first and
second digits of the code. Longer pauses separate individual codes. For
example, flash-flash-flash [pause] flash-flash represents the code 32.
A code of "55" represents end of error codes. If this is all you get
then no error codes are stored in the computer. This is the normal
condition for a neon.
CODE Description of Trouble Code
11 Timing belt skipped 1 tooth or more from initial learned value,
Intermittent loss of either camshaft or crankshaft position sensor, No
crank reference signal detected during engine cranking
12 Direct battery input to PCM was disconnected within the last 50 key-on cycles
13 No change in MAP from start to run
14 MAP sensor voltage too low
15 No vehicle speed sensor signal
17 Closed loop temp not reached or engine cold too long
21 02s sensor problem (oxygen sensor), upstream or down stream
22 Engine coolant temp sensor out of range
23 Intake air temp sensor out of range
24 Throttle Position sensor out of range
25 Idle air control motor circuits, target idle not reached (+/- 200),vacuum leak found
27 Injector control circuit
31 Evap purge flow monitor failure or evap solenoid circuit
32 EGR system failure
33 A/C clutch relay circuit
34 Speed control Solenoid circuits
35 Rad Fan control relay circuit
37 Torque converter clutch solenoid CKT or park/neutral switch failure
41 Generator field not switching properly
42 Fuel pump relay control ckt, Auto shutdown relay control ckt, No ASD
relay output voltage at PCM, Fuel level sending unit volts out of
range, Fuel level unit No change over miles
43 Multiple/ single cylinder misfire
44 Battery temp sensor volts out of range
46 Charging system voltage too low
51 Fuel system lean
52 Fuel system rich
53 Internal control failure
54 No Cam signal at PCM
55 End of error messages (If you get this only, no errors were found)
62 PCM failure SRI mile not stored
63 PCM Failure EEPROM write denied
64 Catalytic Converter Efficiency Failure
65 Power steering switch failure
Good luck and thank you for using fixya and keep us posted
426 views
Usually answered in minutes!
With a multi meter check elm, see u tube for how to and specs
Should be E.C..M spell check so sorry.
×