Question about 1990 Daihatsu Rocky

Open Question

Can anybody help with the vacuum pipe sequence on a rocky direct fuel injection

Posted by jon swartzberg on

Ad

1 Related Answer

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi does any 1 no as to what the fuel pipe from the diesel filter on a 2 liter crdi santa fe connects to thanks


I am not familiar with the model.

There can be several pipes connected to a diesel filter but there is usually only one input from the fuel tank and one main output pipe supplying the injection equipment with fuel. Depending on the system there might be a small accumulator in series but otherwise the main output from the filter generally connects direct to the injection pump or to the high pressure pump if it is a common rail type.

Feb 04, 2018 | Cars & Trucks

1 Answer

Kioti tractor 2007 DK45S - will not start. it has a new shutoff fuel solenoid which is working. I checked the glowplugs and they function. Fuel comes to the injection pump. removed injector pipes


bleed the air out of the injector pipes
loosen the nuts at the injectors and wind the engine over ( as if trying to start ) and when you have full fuel drops tighten each pipe and it will start

Jan 21, 2017 | Cars & Trucks

1 Answer

1994 gmc Jimmy wont start , have.replaced everything to make it start. I went threw a mud hole with the driver wheel well off , could my conputar be.fryed


a few basic checks to help you 1.is there a spark to the plugs ? 2.are the air intake pipe and vacuum pipes in good condition ie no splits ,cracks etc ? 3.is there fuel getting to the cylinders , remove a plug turn engine over on the starter a see and smell if there is fuel to the cylinder with plug removed ? 4.that age of vehicle may have a mono port injection system or even a carburetter ,either way remove the air intake pipe from the fuel injection/carb throttle body and try to start, if wont fire up cover this opening , where the air inlet pipe went on ,with your hand to feel if there is suction ,if not there is no compression from the cylinders , this would indicate head gasket or piston ring failure. keep me posted as to the outcome of these checks before spending money on a ECU that may or may not be the problem

May 12, 2014 | Cars & Trucks

2 Answers

Dose a 2000 taurus lx have a single or dual port fuel injection and is the coil pack for one cylinder or is it a pack for all cylinders?


depends on the type of engine. DOHC engine has coil on plug ignition system where the OHV has a coil pack with spark plug wires going to it. Both engines only have one fuel injector per cylinder.

Jul 13, 2011 | 2000 Ford Taurus

2 Answers

Cylinderhead torque stc.


Cylinder Head Removal & Installation SOHC To Remove:
  1. Relieve fuel system pressure.
  2. Remove timing belt cover. Camshaft timing marks kia-03-20-7032.gif

  3. Turn crankshaft until timing mark on front housing and the arrow "2" on the camshaft pulley align.
  4. Loosen lock bolt on tensioner.
  5. Pry tensioner away from timing belt and tighten lock bolt to relieve tension on the timing belt.
  6. Remove timing belt from camshaft pulley.
  7. Disconnect battery negative cable.
  8. Remove 3 bolts that secure accelerator cable and air intake hose to cylinder head cover.
  9. Detach accelerator cable and place off to side.
  10. Remove the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
  11. Disconnect mass air flow sensor electrical connector.
  12. Remove air intake hose.
  13. Remove PCV valve from cylinder head cover.
  14. Remove ISC air hose from idle speed actuator.
  15. Remove air hose from behind intake manifold.
  16. Remove 2 screws from high tension wire protectors.
  17. Detach wire loom from holder at rear of cylinder head cover.
  18. Detach vacuum tube at rear of cylinder head cover.
  19. Remove vacuum pipe. Cylinder Head Cover kia-03-20-7042.gif

  20. Remove 7 cylinder head cover bolts.
  21. Remove cylinder head cover and gasket.
  22. Disconnect 2 ignition coil electrical connectors.
  23. Disconnect 2 fuel injection electrical connectors at rear of cylinder head.
  24. Disconnect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
  25. Disconnect heater hose from elbow.
  26. Disconnect brake booster vacuum hose and cruise control vacuum hose from surge tank.
  27. Detach wire harness from rear of cylinder head.
  28. Disconnect purge control solenoid vacuum hose from intake manifold.
  29. Disconnect fuel hose from fuel connector assembly.
  30. Remove grounding bracket.
  31. Remove 4 bolts and intake manifold bracket.
  32. Remove starter.
  33. Detach water bypass hose from bypass pipe.
  34. Disconnect water hoses from oil cooler.
  35. Disconnect fuel hose from fuel pipe.
  36. Remove exhaust manifold heat shield.
  37. Remove exhaust flange nuts and front exhaust bracket bolt.
  38. Lower exhaust system. Cylinder head bolt loosening sequence kia-03-20-7050.gif

  39. Loosen cylinder head bolts in 3 steps in proper sequence.
  40. Remove cylinder head bolts and washers.
  41. Remove cylinder head, intake manifold and exhaust manifold as an assembly.
To Install:
  1. Install NEW cylinder head gasket.
  2. Install cylinder head, intake manifold and exhaust manifold as an assembly.
  3. Tighten cylinder head bolts in 3 steps in reverse sequence that was used during removal. Tighten bolts to 62 ft lb (84 Nm).
  4. Install front exhaust bracket bolt. Tighten bolt to 20 ft lb (27 Nm).
  5. Install NEW lower exhaust flange gasket and 3 nuts. Tighten nuts to 24 ft lb (31 Nm).
  6. Install exhaust manifold heat shield. Tighten nuts to 35 in lb (4 Nm).
  7. Connect fuel hose to pipe.
  8. Connect 2 hoses to oil cooler.
  9. Attach water bypass hose to bypass pipe.
  10. Install starter and bolts. Tighten bolts to 34 ft lb (46 Nm).
  11. Install intake manifolds bracket and 4 bolts. Tighten bolts to 32 ft lb (45 Nm).
  12. Install grounding bracket.
  13. Connect fuel hose to fuel connector assembly.
  14. Connect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
  15. Connect purge control solenoid vacuum hose to intake manifold.
  16. Attach wire harness from rear of cylinder head.
  17. Connect brake booster vacuum hose and cruise control vacuum hose to surge tank.
  18. Connect heater hose to elbow.
  19. Connect 2 fuel injection electrical connectors at rear of cylinder head.
  20. Connect 2 ignition coil electrical connectors.
  21. Install cylinder head cover.
  22. Install 7 cylinder head cover bolts. Tighten bolts to 60 in lb (7 Nm).
  23. Install vacuum pipe and 2 bolts at rear of cylinder head cover. Tighten bolts to 60 in lb (7 Nm).
  24. Connect vacuum tube to pipe.
  25. Connect loom holder to rear of cylinder head cover.
  26. Install 2 screws to high tension wire protectors.
  27. Install air hose to behind intake manifold.
  28. Install ISC air hose to idle speed actuator.
  29. Install PCV valve to cylinder head cover.
  30. Install air intake hose.
  31. Connect mass air flow sensor electrical connector.
  32. Install the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
  33. Attach accelerator cable.
  34. Install 3 bolts that secure accelerator cable and air intake hose to cylinder head cover. Timing belt pulley timing marks kia-03-20-7035.gif

    NOTE: Timing belt pulley timing mark and timing mark must be aligned.
    Camshaft timing marks kia-03-20-7032.gif

    NOTE: The arrow at "2" on camshaft pulley must be aligned with timing mark on front housing.
  35. Install timing belt.
  36. Install timing belt cover.
  37. Pressurize fuel system.
  38. Start engine and check ignition timing.

Jul 11, 2010 | 1999 Kia Sportage

1 Answer

Car wants to stall changed injecter,egr valve iac


hi
check the all vacuum pipes is their any leaks.

Feb 21, 2010 | 1994 Saturn Sl

1 Answer

Ford transit t350 loss of acceleration


have you tried bypassing the turbo to check if the turbo is helping? is the pump calibrated well? check all the hoses from the turbo especially the turbo boost compensator hose that goes to the injection pump or something like it

Aug 18, 2009 | 2000 Ford F350 Super Duty Super Cab

Not finding what you are looking for?
1990 Daihatsu Rocky Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6523 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...