Question about 2005 Jaguar X-Type

1 Answer

Jaguar x type washer failure

2005 x type jaguar estate.positive feed at the washer pump(both front and rear)but no switched earth.wipers work ok,including 3 wipe for wash.possible control module fault?

Posted by mark956 on

  • 1 more comment 
  • Anonymous Mar 26, 2014

    Rear washer on my estate does not work is there a seperate motor

  • Anonymous Mar 26, 2014

    Rear washer does not work where is rear pump located

  • Anonymous Mar 27, 2014

    Can,t find rear washer pump

×

Ad

1 Answer

Marvin

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Jaguar Master
  • 85,239 Answers

It is more likely the wiper switch has bad contacts or the washer pump is defective, go to the pump and have someone hold wash and check for a 12 volt sigal at the washer fluid pump, if no siganl replace the wiper/washer switch, and if u do have the signal at the pump then the pump is defective.

Posted on Apr 01, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 trialblazer rear window wiper inop. changed switch and motor. no power to motor. cannot find relay nor fuse


There are something's involved that you are not aware of , or familiar with . Electronic control modules .
Rear Wiper/Washer System Controls
• Body control module (BCM)
• Liftgate control module (LGM)
• Rear wiper/washer switch
Do you know what a serial data network is ?
Rear Wiper/Washer System Operation
The rear window wiper/washer switch is an input to the BCM. The requested rear wiper mode is sent to the liftgate control module (LGM) by the BCM as a message on the serial data circuit, and the rear window wiper motor is controlled by the LGM. The switch power circuit to the rear wiper/washer switch is a 12-volt reference supplied by the BCM during ignition on, accessory or RAP power modes. The rear wiper/washer switch is a series of resistors and the switch position is determined by the voltage of the rear wiper/washer switch signal circuit to the BCM. The rear wiper/washer switch has continuity at all times and the BCM expects a rear wiper/washer switch signal voltage in all switch positions including OFF. The rear wiper motor is supplied battery positive voltage and ground. The LGM controls rear wiper motor operation through the rear wiper motor control circuit. The rear wiper motor control circuit is supplied a battery positive reference voltage by the rear wiper motor module and is pulse width modulated to ground by the LGM. The duty cycle of the pulse width modulation determines the rear wiper motor operating mode. The liftglass and liftgate ajar switches are inputs to the LGM and must be in an inactive state in order for rear wiper washer system operation to be enabled. When an ajar switch is active the LGM suspends wiper motor operation directly and sends the ajar switch status messages over the serial data circuit enabling the BCM to suspend washer pump operation. The rear window washer pump is controlled by the BCM through the rear washer relay. Battery positive voltage is supplied to the coil and switch sides of the rear washer relay. When the rear window wash request is active the BCM energizes the relay by grounding the relay coil through the rear washer relay control circuit. When the relay is energized battery positive voltage to the relay switch is supplied to the washer pump control circuit.

Your best bet , take it to a qualified repair shop and have it checked for DTC'S - diagnostic trouble codes .
DTC B1017 or B3970
The rear wiper motor is supplied battery positive voltage and ground. The liftgate control module controls rear wiper motor operation through the rear wiper motor control circuit. The rear wiper motor control circuit is supplied a battery positive reference voltage by the rear wiper motor module and is pulse width modulated to ground by the liftgate control module. The duty cycle of the pulse width modulation determines the rear wiper motor operating mode.
DTC B3799

2
Turn the ignition ON.
Operate the rear wiper switch through all the switch positions.
Does the rear window wiper operate normally?
--
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Install a scan tool.
Display the liftgate control module data list.
Observe the following parameters while operating the respective switches. Refer to Scan Tool Data List for typical values.
• Liftgate Ajar Switch
• Liftglass Ajar Switch
Did the scan tool indicate the correct switch positions?
--
Go to Step 4
Go to Courtesy Lamps Inoperative in Lighting Systems
4
Observe the requested rear wiper parameter in LGM data list.
Operate the rear wiper switch through all the switch positions.
Does the scan tool indicate the correct requested rear wiper parameter in relation to the switch position?
--
Go to Step 5
Go to Step 6

Feb 06, 2017 | 2002 Chevrolet TrailBlazer

1 Answer

In my 2007 Saturn Vue there is what I think is an air pump which is cracked that one port is not connected to anything.


There is a electric motor that pumps washer fluid . Located in the bottom of the washer fluid tank .
Wash Operation (Front and Rear Wipers)
The front and rear washer systems use the same windshield washer fluid pump. When either the front or rear wiper is in the washer position voltage will be supplied to one side of the windshield washer fluid pump (depending on whether it is front or rear), while the other side of the pump is grounded.
At this point, the windshield washer fluid pump sprays solvent onto the windshield. When the front or rear washer is activated, the BCM receives an input from the switch that is activated. The BCM will control the wipers while in the WASH mode. The BCM will control either the front wiper relay or the rear wiper relay to turn on the wipers. The windshield wipers operate at low speed for 3 swipes and returns to the park position.

When turning on the washers do you hear the motor run ? Have some one try it while you listen at the washer fluid tank ! These pump motors do go bad .
turn OFF the ignition.
Disconnect the harness electrical connector of the windshield washer fluid pump.
Connect a test lamp from the windshield washer pump control circuit to a good ground .
Turn ON the ignition, with the engine OFF.
Press the front washer switch.
Does the test lamp illuminate?
YES or NO !

Nov 18, 2016 | Saturn Cars & Trucks

1 Answer

Which fuse controls front windshield wiper pump


Do the wipers work ? Fuse for wipers is same as washer pump .
Principles of Operation
The wiper motors receive inputs from the following:
  • Multi-function switch
  • Powertrain control module (PCM)
  • Ignition switch
  • Smart junction box (SJB)
The following components are integrated in the wiper motors:
  • Windshield wiper motor module
  • High/low speed relay
  • Run/park relay
  • Washer pump relay
  • Park sense (Hall-effect sensor)
Washer System
The windshield washer and the rear window washer are activated by the internal wiper motor modules when it receives a ground from the multi-function switch between the washer inputs. Depending on the correct ground, the internal wiper motor modules activate either the windshield washer or rear window washer relays (internal) by grounding the respective relay coil. When either module is activated, it connects voltage to the washer pump while the deactivated module provides ground to the washer pump. In this manner, voltage polarity is reversible to achieve directional change of the washer pump and washer fluid.
  • The washer pump is inoperative
  • Circuitry
  • Washer pump
  • Multi-function switch
  • Windshield wiper motor
  • Rear window wiper motor
  • Go To Pinpoint Test I .
Does your expedition have programmable/recall memory option for seats an mirrors ?
Driver Seat Module
The power driver seat and power exterior mirrors are controlled by the driver seat module (DSM) only when the vehicle is equipped with the programmable/recall memory option.
On the Expedition Limited, the power fold exterior mirror option is controlled by the DSM. Before running a self-test or retrieving codes, the power fold switch must be inactive for at least 30 seconds.
This is a complex vehicle , electronics , control modules an serial data communication networks. You mite be better off taking it to the dealer or some other repair shop . There could be DTC'S - diagnostic trouble codes stored in the SJB - body control module !
B1667 Mirror Driver Up/Down Motor Stalled Go To Pinpoint Test D . B1668 Mirror Driver Right/Left Motor Stalled Go To Pinpoint Test D . B1669 Mirror Passenger Up/Down Motor Stalled Go To Pinpoint Test D . B1670 Mirror Passenger Right/Left Motor Stalled Go To Pinpoint Test D . B1735 Mirror Driver Vertical Switch Circuit Short to Battery Go To Pinpoint Test D . B1739 Mirror Driver Horizontal Switch Circuit Short to Battery Go To Pinpoint Test D . B1743 Mirror Passenger Vertical Switch Circuit Short to Battery Go To Pinpoint Test D . B1747 Mirror Passenger Horizontal Switch Circuit Short to Battery Go To Pinpoint Test D . B2312 Mirror Horizontal Feedback Potentiometer Circuit Failure Go To Pinpoint Test D . B2314 Mirror Passenger Horizontal Feedback Potentiometer Circuit Short to Battery Go To Pinpoint Test D . B2316 Mirror Passenger Vertical Feedback Potentiometer Circuit Failure Go To Pinpoint Test D . B2318 Mirror Passenger Vertical Feedback Potentiometer Circuit Short to Battery Go To Pinpoint Test D . B2320 Mirror Driver Horizontal Feedback Potentiometer Circuit Failure Go To Pinpoint Test D . B2322 Mirror Driver Horizontal Feedback Potentiometer Circuit Short to Battery Go To Pinpoint Test D . Normal Operation During normal operation, when the front wiper wash is selected, the windshield wiper motor provides power to the washer pump through circuit CRW14 (BU/WH) and ground is provided to the washer pump through circuit CRW12 (GY/OG) and the rear wiper motor. If rear wiper wash is selected, the rear wiper motor provides power to the washer pump through circuit CRW12 (GY/OG) and ground is provided to the washer pump through circuit CRW14 (BU/WH) and the windshield wiper motor.
    Possible Causes
  • Multi-function switch
  • Open in circuit CRW14 (BU/WH), CRW12 (GY/OG), CRW07 (GY/BN), CRW20 (GY/YE), SBB49 (RD) or GD149 (BK/GY)
  • Short to ground in circuit CRW14 (BU/WH), CRW12 (GY/OG), CRW07 (GY/BN) or CRW20 (GY/YE)
  • Washer pump
  • Windshield wiper motor
  • Rear wiper motor
    This is

Feb 02, 2016 | 2010 Ford Expedition

1 Answer

X type estate 06 rear washer doesnt wash. pump appears to be working, jet is clear but no water. Can u help?


plastic feed tube in the rubber boot from door frame to tailgate is damaged ,well this is the most obvious fault ,but a jaguar estate car and i bet its diesel as well ?? not like a nice mk2 3.8 with overdrive or a XJ6 is it

Nov 29, 2010 | 2005 Jaguar X-Type

1 Answer

The rear washer on my 2005 X-Type estate has failed. The pump at the front is working. There are no internal or external leaks. The rear gate nozzle is not blocked. It looks like a blockage in the...


Do you hear the washer pump run when trying to wash the rear? Fuse number F23 20 amps, powers the rear pump the diagram is not clear as to hose routing. I would suspect there is a check valve in the system near the rear hatch . You can trace the hose from the door down the side.

Nov 19, 2010 | 2002 Jaguar X-Type

2 Answers

Jaguar X Type Estate 2005. Wipers not working. Changed Wiper stalk & Relay. Still blows fuse when switching on ignition.


If the wiper motor is shot then it will be overcharging inside the motor itself, causing it to blow the fuse, although it may still seem to work.

Also check the wiring to the motor and ensure its not making contact with anything. If the car has been icy then the ice may have froze to the motor and then ark'ed when used.

Jan 15, 2010 | 2005 Jaguar X-Type

1 Answer

Rear window wiper washer don't work fuses and


The switch may not be making contact or wire to switch may have come off. If poss check voltage on the water pump for your rear screen. You may also have a bad earth.

Dec 07, 2009 | 2002 Chevrolet Blazer

2 Answers

My windshield water does not work


Check fuse first, then unplug the connector going into the washer tank and take a 12 volt tester and plug it into the hot side of the wire while attempting to wash your windows...does the tester come on. If the answer is yes, your pump has failed.

Nov 10, 2009 | 2006 Dodge Durango

1 Answer

Jaguar X Type estate rear hatch glass pops open on start up


Hi the fault is usually the  button for opening the rear glass, this can be changed easily if it is not sezed to the wiper spindle  D 

Jan 18, 2009 | 2005 Jaguar X-Type

1 Answer

99 Nissan Quest real wiper runs continually when ignition is on


Principles of Operation
Operation of the windshield wiper and washer is controlled by the front wiper/washer amplifier assembly. The front wiper/washer amplifier input comes from the multifunction switch by means of a voltage divider circuit. A constant voltage is applied to the multifunction switch by the front wiper/washer amplifier. When the multifunction switch is moved into the LO, HI, or intermittent position, the voltage is directed through a series of resistors. This results in various voltages being returned to the module for each switch position. The module then grounds the appropriate circuit, based on the voltage signal received back from the multifunction switch. This causes the wipers to run intermittently, or at the appropriate speed. Voltage is supplied to the wiper motor by the CJB fuse F46 (20A).
When the multifunction switch wash button is depressed, it bypasses all of the resistors returning a full voltage signal to the module. The module then grounds the appropriate circuits to operate the windshield washer pump for as long as the switch is depressed. The windshield wiper speed is dependent on the position of the windshield wiper/washer switch.
Voltage for the windshield washer pump is also provided by CJB fuse F46 (20A).
Operation of the rear wiper and washer is controlled by the rear wiper/washer switch.
Voltage is supplied to the rear window wiper motor by the fuse junction panel fuse F44 (10A).
The rear window wiper motor ground is made or broken by the rear wiper/washer switch. When the rear wiper/washer switch is moved into the WIPER position, it grounds the rear window wiper motor circuit, causing the rear window wiper motor to run once every 10-15 seconds.
Voltage to the rear washer pump motor is also supplied by the CJB fuse F44 (10A). The rear washer pump is directly controlled by the rear wiper/washer switch which makes or breaks the ground for the washer pump motor, depending upon its position.
If the vehicle is equipped with a movable liftgate glass, a liftgate glass switch is utilized to prevent rear window wiper operation when the liftgate glass is open. This same switch also causes the rear window wiper to drop down approximately three inches when the liftgate glass latch is released.
------------------------------------------------------------------------------------------
  • The wipers stay on continuously — rear wiper
  • Circuit.
  • Rear wiper/washer switch.
  • GO to Pinpoint Test L .


---------------------------------------------------------------------------------------------
Measure the resistance between rear wiper/washer switch C288 pin 6, component side and rear wiper/washer switch C288 pin 2, component side.
  • Is the resistance less than 5 ohms with the switch depressed, and greater than 10,000 ohms with it released?
sxv~us~en~file=arrow.gif~gen~ref.gifYes GO to L2 .
sxv~us~en~file=arrow.gif~gen~ref.gifNo INSTALL a new rear wiper/washer switch. TEST the system for normal operation.

Measure the resistance between rear wiper/washer switch C288 pin 6, circuit WB08 (BU/YE), harness side and ground.
  • Is the resistance greater than 10,000 ohms?
sxv~us~en~file=arrow.gif~gen~ref.gifYes INSTALL a new rear wiper /washer switch. TEST the system for normal operation.
sxv~us~en~file=arrow.gif~gen~ref.gifNo REPAIR circuit WB08 (BU/YE). TEST the system for normal operation.

65501dd.gif 7e9d21a.gif

Dec 08, 2008 | 1999 Nissan Quest

Not finding what you are looking for?
2005 Jaguar X-Type Logo

840 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...