Take out dash(tundra) for antenna installation

remove remote start and clear the no start problem first.

https://www.justanswer.com/toyota/5do8v-toyota-tundra-sr5-2000-tundra-changed-battery.html

Here's a video on installing seat covers for your Tundra, 07 13 Toyota Tundra factory seat covers installed I had a 2004 Tundra,bought seat covers from Dealer and installed,real easy.I had leather seats.Here's a video of my Tundra I sold,you will see the seat covers,cause I show them. 04 TOYOTA TUNDRA SR5 TRD THE DESERT SAND WALK THRU

YES,CHECK THE FUSE BOX AT DRIVER SIDE,DID YOU PUT A RADAR DETECTOR IN THE LIGHTER,IF SO,THEN THE FUSE BLEW,HAPPENED TO MY 2004 TUNDRA.THE LIGHTER OUTLET IS FOR LIGHTER ONLY.

Hey Who ever , I included a diagram of it WOW your going to want to dive into the deep end of an EMPTY pool , go to auto zone library (its all free) log in ,list your vehicle an go to repair guide and then vehicle repair then to heating & cooling look to left of page and click on heater core GOOD LUCK. Woody oh ya the dash has to come out

You will have to un-install the entire antenna system from the inside.
remove the panel carefully adjacent to the antenna system
undo the bolts and clamps that hold the system in place
you can try and install the new antenna piece without disconnecting the transfer wire that goes back to the radio. But usually you will need to get and install a new system.
just to keep you going in the mean time you could just use a old wire coat hanger "classic" just bend the hook straight and shove it in, you have your sounds back.
all the best

Anti theft is active.

Please don't forget to rate!

1. Before servicing the vehicle, refer to the Precautions section.
   

1. Remove or disconnect the following:
2. Front wheel
   

• Strut-to-lower control arm nut/bolt and the strut
  
• Strut-to-chassis nuts/bolts and the strut
  

Lower control arm Tundra

To install:

1. Install or connect the following:
   
   • Strut to the chassis. Torque the nuts/bolts to 33 ft. lbs. (45 Nm).
     
   • Strut to the lower control arm. Torque the nut/bolt to 144 ft. lbs. (195 Nm).
     
   • Front wheel
     

// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 31; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

Hi. Please see procedure below:

Determine which alternator your Toyota Tundra will need. You'll want to be sure the new alternator is compatible with your Tundra's engine. Models built from 2000 to 2004 have a 3.4 L or 4.7 L engine. Models made from 2005 to 2006 offer options for a 4.0 L or 4.7 L engine. Starting in 2007, the Tundra is available with 4.0 L, 4.7 L and 5.7 L engines.

Disconnect the negative battery cable with a socket wrench. Remove the gravel shield if you need to access the alternator from under the car. Remove the electrical connector and unfasten the retaining nut on the alternator terminal with a socket wrench. This will allow you to remove the battery terminal wire.

Unfasten the lock nut, pivot bolt and adjusting bolt on the alternator with a socket wrench. Remove the drive belt and take the alternator off the vehicle.

Install the new alternator assembly. Use a torque wrench to tighten the lock nut to 25 ft. lbs. and the pivot bolt to 38 ft. lbs. Attach the adjusting bolt.

Connect the electrical harness and battery terminal wire to the alternator and fasten the retaining nut to the alternator terminal with a socket wrench. Install the gravel shield if you removed it. Replace the drive belt and restore it to the proper tension. Reconnect the negative battery cable with a socket wrench.

Thanks!

hello please help I got a tundra 2007 w/ no hazard turn signal & running lights (front yellow lights) HELP PLEASE all fuses check ok.

Is it a power antenna ? or a regular antenna ? you may have to remove the wheel well liner to acess the antenna.Remove the clips that attach the liner.Hope this helps.