2000 Mazda Protege Logo

Related Topics:

Anonymous Posted on Jun 28, 2013

Low beam how to pull the stering wheel of a mazda protege 2000

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

  • Contributor 1 Answer
  • Posted on Jul 24, 2013
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Joined: Jul 24, 2013
Answers
1
Questions
0
Helped
97
Points
1

Make sure you disconnect the battery first, you don't want to take a chance on setting off the airbag. After you remove the airbag, you will have to remove the steering wheel nut, and steering wheel spokes. You will require a puller to pull the steering wheel off the shaft.

5 Related Answers

Anonymous

  • 52 Answers
  • Posted on May 14, 2009

SOURCE: My 2000 Mazda Protege DX has a tight steering. Can

hey srinivasbham,

This is how i would start, the most common problem with loosing your power steering is low fluid. The first thing i would do is check your power steering level. If it is significantly low, this is most likely your problem, just top it off and your on your way. Two other common problems are the power steering pump failing and a loose serpentine belt.

If the pump is failing then it starts to make a groaning noise, but before you think the pump is bad make sure the fluid is full. Also if your serpentine belt is the problem you will get a high pitch squeal while turning.
Start their, and let me know i you need more info.

Ad

Anonymous

  • 115 Answers
  • Posted on Jun 24, 2009

SOURCE: Locating oil filter on 2000 Mazda Protege

on the backside of the motor, towards the firewall. look above the drive shaft. it's about haft way up the motor.

Anonymous

  • 10319 Answers
  • Posted on May 01, 2010

SOURCE: how to replace a timing belt on a 2000 Mazda Protege

Here is a website that a free manual can be down loaded for your vehicle


http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

Anonymous

  • 44 Answers
  • Posted on Jul 23, 2011

SOURCE: 2000 Mazda Protege How do I replace the license

Try from inside the trunk.

Anonymous

  • 3 Answers
  • Posted on Nov 22, 2011

SOURCE: Mazda Protege 2000 - low

turn signal switch needs changing, it only has 1 or 2 screws that hold it in there. the dimmer is bad

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

The low beams stopped working but my high beams still do on my 1999 Mazda Protege.

  1. I own a Protege and once the low beam bulb burns on one headlight the car electronics quickly cook the bulb on the other headlight as well. it is a poor design by the mfr. Pull both bulbs to make sure the low beam is not cooked.
0helpful
1answer
1helpful
1answer

A/c recharge port on 2000 mazda protege

L- is low side & the only one that
will fit anything your trying to do
0helpful
1answer

Mazda Protege 2000 - low beams stopped working, high beams are fine, I replaced bulb and the fuses seem to be OK too? Any ideas? Thanks a lot!

turn signal switch needs changing, it only has 1 or 2 screws that hold it in there. the dimmer is bad
0helpful
1answer

1999 mazda protege lo beams don't work, hi beam light on with low or hi. Fuses good, no relay

the relay is built into the switch itself which is likely what is faulty.
0helpful
1answer

Low beam not working

the dimmer switch is bad if low beams are out
0helpful
1answer

Headlights

hi thank you your help, id like to do the work myself. how would i go about thatg exactly?
Not finding what you are looking for?

107 views

Ask a Question

Usually answered in minutes!

Top Mazda Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...