Question about Cars & Trucks

Open Question

Upright cherry picker wiring diagram - Cars & Trucks

Posted by Anonymous on

Ad

1 Related Answer

Anonymous

  • 87 Answers

SOURCE: Serpentine belt

yes the front engine mount must be removed use the jack that comes with the car and a wood block 2x4 works great

Posted on Jun 08, 2008

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What do i need to replace the motor in a 1998 chevy cavalier


Floor jack, jack stands, cherry picker, common sense, mechanical ability, basic hand tools, service manual helps.

Jun 08, 2015 | Cars & Trucks

1 Answer

How do I replace the motor mounts on my 2001 Toyota Camry Solora xle v6


Ok, first off apply E brake. Second, locate motor mounts usually on side bottom, connect to frame. Third jack up car place jack stands. Fourth,disconnect all wiring, maf, pretty much anything and everything that will get in way. Fifth, grab cherry picker, connect engine to cherry picker. Sixth, disconnect engine from trans, or leave connected but might be more difficult for some. Seventh,unbolt engine from mounts(usually 3or so bolts on each mount), do not rock engine, raise cherry picker(or crane some call it different)when tension on chain slowly rock engine. Should pop out unless you missed a bolt.

Feb 20, 2015 | 2001 Toyota Camry Solara

1 Answer

What would it cost a mechanic to install motor mounts on a 1995 gmc sonoma 4.3 litre 4*4


Im sure your 95 is no different then my 01 sonoma 4x4 u shouldn't need a cherry picker to do the engine mounts a small block of wood and a floor jack to support the engine from underneath and take a little bit of the load off the mount should work you dont have to lift the engine out to do them its not easy this way but is possible and cost less money working for a gm parts department and a former tech you would be spending and average of 75 to 100 an hour labor wise depending on what shop u take it to and what shop labor rates at like near you I would estimate an easy 2 hours labor but it all goes by book time thats or determined at the shops

Mar 27, 2014 | 1995 GMC Sonoma

1 Answer

How to change motor mounts


REMOVE TRANS, ENGINE AND ALL RELATED PARTS...USE A CHERRY PICKER. UNBOLT OLD BOLT IN NEW

Nov 14, 2013 | Pontiac Cars & Trucks

1 Answer

Removing transmission and motor


cherry picker it just depends

Nov 08, 2013 | 2003 Dodge Stratus

1 Answer

Fuel pump 2001 silverado


You can either drop the tank, if its near empty that is; but it hardly ever works out that way. When I did mine I took the bed off. Unbolt I believe 8 bolts , wiring for taillights, and (I used my cherry picker) lift the bed up. The pump assy goes into the tank, some twist out, some might have a couple screws holding it. I don't remember. Assembly is the opposite of removal.

Oct 17, 2012 | 1998 Dodge Dakota

1 Answer

On a 1997 chevy astro to pull out the engine does it come out under the van? theres no way to bring out thru the front with out haviing to cut,


Comes up and out of the 'Dogbox' with a cherry picker. (Can you say No Fun?)

You go through the side sliding door with a cherry picker.

Take the engine cover loose, and remove it. Now attach your lifting cradle, (Or chain with bolts so that the chain doesn't slide in the lifting hook), to the top of the engine. Lift up and back. Keep working it up, and out, of that small compartment. Use three people, and BE CAREFUL! Always have an exit planned in case something goes wrong. Stand away from the engine, not crowded down in there as you remove it.

Jul 12, 2009 | 1996 Chevrolet Astro

1 Answer

Easiest way to remove bed on 1988 s-10


pull all bolts get a engine puller or as i call it a cherry picker and hook one chain to the hook by the passenger side closest to the cab and the other side to the driverside by the tailgate.then get another chain and do exactly the opposite so that you make an X the hook the cherry picker/engine puller to the center and lift slowly..

Dec 01, 2008 | Chevrolet S 10 Cars & Trucks

2 Answers

Engine removal for toyota camry


its so easy just remove the engine mouts with a cherry picker holding the engine by the lift claws, then just remove the transaxle by a couple bolts then remove all other wiring and hosing and lift it out simple

Jul 27, 2008 | Toyota Camry Cars & Trucks

1 Answer

Electric Fuel Pump on an '98 Sierra


when mine went bad I pulled the bed off and moved it back enough toget to the top of the fuel tank it was easier to remove and replace versus dropping the tank tookme and my buddy about 2 hours rig a sling and use a cherry picker to lift bed don't forget to unplug wire harness hope this helps

Jul 16, 2008 | 1998 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

john h

Level 3 Expert

23515 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6528 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...