Oil in air intake hose

Sounds like timing belt

Hi
The engine produce little oil steam when is at normal temperature, this is normal.
This steam goes to the air cleaner for recycling.
Now, the reasons to see oil dripping from the air cleaner are:
Engine oil overfilled, or engine breather valve( if fitted) faulty, or the piston rings causing the pressure to scape into the oil sump ( this means engine damage).
get a technician to chem it.
good luck.

If you have oil in the hose for the air filter, the engine crankcase is letting oil vapors out thru the intake hose, instead of pulling fresh air into the crankcase thru the hose. The most common reasons are a faulty PCV system or blow-by from weak cylinder rings.
The crankcase has too much pressure.

The oil filter on your 2004 sunfire is under the air intake hose. you take this hose off by loosening the two clamps that hold it onto the air filter housing and the air intake. Under that is a black cap with a large hex head on it, i believe 1.25 inch. that is the oil filter cap. take that off and pull the used oil filter off the bottom.

The pcv valve vents the crankcase vapors into the intake to be burned. That vapor has oil in it and the oil will sometimes accumulate in the hose and throttle body. It's normal for all cars to have a bit of oil in there. Just needs to be cleaned out every so often.

Cylinder Head Removal & Installation SOHC To Remove:

1. Relieve fuel system pressure.
2. Remove timing belt cover. Camshaft timing marks
   
   
3. Turn crankshaft until timing mark on front housing and the arrow "2" on the camshaft pulley align.
4. Loosen lock bolt on tensioner.
5. Pry tensioner away from timing belt and tighten lock bolt to relieve tension on the timing belt.
6. Remove timing belt from camshaft pulley.
7. Disconnect battery negative cable.
8. Remove 3 bolts that secure accelerator cable and air intake hose to cylinder head cover.
9. Detach accelerator cable and place off to side.
10. Remove the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
11. Disconnect mass air flow sensor electrical connector.
12. Remove air intake hose.
13. Remove PCV valve from cylinder head cover.
14. Remove ISC air hose from idle speed actuator.
15. Remove air hose from behind intake manifold.
16. Remove 2 screws from high tension wire protectors.
17. Detach wire loom from holder at rear of cylinder head cover.
18. Detach vacuum tube at rear of cylinder head cover.
19. Remove vacuum pipe. Cylinder Head Cover
    
    
20. Remove 7 cylinder head cover bolts.
21. Remove cylinder head cover and gasket.
22. Disconnect 2 ignition coil electrical connectors.
23. Disconnect 2 fuel injection electrical connectors at rear of cylinder head.
24. Disconnect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
25. Disconnect heater hose from elbow.
26. Disconnect brake booster vacuum hose and cruise control vacuum hose from surge tank.
27. Detach wire harness from rear of cylinder head.
28. Disconnect purge control solenoid vacuum hose from intake manifold.
29. Disconnect fuel hose from fuel connector assembly.
30. Remove grounding bracket.
31. Remove 4 bolts and intake manifold bracket.
32. Remove starter.
33. Detach water bypass hose from bypass pipe.
34. Disconnect water hoses from oil cooler.
35. Disconnect fuel hose from fuel pipe.
36. Remove exhaust manifold heat shield.
37. Remove exhaust flange nuts and front exhaust bracket bolt.
38. Lower exhaust system. Cylinder head bolt loosening sequence
    
    
39. Loosen cylinder head bolts in 3 steps in proper sequence.
40. Remove cylinder head bolts and washers.
41. Remove cylinder head, intake manifold and exhaust manifold as an assembly.

To Install:

1. Install NEW cylinder head gasket.
2. Install cylinder head, intake manifold and exhaust manifold as an assembly.
3. Tighten cylinder head bolts in 3 steps in reverse sequence that was used during removal. Tighten bolts to 62 ft lb (84 Nm).
4. Install front exhaust bracket bolt. Tighten bolt to 20 ft lb (27 Nm).
5. Install NEW lower exhaust flange gasket and 3 nuts. Tighten nuts to 24 ft lb (31 Nm).
6. Install exhaust manifold heat shield. Tighten nuts to 35 in lb (4 Nm).
7. Connect fuel hose to pipe.
8. Connect 2 hoses to oil cooler.
9. Attach water bypass hose to bypass pipe.
10. Install starter and bolts. Tighten bolts to 34 ft lb (46 Nm).
11. Install intake manifolds bracket and 4 bolts. Tighten bolts to 32 ft lb (45 Nm).
12. Install grounding bracket.
13. Connect fuel hose to fuel connector assembly.
14. Connect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
15. Connect purge control solenoid vacuum hose to intake manifold.
16. Attach wire harness from rear of cylinder head.
17. Connect brake booster vacuum hose and cruise control vacuum hose to surge tank.
18. Connect heater hose to elbow.
19. Connect 2 fuel injection electrical connectors at rear of cylinder head.
20. Connect 2 ignition coil electrical connectors.
21. Install cylinder head cover.
22. Install 7 cylinder head cover bolts. Tighten bolts to 60 in lb (7 Nm).
23. Install vacuum pipe and 2 bolts at rear of cylinder head cover. Tighten bolts to 60 in lb (7 Nm).
24. Connect vacuum tube to pipe.
25. Connect loom holder to rear of cylinder head cover.
26. Install 2 screws to high tension wire protectors.
27. Install air hose to behind intake manifold.
28. Install ISC air hose to idle speed actuator.
29. Install PCV valve to cylinder head cover.
30. Install air intake hose.
31. Connect mass air flow sensor electrical connector.
32. Install the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
33. Attach accelerator cable.
34. Install 3 bolts that secure accelerator cable and air intake hose to cylinder head cover. Timing belt pulley timing marks
    
    NOTE: Timing belt pulley timing mark and timing mark must be aligned.
    Camshaft timing marks
    
    NOTE: The arrow at "2" on camshaft pulley must be aligned with timing mark on front housing.
    
35. Install timing belt.
36. Install timing belt cover.
37. Pressurize fuel system.
38. Start engine and check ignition timing.

This is usually an indication of "blowback" caused by worn piston rings. How many miles on the engine? There is not a cheap solution if it is blowback.

Had the same problem. 2005 Cadillac CTS with the 3.6L V6 would not start after a oil change. I started looking for wires and stuff that might have been disconnected. That is when I realized that I had also checked the air filter. The hose from the air filter box to the intake had come slightly loose from the intake. The car would not run with an air leak at the air cleaner box box hose. Put the hose on tight and problem fixed.

Sounds to me you blow by. Thats when either rings on the pistons are worn letting oil pass by or you have a scorned cylinder which also is letting oil get by. Should get a compression check done to make sure.

possible worn out motor but before i say that ck to see if the intake gaskets are blown is it a 5.0 or a 5.7 or a 3.4