Question about 1995 GMC Sierra

2 Answers

Brake Light switch removal GMC PC

Ok, I can actually get my hand around my brake light switch on a 1995 GMC PU...How do I actually detach the switch to replace with a new one??? Help...too many people honking at me

Posted by kalvikinkelo on

Ad

2 Answers

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 71 Answers

Just unplug and unscrew its threaded like a bolt

Posted on Mar 28, 2009

Ad

Anonymous

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a 1995 gmc sierra and when the headlights are on or i aply the brake while signaling my signals go rapidly fast what could this be??

Posted on May 02, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 GMC Jimmy brake lights not working


Brake lights run through the hazzard switch. There are known problems with this, and the multifunction switch. You may need to buy a new hazzard switch and OR the multifunction switch. Before you do that, check the pigtail that goes into the brake switch up by the fender, make sure it's not shorting out up there. Happened to me!

May 06, 2017 | 1995 GMC Jimmy

2 Answers

Replaced brake switch,new brake-light bulbs, fuse ok, still get no brake lights, and turn signals in rear not working....what can i do ?


Hi, assuming you have the correct bulbs installed, the wires leaving the turn signal switch seem to be broken along their trip to the back of the truck. If you tell me your model and year, I may be able to tell you where to look for the problem.

Aug 28, 2011 | GMC Suburban Cars & Trucks

1 Answer

Brakes lights dont come on at all everything else works but brake lights


check brake light fuse, if fuse is ok replace brake light switch, it is located at top of brake pedal arm.

Mar 22, 2011 | 1995 GMC Jimmy

1 Answer

Brake lights don't work how to fix


When a vehicle's brake lights all go out at the same time, the culprit is usually the
"stoplight Switch" which is operated by depressing the brake pedal.

To replace a stoplight switch, first determine what type of switch you have.
If you have an electrical switch mounted to the brake pedal in the passenger compartment:
  • Unscrew the switch.
  • Unplug the wires.
  • Replace with a new switch. Adjust as needed.
  • Plug the wires back in.
If you have a hydraulic pressure switch that is mounted in the brake master cylinder:
  • Mark and disconnect the wires.
  • Unscrew the switch.
  • Screw the replacement switch in.
  • Reconnect the wires
Here's a picture of the "Stoplight Switch", aka Brake Light Switch - 1995 GMC K1500 Sierra

archaeology_14.jpg

Brake lights (stoplights) are activated by a mechanical switch on the brake pedal.
To test a suspected bad stoplight switch, bypass it with a jumper wire. The stoplights should light when the wires are connected. Use the test light to see if there is power at one of the lights.
  • If the lights come on when the wires are connected but not when the brakes are applied, replace the switch.
  • If the stoplights operate without the key on, remove the stoplight fuse before removing the switch.
  • If the new switch is adjustable, adjust it so that it is open when the pedal is released.lights should come on about 1/4" after the pedal is applied.

Feb 20, 2011 | 1995 GMC Sierra

1 Answer

1995 gmc K2500 left and right brake lights come on with ignition turned on. 3rd brake light comes on when you step on the brake 4 way flashers do not work. Ignition turned off 4 way flashers and brake...


I think your trouble is in the turn signall switch, just had the same trouble on my truck. Turn signall switch is about $250 because it is actually turn signalls, wipers, washers, 4 ways, and dimmer all in one.

May 12, 2010 | Cars & Trucks

1 Answer

Brake lights do not work on a 1993 v-6 PU Can I obtain a schematic wiring diagram from you?


You need to replace the brake light switch (aka stop light switch) which is mounted on the upper brake pedal, with a electric plug in. If this doesn't help, let me know.

Oct 23, 2009 | 1993 GMC Sierra

1 Answer

Brake switch


Replace the switch it's made of plastic and does not hold on, real comom problem and is a easy fix fust push pedal down with hand and unscrew the switch when you unhook harness first just pulls off.

Aug 19, 2009 | 1995 GMC Sierra C1500

1 Answer

No brake lights


ck bulbs brake lite switch above pedal
shack

Apr 16, 2009 | GMC Sierra 1500 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,025 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...