2005 Chevrolet Uplander Logo

Related Topics:

Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

ABS code c0040 and c0041,right wheel speed control sensor and right wheel speed control circuit

The ABS light comes and go,the scanner tells me these two codes c0040 and c0041.Is may be the durty harness? Should I try first to clean the wire and the connector before replacing the sensor itself? And most important ,where is the harness and the sensor located in order to find the connector?? Thanks

1 Answer

Rick M

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Chevrolet Master 4,148 Answers
  • Posted on Jan 08, 2018
Rick M
Chevrolet Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Jun 26, 2017
Answers
4148
Questions
0
Helped
1254697
Points
13941

5 Related Answers

Anonymous

  • 59 Answers
  • Posted on Sep 20, 2008

SOURCE: 2002 2WD CHEVY TAHOE ABS

Its possible that right wheel speed sensor is dropping out early making the truck think that wheel is locking up. That will activate the ABS and let the brake go on the right wheel which will make the vehicle pull slightly left. The only way to know for sure is to watch the wheel speeds on a scanner and see which one is drpping out first and replacing that speed sensor/bearing assembly.

good Luck

Ad

Anonymous

  • 114 Answers
  • Posted on Jan 24, 2009

SOURCE: obd 2 connector does not work with any code scanner

HI there....Check to see if the code reader is a CAN OBD 2 code reader. If it is only OBD2 , that may be the problem. In 2003 Some vehicle manufacturers ( ford,Gm,Mazda and Saab) began using a new computer protocol called Controller Area Network (CAN) with the OBD2 and if your vehicle is CAN OBD 2 the simple OBD2 code reader will not work.Contact your local dealer to determine if you vehicle is CAN or not or find a code reader that is CAN OBD2 capable. Hope this helps you out

Anonymous

  • 1 Answer
  • Posted on Feb 16, 2009

SOURCE: trying to locate MAF sensor

Look near your A/C system and under the overflow hose for the coolant. It is a round can looking thing with a small wiring harness attached on top. There rae 3 hex screws holding it on to the bracket. Remove these and slip it off of the air intake tube. Use a small screwdriver to depress the small latch on the inside of the harness and gently pull it off. Disassemble the MAF sensor from the mounting plate, remove it from the vehicle and spray the wires with carburetor cleaner several times. That should clean it up for you. Good luck and let me know if you need more info.

Anonymous

  • 54 Answers
  • Posted on May 04, 2009

SOURCE: 2003 silverado 39,ooo miles. due

make sure all tires are same size and inflated to correct pressure

co7196

Ned C Cook

  • 3433 Answers
  • Posted on May 06, 2009

SOURCE: looking for color code (diagram) - 7 wire trailer harness/wiring

If you haven't purchased the plugs yet. The wire color codes should be included in the package.

  • If you are using used plugs ck the back of the plugs for color or function of wire
  • Wht - ground
  • red - stop
  • blue - accessory/aux
  • brown - tail
  • black - Marker
  • grn - left turn
  • yellow - right turn

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

06 grand prix stick in limp mode

DTC C0040 Right Front Wheel Speed Sensor Circuit --
Conditions for Setting the DTC
C0035 C0040 C0045 C0050
One of the following conditions exists for 0.02 seconds:
• A short to voltage in the wheel speed sensor signal circuit.
• An open in the wheel speed sensor signal circuit.

Diagnostic Aids
C0035 C0040 C0045 C0050
If the customer comments that the ABS indicator is ON only during moist environmental conditions (rain, snow, vehicle wash, etc.), inspect the wheel speed sensor wiring for signs of water intrusion. If the DTC is not current, clear all DTCs and simulate the effects of water intrusion by using the following procedure:
Spray the suspected area with a 5 percent saltwater solution. To create a 5 percent saltwater solution, add 2 teaspoons of salt to 354 ml (12 oz) of water.
Test drive the vehicle over various road surfaces (bumps, turns, etc.) above 40 km/h (25 mph) for at least 30 seconds.
If the DTC returns, replace the suspected wheel speed sensor or repair the wheel speed sensor wiring.
Rinse the are thoroughly when completed.


Replace the EBCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the repair?
0helpful
1answer

Hi, Have an 07 AWD Equinox, all stability control traction control, ABS, AWD, lights off, I've cleaned the ground ,all still on, now I have code c0040, c0899, wheel speed sensors are new, my scanner shows...

Do yourself a favor an take it to a qualified repair shop . You need a factory scan tool to see these code's
DTC C0040 00 : Right Front Wheel Speed Sensor Circuit No Additional Information
DTC C0040 0F : Right Front Wheel Speed Sensor Circuit Erratic Signal
DTC C0040 18 : Right Front Wheel Speed Sensor Circuit Signal Amplitude Less Than Minimum

DTC C0899: Device Voltage Low
Circuit/System Description
The electronic brake control module (EBCM) monitors the battery voltage level available for system operation. A low voltage condition prevents the system from operating properly.

Circuit/System Testing
Measure the voltage at the battery terminals.
With scan tool, read the battery voltage in the EBCM data list.
? If less than 10 volts, test the ground circuit of the EBCM for high resistance. If the circuit test normal, test or replace the EBCM.
Go to Battery Inspection/Test and Charging System Test .
0helpful
2answers

On grand prix2006 code C0040 which weel is that my computer tell me rear but no side

It is the right front (RF) ABS sensor that this codes corresponds to nothing to do with the rear.. Are you using a GM TECH 2 scanner? If not that is the problem.
0helpful
1answer

Have a 2004 gmc yukon getting codes c0040, c0550,c0455,c0296 in the abs computer. Trac and abs light on as well as suspension control.

C0040 - Right Front Wheel Speed Circuit Malfunction
C0550 - ECU Malfunction - internal write / checksum malfunction
C0455 - Either:
  • A bent terminal or poor connection at the SWPS may be one possible cause; or
  • The vehicle stability enhancement system (VSES) electronic brake control module (EBCM) calibration may be the other possible cause.
C0296 - Transfer Case Delivered Torque for Stability Control System Circuit
http://www.obd-codes.com/trouble_codes/obd-ii-c-chassis-codes.php
1helpful
2answers

Abs codes c0040 and c0041 front wheel speed control sensor and circuit

Will be located near the wheel hub. As long as there is no physical damage I would guess you will be replacing the sensor
0helpful
1answer

TC, ABS and Service brake assist lights are on after changing speed sensor.

make sure your sensor is aligned properly check your connections have you driven the car since you changed sometimes you need to drive the vehicle to reprogram the speed sensor into the abs circuit these are fused circuits check your fuses
2helpful
1answer

HOW TO REPLACE OR REPAIR WHEEL SPEED SENSOR

It is part of the bearing hub assembly.Very have to do without air tools,If setting multiple abs/tc code (wheel speed sensors) probably abs electronic module or chaffed wires on drivers side at ac lines by air box.Have big problems with this and probably will come back.
2helpful
1answer

I pulled the codes and here they are : C0036, C0035, C0040

Sounds like you need front wheel speed sensors. Replace the wheel bearings and sensors. May have an ABS unit fault, but more likely is both wheel bearings/speed sensors.
0helpful
1answer

ABS SERVICE LIGHT KEEPS COMMING ON, BUT BEFORE IT COMES ON I HEAR A CRUCHING SOUND WHEN I STOP. I replaced both of the front rotors and pads, and also I replaced driver and passenger side calipers. WHY IS...

Most likey you have a problem with one of the front wheel speed sensors not reading or a sensor harness.See if someone can pull a Code from you abs controller.Maybe a C0041.Very common on Relay Vans! If it has this code most likely will need a new set of twisted wires run from the EBTCM to the front wheel speed sensor.Hope This Helps
Not finding what you are looking for?

2,236 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...