Headlight bulb replacement for 2000 Caviler

Headlight Change 2006-2010 Mazda 5 - CarCareKiosk

www.carcarekiosk.com/video/2009_Mazda_5_Sport_2.../headlight

This free video shows how to change a burnt out headlight on a 2009 Mazda 5 Sport 2.3L 4 Cyl.. Complete instructions for replacing a head light bulb on a 2009 ...

Low beam head light bulb replace 2000-2006 Mazda Mpv ...

? 5:11
https://www.youtube.com/watch?v=kblzMLRJrok
Jun 29, 2013 - Uploaded by hp11208
Low beam head light bulb replace 2000-2006 Mazda Mpv .... My step dad and I successfully replaced a headlight yesterday! :-) ...I've lost it trying to replace the bulb. if anyone can let me know I would really appriciate it thanks ! ..... 5:00. Cleaning your IAC to fix rough idle on 2000 or 2001 Mazda MPV ...

Why dont you start by checking the fuses for headlights refer to your owners manual for the location of the fuse box for your car. if the fuses are good then replacing headlight bulbs to both headlight assembly is your next step.If after replacing both headlight bulb you still have the same problem then you might have other electrical issues.

1
Place the Mitsubishi on a flat service in park. Set the parking brake before continuing.

2Open the Galant's hood and locate the headlight cover -- roughly 3-inch wide circular piece of plastic -- behind the headlight bulb intended for replacement. Turn this cover clockwise to unlock it and pull it from the headlight assembly, exposing the headlight socket below it.

3

Hold the rear of the headlight socket and turn it counterclockwise to unlock it. Pull the headlight socket and bulb from the headlight assembly.

4

Grab the bulb and pull it from the socket with a slight wiggling motion.

5

Pick up the new 9003 headlight bulb using a clean, lint-free cloth and line up its prong with the slots in the socket. Never tough the bulb with your bare hands, as the oils left by your hands can cause the bulb to burn out prematurely.

6

Slide the socket and new bulb into the headlight assembly and turn the socket clockwise to lock it into place.

7

Place the plastic cover behind the bulb and turn it counterclockwise to lock it into place.

8

Repeat Steps 1 through 7 for the headlight bulb on the other side of the Galant, if needed.

9Close the Galant's hood.


Read more: How to Put in a Headlight Bulb on a 2000 Mitsubishi Galant ' eHow.com http://www.ehow.com/how_8210819_put-bulb-2000-mitsubishi-galant.html#ixzz27iQwCdOe

look inside owners manual in glove compartment look up bulb replacement in the back index it will show and tell you how to replace headlight bulbs. be sure to wear clean gloves, because headlight bulbs or halogen type bulbs, if oil from hands or skin touch the halogen bulb it will cause halogen light bulb overheat and blow out.you can go by auto parts store when you buy new headlight bulb the salesperson will go out to vechicle and replace headlight bulb for you wont charge you any thing.just charge you for the headlight bulb.

[Information] For a 2002 Toyota Camry, the Daytime Running Lights (DRL) operate utilizing the High Beams (inner Lamps closer to the center of the vehicle front) at a reduced power.

[The troubleshooting process:] Review the Owner's Manual and ensure the test configuration matches the following criteria:
1. According to the 2002 Toyota Camry Owner's Manual (Check your Owners Manual):
"The DRL system will make your headlights come on at a reduced brightness when:
The light switch s in the "DRL" position.
The ignition is on with the engine running.
The headlight switch is off.
The parking brake is released."

2. Set the Test Conditions according to Step 1 above.

3. Check the headlight bulbs to ensure they are not burned out. If one burns out, there is a fair chance that the other would have burned out at the same time. Replace as necessary. In this case, if the high beams operate, the DRLs should also operate.
4. Test the system, ensuring the step 1 conditions are set. (Engine running, Multi-function Switch on Turn Signals in "DRL" position, headlight switch off (repeating what the manual says -- it should be obvious that in the "DRL" position, the headlight switch should be off / do not have the switch positioned to "High Beam"), and the Parking Brake "off").
5. If DRL lights do not work, check the engine compartment Fuse and Relay Box. there is a 5 Amp DRL fuse -- replace it with the spare. Test (step 4).
6. If it does not work, swap around or replace relays -- there are three (3). Any one of them could be bad (stuck or burned out). Test (step 4).
7. Other less likely possible issues could be that the Multi-function Switch is broken or a connection / wire is broken. [Beyond the scope of this process.]

My problem was that the test configuration did not have the engine running and parking brake off - Step 1. Problem solved with much thought, repetitive tests on the vehicle and going back to the basics -- what does the Owner's Manual say and where are the applicable fuses and relays located?

Surprisingly, your owners manual is one of the best sources for information on headlight replacement and taillight replacement. I learned this a few years ago myself, it's the only repair instruction they put in a automobile owners manual.

Changing the headlight bulb is a little bitdifficult for those not familiar with the vehicle. Both the high and low beamsare encased in a sealed unit, which also contains the turn signal, parkinglights, and side reflector. To change a single headlight, the entire headlightcompartment must be removed from the car. Once you understand how to remove thesealed headlight unit from the car, replacing the bulb is relatively simple.Follow the steps below on how to change the headlamp bulb in this car. Removal 1. Open the hood of the Jeep and locate thelong, headlamp jackscrew. The screw is located almost directly above theheadlight unit and can be removed using a 7-mm socket wrench. This will allowyou to remove the bezel from the grill opening panel. Remove the three screwsattached to the retaining ring to the headlight console. The screws are locatedon the bottom front and side of the unit. In some models the screws have beenreplaced with ball-stud alignment posts, enabling you to remove the headlightunit by simply wiggling it loose. 3. Disconnect the headlamp bulb wireharness connector located at the front of the headlight unit. This is locateddirectly above and between the parking and turning bulbs. 4. Separate the sealed headlight unit fromthe vehicle; disconnect and replace the old bulb. The high beam is locatedtoward the center of the car. The low beam is the bulb on the outermost edge ofthe unit. This is how to Install 1. Reconnect the headlamp bulb's wireharness-connector. Then Replace the headlight unit in the headlight canister. Positionthe retaining ring back in its original position and install the three screwsagain. If you wiggled the unit out, ensure that it is replaced firmly. 2. Install the headlamp bezel by replacingthe 7-mm jackscrew on the inside of the hood. Make sure all connections aretight before starting the car and inspecting the replacement.

CHECK ENGINE ON. SOMETIMES THE EXHAUST FUMES SMELL BAD. TECHNICIAN RECOMMEDED TO REPLACE THE CATALYTIC CONVERTER. PLEASE ADVISE.
COROLLA 2000 120,000 MILES

There should be two long screws on top of the headlight assembly itself. Remove the screws, and pull the assembly out. This will give you room to get to the bulb.

inside the engine compartment directly behind the headlight it unscrews and pops out. then put it back in and retighten.