Power window windows want let up or down.

Replace the master switch assembly.

Rear Passenger Power Window Operation
The rear passenger power window switches receive battery voltage through the window lockout control circuit if the window lockout function is disabled. Ground for the rear passenger power window motors is supplied through normally closed up and down contacts of both the rear passenger power window switches and the driver power window switch. When the either rear passenger power window switch is placed in the down position, the power window motor down control circuit is switched to 12 volts and is applied to the down side of the rear passenger power window motor. Since the other side of the rear passenger power motor is connected to ground through the normally closed up contacts of both the rear passenger and driver power window switches, the window travels down. By placing the rear passenger power window switch in the up position, the polarity of the power window motor is reversed and the window travels up.
The rear passenger power windows can also be controlled from the driver power window switch.

Did you try pushing the lock out switch on the drivers master switch ?

Doesn't have fuse for power windows . Has circuit breaker ,
System circuit breaker (POWER WDWS Circuit Breaker 30A )
Those rarely go bad .
Power Windows System Components
The power window system consists of the following components:
• Window master switch
• Front passenger window switch
• LR window switch
• RR window switch
• Window motors in each of the doors
• System circuit breaker (POWER WDWS Circuit Breaker 30A)
Power Windows System Controls
The power windows system can be controlled by a power window up or down switch activation.
Driver Window Operation
When the ignition switch is in the RUN or ACCY position, or retained accessory power (RAP) is enabled and the window master switch is activated to the DOWN position, battery positive voltage is applied to the window motor causing the window to open. When the window master switch is activated to the UP position, battery positive voltage is applied to the window motor in the opposite direction and the window closes.
The window master switch also controls the front passenger, LR, and RR windows.
Express Down Feature
The driver window will travel to the fully down position when the window master switch is pressed past the first detent. Activating the window master switch to the UP position will cancel the express down feature.
Lockout Switch Feature
The window master switch has a lockout switch which disconnects the battery positive voltage to the LR and RR window switches, disabling them.
Individual Window Operation
When the ignition switch is in the RUN or ACCY position, or RAP is enabled and an individual window switch is activated to the DOWN position, battery positive voltage is applied to the window motor causing that window to open. When the individual window switch is activated to the UP position, battery positive voltage is applied to the window motor in the opposite direction causing that window to close.

The only way to find the problem would be to view wiring diagrams an test the electrical circuits with a volt meter .

It's not the BCM ,more then likely it's that windows switch .
Rear Door (LH or RH) REAR POWER WINDOW SWITCH LH OR RH OPERATION WINDOW UP When the rear power window switch LH or RH is pressed in the up position Power is supplied ? through rear power window switch LH or RH terminal 4 ? to rear power window motor LH or RH terminal 2. Ground is supplied POWER WINDOW SYSTEM GW-17 C D E F G H J K L M A B GW Revision: January 2005 2004 Pathfinder Armada ? through rear power window switch LH or RH terminal 5 ? to rear power window motor LH or RH terminal 1. Then, the motor raises the window until the switch is released. WINDOW DOWN When the rear power window switch LH or RH is pressed in the down position Power is supplied ? through rear power window switch LH or RH terminal 5 ? to rear power window motor LH or RH terminal 1. Ground is supplied ? through rear power window switch LH or RH terminal 4 ? to rear power window motor LH or RH terminal 2. Then, the motor lowers the window until the switch is released. MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OPERATION WINDOW UP When the main power window and door lock/unlock switch (rear LH) is pressed in the up position Power is supplied ? through main power window and door lock/unlock switch terminal 3 ? to rear power window switch LH terminal 3 ? through rear power window switch LH terminal 4 ? to rear power window motor LH terminal 2. Ground is supplied ? through main power window and door lock/unlock switch terminal 1 ? to rear power window switch LH terminal 2 ? through rear power window switch LH terminal 5 ? to rear power window motor LH terminal 1. Then, the motor raises the window until the switch is released. When the main power window and door lock/unlock switch (rear RH) is pressed in the up position Power is supplied ? through main power window and door lock/unlock switch terminal 5 ? to rear power window switch RH terminal 3 ? through rear power window switch RH terminal 4 ? to rear power window motor RH terminal 2. Ground is supplied ? through main power window and door lock/unlock switch terminal 7 ? to rear power window motor RH terminal 2 ? through rear power window switch RH terminal 5 ? to rear power window switch RH terminal 1. Then, the motor raises the window until the switch is released. WINDOW DOWN When the main power window and door lock/unlock switch (rear LH) is pressed in the down position Power is supplied ? through main power window and door lock/unlock switch terminal 1 ? to rear power window switch LH terminal 2 ? through rear power window switch LH terminal 5 ? to rear power window motor LH terminal 1. Ground is supplied ? to main power window and door lock/unlock switch terminal 3 ? through rear power window switch LH terminal 4 ? through rear power window switch LH terminal 3 ? to rear power window motor LH terminal 1. Then, the motor raises the window until the switch is released

Electronic control module controls the windows an power seats .
B+ voltage for power windows come's from a 25 amp circuit breaker .
Power Window System Components
The power window system consists of the following components:
• Driver Door Module (DDM)
• Passenger Door Module (PDM)
• Body Control Module (BCM)
• RR power window switch
• Window up and window down relays in each of the rear passenger window switches
• Window lockout switch
• Reversible power window motors in each of the doors (circuit breaker protected)
• LT DOOR CB 25A (System power for left windows)
• RT DOOR CB 25A (System power for right windows)

Power Window System Controls
The power window system will operate anytime the Retained Accessory Power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The DDM contains four power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the two front windows have three positions UP, Down and Express Down, while the switches for the rear windows have only two positions, UP and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a Class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has two positions Up and Down. Each of these switch positions is a direct input to the PDM.
The two rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a Class 2 message from the DDM, can control the set of relays which will activate the rear window motors.

Does your vehicle have memory seats ?
Taking your vehicle to a qualified repair shop an having the systems checked for DTC'S - diagnostic trouble code's should be the first step , unless you have a factory or professional type scanner that can read these code's
DTC B1023
DTC B1544, B1600, or B1605
DTC B1580, B1590, B1610, or B1620
DTC B1640 or B1645
DTC B1722
DTC B3808
DTC B3809
DTC B3819
DTC B3820
DTC B3821
DTC B3822
DTC B3823
DTC B3824
DTC B3825

Are all windows not working ? Two separate circuit breakers left & right . Both in rear fuse box . Fuse Block - Rear Beneath the left rear seat
Check for broken wires inside the rubber boot from body to doors.
Do you know about electronic control modules ?
The power window system consists of the following components:
?€¢
Driver door module (DDM)

?€¢
Passenger door module (PDM)

?€¢
Body control module (BCM)

?€¢
LR power window switch

?€¢
RR power window switch

?€¢
Window up and window down relays in each of the rear passenger window switches

?€¢
Window lockout switch

?€¢
Reversible power window motors in each of the doors (circuit breaker protected)

?€¢
LT DOOR CB 25A (System power for left rear window)

?€¢
RT DOOR CB 25A (System power for right rear window)

The power window system will operate anytime the retained accessory power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The DDM contains 4 power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the 2 front windows have 3 positions Up, Down and Express Down, while the switches for the rear windows have only 2 positions, Up and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has 2 positions Up and Down. Each of these switch positions is a direct input to the PDM.
The 2 rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a class 2 message from the DDM, can control the set of relays which will activate the rear window motors.

Check

They hooked into wiring they shouldn't have >
Power Window System Components
The power window system consists of the following components:
?€¢
Driver door module (DDM)

?€¢
Passenger door module (PDM)

?€¢
Body control module (BCM)

?€¢
LR power window switch

?€¢
RR power window switch

?€¢
Window up and window down relays in each of the rear passenger window switches

?€¢
Window lockout switch

?€¢
Reversible power window motors in each of the doors (circuit breaker protected)

?€¢
LT DOOR CB 25A (System power for left rear window)

?€¢
RT DOOR CB 25A (System power for right rear window)

Power Window System Controls
The power window system will operate anytime the retained accessory power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The DDM contains 4 power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the 2 front windows have 3 positions Up, Down and Express Down, while the switches for the rear windows have only 2 positions, Up and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has 2 positions Up and Down. Each of these switch positions is a direct input to the PDM.
The 2 rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a class 2 message from the DDM, can control the set of relays which will activate the rear window motors.

Which window switch ? RT DOOR CB-circuit breaker , do you know what a circuit breaker is ? 25A (System power for right rear window)
LT DOOR CB 25A (System power for left rear window
The power window system will operate anytime the retained accessory power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The DDM contains 4 power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the 2 front windows have 3 positions Up, Down and Express Down, while the switches for the rear windows have only 2 positions, Up and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has 2 positions Up and Down. Each of these switch positions is a direct input to the PDM.
The 2 rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a class 2 message from the DDM, can control the set of relays which will activate the rear window motors.


The power window system consists of the following components:
?€¢
Driver door module (DDM)

?€¢
Passenger door module (PDM)

?€¢
Body control module (BCM)

?€¢
LR power window switch

?€¢
RR power window switch

?€¢
Window up and window down relays in each of the rear passenger window switches

?€¢
Window lockout switch

?€¢
Reversible power window motors in each of the doors (circuit breaker protected)

?€¢
LT DOOR CB 25A (System power for left rear window)

?€¢
RT DOOR CB 25A (System power for right rear window)

If you not sure about any of this I suggest you take your vehicle to a ASE certified repair shop .

The power windows on your vehicle are controlled by an electronic control module , as are the power mirrors !
Power Window System Components
The power window system consists of the following components:
• Driver door module (DDM)
• Passenger door module (PDM)
• Body control module (BCM)
• LR power window switch
• RR power window switch
• Window up and window down relays in each of the rear passenger window switches
• Window lockout switch
• Reversible power window motors in each of the doors (circuit breaker protected)
• LT DOOR CB 25A (System power for left rear window)
• RT DOOR CB 25A (System power for right rear window)

Your best bet , take your vehicle to a qualified repair shop.

If they sound like they are trying to do something it's not the lock out switch . But to be sure pulling out the switch an testing for B+ voltage to and from the switch . Plus pull the other door switches to see if they have B+ voltage and good grounds would be the thing to do.. If you don't know how to check automotive electrical circuits your best bet , take it to a qualified repair shop .
Passenger Power Window Operation
The passenger power window switches incorporate window up and down relays. The relay coil feed and supply sides are powered through the RAP fuse supply voltage circuit. The normally closed contacts of each relay is connected to ground. The load side of each of the relays are connected to either side of the power window motor through the power window up and down circuits. The up and down relay control circuits are connected to the normally closed contacts of the passenger window switch. These contacts are wired in series with the power window master switch, through the power window master switch up and down signal circuits and then to ground when the power window master is placed in the up or down position. This allows for the up and down operation of the passenger power window from the power window master switch. The center pole of the passenger power window switch is also connected to ground and will energize the relay when placed in the up or down position.

Driver Power Window Operation
The driver power window is unique from the passenger power windows in that it does not use window up and down relays. The driver power window is operated directly from the power window switch.
The normally closed contacts of the switch are connected to ground and the center pole is connected to the RAP fuse supply voltage circuit. By placing the left power window switch in the down position, voltage is applied to the power window motor left front down circuit and to the power window motor. The other side of the power window motor is connected to ground through the normally closed contacts of the left power window switch through the power window motor left front up circuit and drives the window down.
By placing the left power window switch in the up position the polarity of the motor is reversed and the motor drives the window up.

Has circuit breaker for B+ power
• PWR WDO CB 25A (fuse block) (System power for left and right windows 2-door vehicles. System power for LF and LR windows 4-door vehicles)
• PWR WDO CB 25A (IP wiring harness junction block) (System power for RF and RR windows 4-door vehicles)

Could be passenger door switch .