Question about Cars & Trucks

1 Answer

Light Oil Reset 2007 mercury montego

How to reset oil change light after oil has been change

Posted by Anonymous on

Ad

1 Answer

ABurns

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 43 Answers
Ad

5 Related Answers

matney68

Donnie Matney

  • 426 Answers

SOURCE: reset oil change light

ok turn the key on and pump the gas pedal 3 times and it should flash and then go away.until next service time

Posted on Jul 02, 2009

Ad

Anonymous

  • 56 Answers

SOURCE: 2005 mercury montego message center

LOL!!! I had the same problem. I can't recall the exact steps, but there aren't that many options, so you'll get this. With the car running, press the Info button on the left side. It will cycle through the various statuses of the car. At one point, it will get to the Oil and will tell you something like "Press Reset if New." Press it and hold that darned button until it acknowledges that you changed the oil. It will reset that message from 0% to 100%. It took me a couple of tries to get that to reset. Just keep trying it till it resets. You'll get it.

Posted on Mar 02, 2009

Brian Anderson

  • 399 Answers

SOURCE: Oil change light

Look up the light on the part of your owners manual that explains what each idiot light is for on your dash. That should give you a page where more information on it is available. Part of that section should state that if maintenance is done by someone other then your Mercury dealer, then do the following to reset the light. That should take care of ya.

Good Luck

Posted on Dec 15, 2009

Molson02536

Harvey N Tawatao

  • 3854 Answers

SOURCE: How do you reset the change oil message on a 2007

Ford Explorer, Mercury Mountaineer, 2002-07
To reset CHANGE OIL SOON/OIL CHANGE REQUIRED message on the Message Center, press the SET UP control to access the System Check mode. Press and release the RESET button to display “OIL LIFE % HOLD RESET NEW” is displayed. Press and hold the RESET button for 2 seconds until “IF NEW OIL HOLD RESET” is displayed. Press and hold RESET button until “OIL LIFE SET TO 100%” is displayed.
Ford Five Hundred, Freestyle, Mercury Montego 2005-06 Tap the ODO/TRIP button to toggle the display between the odometer and trip odometer. Tap on the ODOiTRIP button again to toggle the display between the trip odometer and OIL LIFE % display. Press and hold the ODO/IRIP button for 2 seconds or more to display OIL LIFE 100%. Your oil life in now reset.

Posted on Jan 06, 2010

Anonymous

SOURCE: 2007 mercury montego motor is making a loud noise

I would hope you checked the oil level & for leaks
also,before coming here

Hopefully you haven't ruined the motor already,that noise
is the sign of possible serious damage

Posted on Dec 08, 2012

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i reset the oil change light in a 2003 olds alero


turn key on (dont start engine) floor gas pedal 3 times 1,2,3. turn key off, now start engine it should go off, if not try it again.

Aug 03, 2011 | 2003 Oldsmobile Alero

3 Answers

I had the oil changed but the change oil light is still on, how do i reset the computer? 2000 oldsmobile alero


How to Reset the Change Oil Light

After changing the engine oil, the system must be reset.

With the ignition key to ON, push the RESET button

located in the driver's side instrument panel fuse block. The

CHANGE OIL light will start to flash, press and hold the

RESET button again. The reset is complete when you hear
the chimes sound and the CHANGE OIL light goes out.

Oct 25, 2010 | 2000 Oldsmobile Alero

3 Answers

How to reset the oil life monitor


1994-99 BUICK LESABRE
CHANGE OIL SOON Light
1. CHANGE OIL SOON light will come on when engine oil has broken down enough to require changing. After changing oil, reset oil life display.
2. To reset light, turn ignition on. Open glove box to access oil reset button. Press and hold oil reset button in glove box for at least 5 seconds, but not longer
than 60 seconds. The CHANGE OIL SOON light will flash 4 times to indicate light has been reset.

May 14, 2010 | 1999 Buick LeSabre

4 Answers

How to reset the change oil light for a 2007 lincoln town car. Hitting reset button doesn't do it.


FIRST press and release the setup button to display oil life= xxx
then press and hold the reset button for about 2 sec it should then display oil life set to 100%
--------------------------------
Just pressing the reset button when the change oil light comes on while driving will not reset the computer

Feb 15, 2010 | 2007 Lincoln Town Car Signature Limited...

3 Answers

How do i reset my oil light? my husband changed


TURN THE IGNITION KEY TO RUN WITH THE ENGINE OFF.FULLY PRESS AND RELEASE THE ACCELERATOR PEDAL THREE TIMES WITH IN FIVE SECONDS.YOU HAVE TO DO THIS MORE THAN ONE TIME.ITS NOT GOING TO RESET FIRST TRY BUT DO THIS PROCEDURE.UNTIL THE CHANGE ENGINE OIL LIGHT WILL FLASH WHILE THE SYSTEM IS RESETTING.TURN THE KEY TO OFF.WAIT A FEW SECONDS.START CAR UP TO SEE IF CHANGE OIL LIGHT COME BACK ON.IF YES YOU HAVE TO TRY THE RESET PROCEDURE AGAIN.

Sep 26, 2009 | 2006 Chevrolet Equinox

2 Answers

How to reset the change oil light for lincoln town car 2007


Press setup on message center,
press select for system check,
At oil life, press reset

Aug 14, 2009 | 2007 Lincoln Town Car Signature Limited...

3 Answers

How do I reset the change oil soon light?


Hi to reset the oil life monitor
turn the key on engine off
push the gas pedal to the floor 3 TIMES WITH IN 5 SECONDS
the light will flash then go out

May 12, 2009 | 2005 Chevrolet Equinox

3 Answers

2006 ford exsplorer oil light did not go off after a oil change.


In the owners manual, you will find reset procedures.

I found this for ya, hope it helps!

Please Rate!

Oil Change Reset
A press of the OIL CHANGE RESET switch will allow you to
reset the oil life feature to 100% (or your Personalized Oil Reset
Percentage). After you have the oil changed, you must execute
the following procedure. Press the OIL CHANGE RESET switch
and hold for five seconds as the M/C counts down for five
seconds. After a successful reset the Message Center will display
“OIL LIFE RESET TO 100%.” If you have established a
Personalized Oil Reset Percentage, the display will show that
percentage instead of 100%. To ensure accurate oil life
indicators, perform this reset procedure only after an oil change.
Your Personalized Oil Reset Percentage allows you to establish a
smaller oil change interval than the manufacturer’s
recommended interval. To establish your Personalized Oil Reset
Percentage perform the following procedure:
1. Press and hold the OIL CHANGE RESET switch and press
the RESET switch while the display is still counting down
the 5 seconds to reset. The display will change to “START
OIL LIFE AT XXX%.”
2. Press the OIL CHANGE RESET switch until the displayed
percentage is the Personalized Oil Reset Percentage that you
desire. Your choices are 100%, 90%, 80%, 70%, 60%, 50%,
40% and 30%.

Mar 03, 2009 | 2006 Ford Explorer

1 Answer

Change oil light reset?


Hi Shady, here is the procedure for resetting the light.
Resetting Procedure
Follow this procedure to reset the GM Oil Life System™
  1. Turn the ignition to RUN, with the engine off.
  2. Fully press and release the accelerator pedal three times within five seconds.
  3. If the CHANGE OIL SOON light flashes, the system is resetting.
  4. Turn the key to OFF after the light has finished flashing, then start the vehicle.
  5. If the CHANGE OIL SOON light comes back on, the engine oil life system did not reset. Repeat the procedure.
With Trip Computer
  1. Press the MODE button until the light appears next to OIL LIFE.
  2. Press and hold the RESET button for three seconds. The oil life percentage should change to 100 percent.

Nov 02, 2008 | 2002 Pontiac Grand Prix

3 Answers

2006 Ford Explorer "Oil Change Required" light is still on after changing the oil


IF YOU FIND THIS INFO USEFUL PLEASE RATE ME AS A FIXYA! THANKS

Oil Change Reset
A press of the OIL CHANGE RESET switch will allow you to
reset the oil life feature to 100% (or your Personalized Oil Reset
Percentage). After you have the oil changed, you must execute
the following procedure. Press the OIL CHANGE RESET switch
and hold for five seconds as the M/C counts down for five
seconds. After a successful reset the Message Center will display
“OIL LIFE RESET TO 100%.” If you have established a
Personalized Oil Reset Percentage, the display will show that
percentage instead of 100%. To ensure accurate oil life
indicators, perform this reset procedure only after an oil change.
Your Personalized Oil Reset Percentage allows you to establish a
smaller oil change interval than the manufacturer’s
recommended interval. To establish your Personalized Oil Reset
Percentage perform the following procedure:
1. Press and hold the OIL CHANGE RESET switch and press
the RESET switch while the display is still counting down
the 5 seconds to reset. The display will change to “START
OIL LIFE AT XXX%.”
2. Press the OIL CHANGE RESET switch until the displayed
percentage is the Personalized Oil Reset Percentage that you
desire. Your choices are 100%, 90%, 80%, 70%, 60%, 50%,
40% and 30%.

Oct 15, 2008 | 2006 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

john h

Level 3 Expert

23504 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6487 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...