2007 Lexus driver door will not lock.

I have read this 6 times and still not sure what the issue is? I have a 2005 ES330. To open all the doors with the key fob, you have to double press the Unlock Button. Pressing the Unlock button once, only opens the driver door.

The door lock module and further help is in the link.

https://www.google.com/search?q=2003+lexus+rx300.+door+lock+module+location

The Club Lexus forums are a great resource.

RX 300 Power Door Locks problem

ClubLexus https://www.clublexus.com > rx-1st-gen-1999-2003
Jun 24, 2008 - Door lock actuator relay/motor seems likely culprit. It has been discussed in the past. Try the search function. Although a different model, I ...

Power door lock switch do not unlock/lock driver's door.
Aug 1, 2007
03 RX300: Front driver side door lock not working - ClubLexus
Aug 12, 2010
Power door lock relay location? - Lexus Forum Discussion
Nov 6, 2013
RX300 door locks intermittent - Lexus Forum Discussion
Jul 30, 2011
More results from www.clublexus.com

..

I can help you with the drivers door. Simply put a screwdriver in the hole between outer door edge and lock mechanism. Push mechanism towards inside of door. The reverse of what happened when you accidentally locked the mechanism. I have done the same thing

if all other doors work the door lock actuator needs replaced most likely. if door switch works the same. if not then it could be a bigger problem in the circuit or remote control module. use a meter to test for signal to lock actuator. if no signal then ck control unit. if signal replace lock actuator.

needs a new drivers door lock

are you sure the battery is good in the remote? if so try putting the key in the driver door lock and locking and unlocking the doors three times in a row. if this dosent work i suggest taking it to an experienced lexus shop.

have you door lock module and the the brain in the key one of those is your problem have them check

1. sitting in driver seat, with driver's door OPEN, press lock/unlock button ON THE DRIVERS DOOR to lock all doors, then manually unlock driver door only.
2. Insert YOUR key in ignition, DO NOT TURN, then remove key.
3. Using the same lock/unlock button ON THE DRIVERS DOOR, slowly press lock-unlock in 5 cycles
4. Shut door.
5. Open door.
6. Using the same lock/unlock button ON THE DRIVERS DOOR, again slowly press lock-unlock in 5 cycles
7. With the door open insert your key into the ignition, turn to 'on' position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once by herself). If they don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second, then release the button. The locks should cycle once. If not, start over and go slower.
10. Close the door.
11. Open the door.
12. Press the lock button on the remote. The locks should do a lock-unlock cycle.
13. Close the door
14. Press the lock button on the remote, the doors should lock.
15. Press unlock button and the doors should unlock.

1. sitting in driver seat, with driver's door OPEN, press lock/unlock button ON THE DRIVERS DOOR to lock all doors, then manually unlock driver door only.
2. Insert YOUR key in ignition, DO NOT TURN, then remove key.
3. Using the same lock/unlock button ON THE DRIVERS DOOR, slowly press lock-unlock in 5 cycles
4. Shut door.
5. Open door.
6. Using the same lock/unlock button ON THE DRIVERS DOOR, again slowly press lock-unlock in 5 cycles
7. With the door open insert your key into the ignition, turn to 'on' position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once by herself). If they don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second, then release the button. The locks should cycle once. If not, start over and go slower.
10. Close the door.
11. Open the door.
12. Press the lock button on the remote. The locks should do a lock-unlock cycle.
13. Close the door
14. Press the lock button on the remote, the doors should lock.
15. Press unlock button and the doors should unlock.

Long beep to follow if successful.

Remote Programming Instructions

1. Driver's door OPEN and unlocked, all other doors closed and locked.

2. Insert YOUR key in ignition, DO NOT TURN, remove key.

3. Using the MANUAL lock/unlock button ON THE DRIVERS DOOR, slowly press lock and unlock 5 times (count the lock 5 times and unlock 5 times).

4. Shut door.

5. Open door.

6. Using the lock/unlock button ON THE DRIVERS DOOR, slowly press lock and unlock 5 times (count the lock 5 times and unlock 5 times).

7. With the door open insert your key into the ignition, turn to on position (DON'T START), wait 5 seconds. Turn off and remove key.

8. Locks should cycle once (Car will lock and then unlock once). If they don't cycle or they cycle more than once, do steps 1-7 over.

9. Now using the remote, push lock button, hold for one second,
release. The locks should cycle once. If not, start over and go slower.

10. Close the door. Open the door. Press the lock button on the remote. The locks should cycle. Close the door. Press the lock button on the remote, the doors should lock. Press again and the doors should unlock.

try this:

1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.
2. Insert key into the ignition (DO NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.
4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.
5. Press any button on remote for a minimum of 1 second.
System should now lock and unlock doors once.

6. Close and open drivers door.
7. Press any button on remote for a minimum of 1 second. System should now lock and
unlock doors. Once to confirm programming, twice to indicate programming failed.
8. Repeat steps 5, 6 and 7 for additional remotes.