1991 pontiac 2.5 tech 4 fuel pump relay wont energize

Appears to be passenger side under the dash, #2 in the picture.

DTC P025A: Fuel Pump Flow Control Module Enable Circuit
The engine control module (ECM) supplies voltage to the fuel pump flow control module (FPCM) when the ECM detects that the ignition is on. The voltage from the ECM to the FPCM remains active for 2 seconds, unless the engine is in crank or run. While this voltage is being received, the FPCM closes the ground switch of the fuel pump and also supplies a varying voltage to the fuel tank pump module in order to maintain the desired fuel rail pressure.
Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the FPCM.
2. Ignition OFF, install a test lamp between the control circuit terminal 13 and ground.
3. Ignition ON, verify that a test lamp illuminates for 2 seconds.
?‡'
If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.

4. If all circuits test normal, replace the FPCM.

Relay for what ? Which engine do you have LY6 or non LY6

The fuel pump control module is controlled by the ECM - engine control module , Possibility of DTC'S stored ! You need to take to Chevy Dealer !
The engine control module (ECM) supplies voltage to the fuel pump control module (FPCM) when the ECM detects that the ignition is ON. The voltage from the ECM to the FPCM remains active for 2 seconds, unless the engine is in Crank or Run. While this voltage is being received, the FPCM closes the ground switch of the fuel pump and also supplies a varying voltage to the fuel tank pump module in order to maintain the desired fuel rail pressure.

The fuel pump relay controls the pump most relays have 4 pins 2 are the controlling circuits usually ignition feed and the ecm controlling the ground side when energized (grounded) the coil closes a set of contacts usually battery positive and the controlled item in this case the fuel pump. problems on the controlling side open circuit shorted circuit controlling side bad contacts stuck closed or open.

Please stop replacing parts it costs money!
Go get a timing light to see if you have spark if you do not it is a bad ignition module.
to check your fuel pump connect a fuel pressure guage to the engine fuel injector rail and turn over the engine the pressure should be: 40 to 60 psi.

Here is the definition for the code.
Test procedures are a little different depending on the make and model.

P0232 Description The Engine Control Module (ECM) provides ignition positive voltage to the coil side of the fuel pump relay. When the ignition switch is first turned ON, the ECM energizes the fuel pump relay, which applies power to the fuel pump. The ECM enables the fuel pump relay as long as the engine is cranking or running, and crankshaft reference pulses are received. If no crankshaft reference pulses are received, the ECM de-energizes the fuel pump relay after 2 seconds. The ECM monitors the voltage on the fuel pump relay control circuit.

Read more: http://engine-codes.com/p0232.html#ixzz2KX7eZdtR

The first things I need to know are which engine do you have, and what have you actually tested so far ?
If it has no power or ground pulse to the injectors and no spark, the problem would be something that controls both such as a crank or cam sensor. Or a relay. Or the ignition module. And so on.

P0230 - Fuel Pump Primary Circuit Malfunction Symptoms - Engine Light ON (or Service Engine Soon Warning Light) Possible causes - Blown Fuel Pump fuse
- Open Fuel Pump Monitor Circuit
- Faulty Fuel Pump Relay
- Damaged ECM. P0230 Description The Engine Control Module (ECM) provides ignition positive voltage to the coil side of the fuel pump relay. When the ignition switch is first turned ON, the ECM energizes the fuel pump relay, which applies power to the fuel pump. The ECM enables the fuel pump relay as long as the engine is cranking or running, and crankshaft reference pulses are received. If no crankshaft reference pulses are received, the ECM de-energizes the fuel pump relay after 2 seconds. The ECM monitors the voltage on the fuel pump relay control circuit.
Please go to this LINK for P0300 diagnosis.

if there is no power to the fuel pump check relays and fuses....UNDERHOOD FUSE & RELAY PANEL IDENTIFICATION Fig. 2: Underhood Fuse & Relay Panel Identification Courtesy of ISUZU MOTOR CO. Fusible Link Identification ? A - 80 Amp (1991-92 3.1L) ? A - 60 Amp Main-1 ? B - 30 Amp Main-2 ? C - 30 Amp (1993-94) ECM (3.2L) ? D - 30 Amp Condenser Fan (A/T Models) Relay Identification ? 1 - Headlight Relay ? 2 - A/C - Heater Relay ? 3 - Starter Relay ? 4 - A/C Compressor Relay ? 5 - Charge Relay ? 6 - Fuel Pump Relay ? 7 - ECM Relay ? 8 - Wiper Relay Fuse & Circuit Breaker Identification ? 1 - 15 Amp (1991) ECM, Fuel Injection System ? 1 - 15 Amp (1992-94 2.6L) ECM, Fuel Injection System ? 1 - 10 Amp (1992-94 3.1 & 3.2L) Heated Oxygen Sensor, Fuel Injection System ? 2 - 20 Amp (1991-92) Fuel Pump ? 2 - 20 Amp (1993-94 2.6L) Fuel Pump ? 2 - 15 Amp (1993-94 3.2L) Fuel Pump ? 3 - 10 Amp (1991) ? 3 - 15 Amp (1992-94) Turn Signal Lights, Hazard Warning Flasher Lights ? 4 - 10 Amp Horn, Door Locks ? 5 - Not Used (1991 3.1L) ? 5 - 10 Amp Charging System, Charge Warning Light WARNING: Always disconnect battery ground cable before servicing "high- current fuses. It is recommended that "high-current" fuses be replaced by a qualified technician. Page 1 of 2 FUSES & CIRCUIT BREAKERS -1994 Isuzu Rodeo LS? 6 - Not Used (1991) (1992-93 2.6L) ? 6 - 10 Amp (1992-94 3.1L & 3.2L) A/T Interlock System ? 6 - 10 Amp (1994 2.6L) Heated Oxygen Sensor, Fuel Injection System ? 7 - 20 Amp Heater/Air Conditioning Blower Controls ? 8 - 10 Amp Air Conditioner Compressor Controls ? 9 - 10 Amp Right Headlight ? 10 - 10 Amp Left Headlight © 2008 Mitchell Repair Information Co., LLC.

Underhood fuse block swap out relay #7 thats the ECM relay.
Ground Circuits Using a DVOM, touch negative voltmeter lead to a good ground. Touch positive voltmeter lead to each ground terminal. With vehicle running, voltmeter should indicate less than one volt. If reading is greater than one volt, check for open, corrosion and loose connection on ground lead. See ECM GROUND LOCATION table for ECM ground location.
Page 1 of 1 SYSTEM/COMPONENT TESTS - 2.6L EFI -1994 Isuzu Rodeo

I think this code is defined as follows:
Fuel pump circuit fault or Mixture Control (M/C) solenoid fault or Electronic Control Module (ECM) fault/EGR solenoid #2 failure
Check your fuel pump relay as well - this could be the fault in the fuel pump circuit.
Hope this helps, Sherwin