Question about 2001 Chrysler Concorde

1 Answer

How do i reset the timing on 2001 2.7l concorde if the chain was replaced and the timing is off

Got new chain and water pump on car now my timing is off. I got the right side at tds where should the other side be.

Posted by jacobwbstr on

Ad

1 Answer

alloverads

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 16 Answers

Did you take pictures while removing the originals? It's always a good habit. Below are the instructions you need to follow. Your own pics are very helpful when doing a big job like this.

  1. Disconnect negative battery (1) cable.
  2. Drain cooling system.
  3. Remove upper intake manifold.
  4. Remove cylinder head covers, crankshaft vibration damper, and timing chain cover.
CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage.
how do i reset the timing on 2001 2.7l concorde if - 117014297

  1. Align crankshaft sprocket timing mark to mark on oil pump housing (2). The mark on oil pump housing is 600 ATDC of #1 cylinder.
CAUTION: When the timing chain is removed and the cylinder heads are still installed, DO NOT rotate the camshafts or crankshaft without first locating the proper crankshaft position. Failure to do so will result in valve and/or piston how do i reset the timing on 2001 2.7l concorde if - 117016938r>117016938

  1. Remove primary timing chain tensioner retainhow do i reset the timing on 2001 2.7l concorde if - 117016939) and tensioner (1) from right cylinder head.
117016939

  1. Disconnect and remove camshaft position sensor (4) from left cylinder head.
  2. Remove timing chain guide access plugs (3) from cylinder heads.
NOTE: When camshaft sprocket bolts are removed, the camshafts will rotate in a clockwise direction.
  1. Starting with the right camshaft sprocket, remove the sprocket attaching bolts. Remove camshaft damper (1) (if equipped) and sprocket.
  2. Remove left side camshaft sprocket attaching bolts and remove sprocket.
  3. Remove lower chain guide (7) and tensioner arm (8).
  4. Removehow do i reset the timing on 2001 2.7l concorde if - 117016940ary timing chain (5).
  5. Remove crankshaft sprocket (6).
INSTALLATION
117016940

  1. Inspect all sprockets (4,9,11) and chain guides (2,5,10). Replace if worn.
  2. For crankshaft sprocket installation procedures Refer to CRANKSHAFT SPROCKET.
  3. If removed, install right and left side short chain guides (11). Tighten attaching bolts to 28 Nm (250 inch lbs.) .
  4. Align crankshaft sprocket timing mark to the mark on oil pump housing (3).
NOTE: Lubricate timing chain and guides with engine oil before installationhow do i reset the timing on 2001 2.7l concorde if - 117016941
  • Place left side primary chain sprocket onto the chain so that the timing mark is located in-between the two (plated) timing links (1).
  • 117016941

    1. Lower the primary chain with left side sprocket through the left cylinder head opening.
    NOTE: The camshaft sprockets can be allowed to float on the camshaft hub during installation.
    1. Loosely position left side camshaft sprocket over camshaft hub.
    2. Align timing (plated) link to the crankshaft sprocket timing mark (3).
    3. Position primary chain onto water pump drive sprocket (10).
    4. Align right camshaft sprocket timing mark to the timing (plated) link on the timing chain (8) and loosely position over camshaft hub.
    5. Verify that all chain timing (plated) links are properly aligned to the timing marks on all sprockets.
    6. Install left side lower chain guide (2) and tensioner arm (5). Tighten attaching bolts to 28 Nm (250 inch lbs.) .
    NOTE: Inspect O-ring on chain guide access plugs before installing. Replace O-ring as necessary.
    1. Install chain guide access plugs to cylinder heads. Tighten plugs to 20 Nm (15 ft. lbs.) .
    NOTE: To reset the primary timing chain tensioner, engine oil will first need to be purged from the tensioner.
    117016942

    1. Purge oil from timing chain tensioner using thhow do i reset the timing on 2001 2.7l concorde if - 117016943ng procedure:
      1. Place the check ball (2) end of tensioner into the shallow end of Special Tool 8186 (3).
      2. Using hand pressure, slowly depress tensioner until oil is purged from tensioner.
    117016943

    1. Reset timing chain tensioner using the following procedure:
      1. Position cylinder plunger (4) into the deeper end of Special Tool 8186 (3).
      2. Apply a downward force until tensioner is reset.
    NOTE: If oil was not first purged from the tensioner, use slight finger pressure to assist the center arm pin of Special Tool 8186 to unseat the tensioner's check ball.

    CAUTION: Ensure the tensioner is prhow do i reset the timing on 2001 2.7l concorde if - 117016944set. The tensioner body (4) must bottom against the top edge of Special Tool 8186 (3). Failure to properly perform the resetting procedure may cause tensioner jamming.

    NOTE: Inspect the tensioner O-ring (2) for nichow do i reset the timing on 2001 2.7l concorde if - 117016945s and make sure the snap ring (1) is correctly installed, replace as necessary.
    117016944

    1. Install the reset chain tensioner (1) into the right cylinder head.
    2. Position tensioner retaining plate (2) and tighten bolts (1) to 12 Nm (105 inch lbs.) .
    117016945

    1. Starting at the right cylinder bank, first position the camshaft damper (1) (if equipped) on camshaft hub, then insert a 3/8 square drive extension with a breaker bar into intake camshaft drive hub. Rotate camshaft until the camshaft hub aligns to the camshaft sprocket and damper attaching holes. Install the sprocket attaching bolts and tighten to 28 Nm (250 inch lbs.) .
    2. Turn the left side camshaft by inserting a 3/8 square drive extension with a breaker bar into intake camshaft drive hub and rotate camshaft until the sprocket attaching bolts can be installed. Tighten sprocket bolts to 28 Nm (250 inch lbs.).
    3. Rotate engine slightly clockwise to remove timing chain slack, if necessary.
    117016946

    1. Activate the timing chain tensioner by using a flat bladed pry tool to gently pry tensioner arm towards the tensioner slightly. Then release the tensioner arm. Verify the tensioner is activated (extends).
    117016947

    1. Install camshaft position sensor (2) and connect electrical connector.
    2. Install the timing chain cover, crankshaft vibration damper, and cylinder head covers.
    3. Install upper intake manifold.
    NOTE: After installation of a reset tensioner, engine noise will occur after initial start-up. This noise will normally disappear within 5-10 seconds.
    1. Fill cooling system.

    Posted on Sep 25, 2013

    Ad

    5 Related Answers

    garyq1970

    Gary Queen

    • 85 Answers

    SOURCE: how do i set the timing on a 2000 chrystler concorde 2.7?

    0900c15280040a4e.jpgHope this helps.. If you have any questions or did not get diagram... (sometimes happens) feel free to contact me


    1. Install the timing belt tensioner and tighten the retaining bolts to 17 ft. lbs. (24 Nm), but do not remove the pin at this time.
    2. Check that all timing marks are still aligned.
    3. Use bulldog clips (large paper binder clips) or other suitable tool to secure the timing belt and to prevent it from slacking. Install the timing belt. Starting at the crankshaft, go around the idler pulley, then the front camshaft sprocket, the water pump pulley, the rear camshaft sprocket and the tensioner pulley.
    4. Be sure the belt is tight between the crankshaft and front camshaft sprocket, between the camshaft sprockets and the water pump. Gently raise the tensioner pulley, so that the belt does not sag, and temporarily tighten the center bolt.
    5. Move the crankshaft 1/4 turn counterclockwise, then turn it clockwise to the position where the timing marks are aligned.
    6. Loosen the center bolt of the tensioner pulley. Using MD998767 tensioner tool, and a torque wrench apply 3.3 ft. lbs. (4.4 Nm) tensional torque to the timing belt and tighten the center bolt to 35 ft. lbs. (48 Nm). When tightening the bolt, be sure that the tensioner pulley shaft does not rotate with the bolt.
    7. Remove the tensioner plunger pin. Pretension is correct when the pin can be removed and installed easily. If the pin cannot be easily removed and installed it is still satisfactory as long as it is within its standard value.
    8. Check that the tensioner pushrod is within the standard value. When the tensioner is engaged the pushrod should measure 0.149–0.177 in. (3.8–4.5mm).
    9. Rotate the crankshaft two revolutions and check the timing marks. If the timing marks are not properly aligned remove the belt and repeat Steps 17 through 23.
    10. Install the timing belt covers.
    11. Install the engine mounting bracket.
    12. Lower the engine enough to install the engine mount onto bracket and remove the floor jack.
    13. Install the power steering pump bracket and pump.
    14. Install the crankshaft pulley and tighten the retaining bolt to 13 ft. lbs. (18 Nm).
    15. Install the accessory drive belts.
    16. Properly fill the cooling system.
    17. Connect the negative battery cable.
    18. Check for leaks and proper engine and cooling system operation.

    Posted on Nov 14, 2008

    Ad

    Anonymous

    • 247 Answers

    SOURCE: 96 chrysler concorde water pump replace

    what was your response again?

    Posted on Jan 07, 2009

    Anonymous

    • 6 Answers

    SOURCE: replacing the water pump

    all i can really tell you is that this really difficult, because the pump is in the timing cover.

    Posted on May 21, 2009

    wade dunlap

    • 101 Answers

    SOURCE: chrysler wont start

    Sounds like a short maybe. maybe the wire completely broke? if you know a technician, see if the fuel pump is even getting power when key is on

    Posted on Jul 02, 2009

    Anonymous

    • 242 Answers

    SOURCE: adjusting the timing chain on a 02 concorde

    Timming chains are not adjustable.

    Posted on Sep 04, 2009

    Add Your Answer

    ×

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    How to replace timing chain on 2001 dodge intrepid 2.7


    It's a BIG job. It requires removing everything from the top of the engine (intake manifold, throttle body, all plumbing, valve covers) then removing the harmonic damper, most of the accessories, and then the timing cover. That's just to get to the timing chain. You have to remove the chain guides and tensioner, then cam gears and crank gear. If you're going this route, also replace the two chains (intake cam to exhaust cam) on top of the heads, the water pump, and the tensioners. Be very precise in reinstalling the three timing chains so that everything is in time.
    The link shows the details of the chain itself, but be aware that your engine is packed into your Intrepid with limited work space in some areas.
    Chrysler Sebring Concorde 300 2 7L timing replacement Cloyes kit 9 0397SA

    Aug 20, 2017 | Dodge Cars & Trucks

    2 Answers

    I just changed water pump and timing slides on my 99 concorde and now i have no spark


    Please check that during the process of replacement you could have snapped a wire or connector.
    It is best to check on the related area with a good lighting as there is a possibility that the power to the ignition unit has snapped.
    Also check if the fuse has blown on the IGN section.

    Jul 26, 2012 | 1999 Chrysler Concorde

    1 Answer

    How do I replace the waterpump 2000 chrysler concorde engine 2.7. Doe the timeing belt need to be readjusted?


    The 2.7 L is a chain driven DOHC engine. No belt. Chain should last the life of the engine.
    The 2.7 also has a "bad reputation" for going bad - but this is in almost all cases due to the oil change intervals. Change oil every 5,000 miles and sludge won't build up. Don't change the oil and about 15,000 to 25,000 miles later, <boom> bye bye engine.
    Not sure where the water pump is. Never had to replace one yet.

    Nov 04, 2011 | 2000 Chrysler Concorde

    1 Answer

    I had to replace the water pump in 96 chrysler concord now the timing is off, how do i reset the timing


    the only way is to remove the belt and do it again, because there is no adjustment on ignition timing

    Apr 13, 2010 | 1996 Chrysler Concorde

    1 Answer

    Making clicking sounds while idling. goes away while driving. changed tensioner arm fortiming chain. Car started overheating. Changed water pump now sound is back. Mecahic cannot figure out what sound is....


    u have to check chain for slack if ther is lots slak change if not try to change oil and replace with haver oil and add can lucas u may have lifter noise or worn roker arms

    Nov 25, 2009 | 2000 Chrysler Concorde

    1 Answer

    How to replace water pump on 2.4 chevy cavalier


    This is a job for the dealer or cerified mechanic. The front cover and timing chain needs to be remove to access the water pump mounted behind the engine. The pump is driven by the timing chain and timing will need to be reset using special tools.

    Jul 20, 2009 | 1998 Chevrolet Cavalier

    1 Answer

    Replacing the water pump


    all i can really tell you is that this really difficult, because the pump is in the timing cover.

    May 21, 2009 | 2003 Chrysler Concorde

    4 Answers

    Water leak next to block behind water pump.


    i have a 1999 ford explorer v8 5.0 and it is leaking right behind the waterpump. but not from the pump, about 5 inches behind the pump, like by the block, what is it?

    Apr 25, 2009 | Ford F-150 Cars & Trucks

    2 Answers

    2000 Chrysler Concorde


    Fuel filter, throttle position sensor. Check these items

    Feb 16, 2009 | 2000 Chrysler Concorde

    Not finding what you are looking for?
    2001 Chrysler Concorde Logo

    685 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    Marvin
    Marvin

    Level 3 Expert

    85239 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    14850 Answers

    Mike

    Level 3 Expert

    4369 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...