Question about 2000 Chevrolet Tahoe
When i turn the key its trying to start and the belt is moveing and the fan is moving slowly but not starting all the way
SOURCE: 2008 Chevy Cobalt - care
replace the shifter assembly.I replace alot of them.use this bulletin as a reference.Subject: Various Concerns With Shifter and/or Ignition Key (Replace Shifter Assembly/Shifter Components or Ignition Lock Cylinder )
Models: 2005-2008 Chevrolet Cobalt
2005-2006 Pontiac Pursuit (Canada Only)
2007 Pontiac G5
with Automatic Transmission 4T45-E (RPO MN5)
Some customers may comment on any of the following concerns:
• The shifter is hard to move or binds.
• They cannot remove the ignition key.
• It takes high effort to rotate the key.
The shifter button may be sticking in the handle.
The pin that activates the micro-switch may have moved out of position (refer to illustration above). This causes the micro-switch to fail to engage when the vehicle is placed in Park. If this condition is present, the customer will not be able to remove the key from the ignition.
The illustration above shows the switch in a correct position.
Metal flashing left in the cylinder may cause a high effort to rotate the key.
The slider may be binding in the guides. This may cause the shifter to become difficult to operate.
Verify that the shifter button is inoperative by evaluating if the park pawl pin on the shifter assembly moves when activating the button. If the parking pawl does not move when the button is activated, the shifter handle will have to be replaced. Refer to Floor Shifter Control Knob Replacement in SI.
Important: A change has been made to the shifter assembly for service. The replacement shifter assembly will read PRNDIL (Park, Reverse, Neutral, Drive, Intermediate and Low).
Verify that the micro switch is out of position. Replace the shifter assembly. Refer to Transmission Control Replacement in SI.
Important: Refer to instruction sheet that is supplied with the lock cylinder kit. BO 47869 is an essential staking tool and must be used for the repair.
Replace the ignition lock cylinder. Refer to Ignition Lock Cylinder Replacement in SI.
Replace the slide indicator and guides in the shifter following the procedure below:
Apply the parking brake.
Remove the upper console trim. Refer to Trim Plate Replacement-Console Front in SI.
Remove shifter knob. Refer to Floor Shifter Control Knob Replacement in SI.
Remove the indicator plate. Use a flat-bladed screwdriver to release the locking tabs.
Remove the shifter indicator lens.
Pull up on the indicator and remove it from the assembly.
Remove the two front rails by unsnapping the front and lifting up, and then back, to remove the rails from the shifter assembly.
Install the new guides. Place the hook end into the assembly and push down. It will snap into place.
Install the new slide indicator. With the transmission in neutral, place the slide over the shifter and into the guides. Move the slide indicator down the guides in the front and rear.
Important: Replace the shifter indicator lens if damage is present due to the slider binding or if it becomes damaged during disassembly.
Install the shift indicator lens.
Install the shift indicator plate.
Install the shifter knob. Refer to Floor Shifter Control Knob Replacement in SI.
Install the upper console trim. Refer to Trim Plate Replacement-Console Front in SI. post back with what you find.
Posted on Jan 20, 2009
It sounds like it just needs to be reinitialized. Turn your key to the on position with motor off and hold the up/full vent button down for at least 30 seconds or until your sunroof either clicks or goes to the full vent position. That should fix your problem.
Posted on Jun 25, 2009
If the noise is present when the car is not moving, It would seem it must be the fuel pump, which is located in the gas tank. There isn't anything else at the back of the car that could make a sound w/out the car moving.
Posted on Nov 20, 2009
Testimonial: "thanks for the good info!"
you are probably correct. there are two contacts on the level sensor that wear out, which gives you the fluctuating gauge.
Posted on Feb 24, 2010
Tips for a great answer:
Jul 10, 2014 | 2000 Chevrolet Tahoe
Dec 27, 2012 | 1997 Chevrolet Tahoe
Oct 19, 2012 | 2000 Chevrolet Tahoe
Jul 28, 2012 | 2003 Chevrolet Tahoe
Jul 12, 2012 | 1996 Chevrolet Tahoe
Feb 04, 2011 | 2000 Chevrolet Tahoe
Feb 24, 2010 | 2000 Chevrolet Tahoe
Dec 27, 2009 | 2003 Chevrolet Tahoe
Nov 02, 2009 | 2001 Chevrolet Tahoe
146 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: