Program a keyless remote on a 2006 impala

if you have remote start dealer needs to flash it

2007 Chevy Impala Keyless Entry: Keyless Entry Only ...

www.2carpros.com/questions/2007-chevrolet-impala-chevy-keyless-entry

Dec 30, 2010 - CHEVY KEYLESS ENTRY ... 2006-2007 Chevrolet Impala, Monte Carlo ... Remove the clips holding the RCDLR antenna wire at the RCDLR module and along the "A" pillar. 5. ... Connect the new antenna to the RCDLR antenna module. 11.... The existing antenna is grounded into another wiring harness.

TPMS and key FOB range problems - LS1TECH

ls1tech.com/forums/ls4.../719926-tpms-key-fob-range-problems.html

May 24, 2007 - 2006-2007 Chevrolet Impala, Monte Carlo ... Remove the clips holding the RCDLR antenna wire at the RCDLR module and along the "A" pillar.

Buick Workshop Manuals > Lucerne V6-3.8L (2007 ...

If it is built without it then all you can do is this: http://www.bulldogsecurity.com/Products/453055507-model-ke1702-vehicle-keyless-entry-system.aspx If it is built with it then the ones you bought will not work. you will have to goto the dealer and get them programmed for the car. you cannot do it yourself

If you need further help, reach me via phone at https://www.6ya.com/expert/steven_a67ead41eb5fc62a

There is a web site for free that will tell you how to program you remotes.look up remote keyless entry replacement's

Unfortunately you may not have a choice in the matter ! You have no idea of the electronics involved here . No one knows your GM vehicle better . And $ 85 dollars is a heck of alot better then $115.00 dollars a flat rate hour . Pep boy's , firestone , AAMCO .
The keyless entry system has the following main components:
• The transmitters
• The body control module (BCM)
• The remote control door lock receiver (RCDLR)--When you press a button on the transmitter, the transmitter sends a signal to the RCDLR. The RCDLR receives the signal and sends a X Link serial data message requesting the appropriate function from the BCM.

Customer Programming Method for Enabling/Disabling the RVS Feature
Using the driver information center (DIC), the RVS feature can be DISABLED and ENABLED just like other items programmable via the DIC. When a lock control, entry-remote entry, extended range (AP8) equipped vehicle has RVS added to it and the vehicle is not DIC equipped and the customer wants to disable RVS. The dealer will perform the DISABLED remote start function since the owner cannot perform the function on thier own without a DIC.

Important: All transmitters that are to be recognized by the remote control door lock receiver (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode, all previously programmed transmitters will be erased upon receipt of the programming signal from the first transmitter.
Up to 4 transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle. The order in which the transmitters are programmed is important. The first transmitter programmed will be transmitter #1, and the second transmitter programmed will be transmitter #2. Use care to program the transmitters correctly.
The scan tool must stay connected until all of the transmitters are programmed. All doors must be closed to perform this function.
Install CANDI module.
Install a scan tool.
Turn ON the ignition with the engine OFF.
With the scan tool, select Vehicle Control Systems.
Select Computer/Integrating Systems.
Select the proper engine size.
Select Module Setup.
Select Body Control Module (BCM).
Select Program Key Fobs.
Follow scan tool on screen instructions.
Remove the scan tool.
Exit the vehicle. Attempt to lock/unlock the doors to verify the programming.
Operate the transmitter functions in order to verify correct system operation.

1. Move all Keyless Remotes out of range of vehicle. (10 to 15 feet)
2. Turn ignition key to the ON position.
3. Push the TRIP/ODO button on the DIC (Driver Info Center) twice.
4. Within 5 seconds, push & hold the FUEL INFO button on the DIC until
the PKE light comes on and stays on.
5. Turn the ignition to the OFF position, but leave the key in the ignition.
The PKE light will begin flashing.
6. Bring one Keyless Remote into range. The PKE light will stop flashing
and stay on to show the code is stored. Move the Keyless Remote out
of range. The PKE light will begin flashing indicating the system is ready
for the next Keyless Remote.
7. If more than one Keyless Remote is being programmed, move the first
Keyless Remote out of range and repeat step 6 for any additional Keyless
Remotes. Up to three Keyless Remotes can be programmed.
8. To turn off the programming mode, simply remove the key from the ignition
or turn the ignition switch on.
9. The programming mode will shut off after two minutes if.
A) You have not programmed any Keyless Remotes.
B) Removed the key from the ignition.
C) After three Keyless Remotes have been programmed.

Good luck and keep me posted.

my 2006 impala keyless remote dont work i change the battery still the same problem the spare remote same problem how to solve this problem

There is a fault code present and you will have to take it to a dealership for them to use a Tech II and read the code.

from the service manual:
There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote. Please go to the nearest GM dealer for assistance

Check your owners manual. You might be able to do it through the controls on the radio.