- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
You could have a bad tpms sensor in one of the tires here's how to check it
Step 2:
Reading TPMS codes and clearing them There is a simple procedure to perform a self diagnostic and clear the codes.
1) Turn IGN switch to ON. 2)
Locate the TPMS warning check connector. It is a single loose wire
with a connector located under the dash next to the steering column.
It may be bundled with the OBDII diagnostic connector. 3) Using a
suitable piece of bare wire inserted into the connector (a paperclip
will do), momentarily ground the wire to the chassis.
NOTE: If you are uncomfortable doing this, then don't. You could damage your vehicle if the wrong wire is grounded.
Step 3:
4) The TPMS low tire pressure warning light will blink error codes as follows:
5sec. ON - 5sec. OFF Long (1 sec) blink = First digit (2 blinks = 2) Short (0.2 sec) blink = Second digit (ie 3 short blinks = 3)
There is a 2 second pause between multiple codes.The cycle will keep repeating starting with 5sec. ON
Codes:
15 - Front LH tire pressure drops to 26 psi or less. 16 - Front RH tire pressure drops to 26 psi or less. 17 - Rear RH tire pressure drops to 26 psi or less. 18 - Rear LH tire pressure drops to 26 psi or less. 21 - Data from front LH transmitter can not be receive. 22 - Data from front RH transmitter can not be receive. 23 - Data from Rear RH transmitter can not be receive. 24 - Data from Rear LH transmitter can not be receive. 31 - Checksum data from front LH transmitter is malfunctioning. 32 - Checksum data from front RH transmitter is malfunctioning. 33 - Checksum data from rear RH transmitter is malfunctioning. 34 - Checksum data from rear RH transmitter is malfunctioning.
Use the listing on the door jamb, not the side of the tire. If all are ok, then one of the sensors may have been damaged when replacing the tires? Be sure the spare is OK. some spares will have a sensor.
It is possible that one of the sensors was damaged when they replaced the tires. If this occurred, the light will remain lit. Otherwise, after a pressure change the light will automatically turnoff after driving several minutes above 25MPH.
There is also a Nissan TPM reset tool which is designed to turn off the TPM warning light in 2003 and newer Nissan vehicles that have the TPM reset connector. Check your owner's manual to see if your vehicle has the connector. You can find the reset tool online for about $25.
it mean that your tire pressure is low or tire pressure sensor is malfunctioning ,set tire pressure at 35 psi and drive for 1/4 mile to see if the ligth goes off
Just put the proper amount of air into the tire, it is usually is 32 psi and it might take 20 to 30 miles before it registers that the right amount of air is in the tire
First make sure all of the tires have at least 35 psi in them. The warning light comes on at 27.5 psi and goes off at above 33.5 psi. So make sure that you have the required 35 psi first. Once you have that, drive the vehicle a short distance the light should go out. If the light does not go out you can take it to the dealer to have them re-activate your sensors. Most tire shop have this tool also.
The tire pressures to use are i your user manual that came in the glovebox. If you no longer have this, buy a 20 dollar manual, which I buy for every car I own and it wil tell you.
If you need an answer to get you by, use 35 psi until you find out exactly what it should be. You may even want to stay with this pressure, as most car manuals wil give you temps for winter and summer, and for different driving conditions, when 35 psi will serve you just fine. If you begin to notice your tir wear is not even, take it to a shop and find out what is wrong with it. You will probably need an alignment.
Also many tires wil tell you on the side, the safe tire inflation pressures, but I have found that 35 psi is a good number to run for just about any passenger car.
You need to set all the pressures to 35 psi. first then drive for approx.1/4 mile. If this doesn't work to reset the light (keep in mind the code itself will still be stored even though the light goes off) you will need to take it to your Nissan Dealer to have it scanned as there may be a malfunction with the sensor. If faulty and you are under 36k miles then it should be covered under your factory warranty. Hope this helps.
Look for a sticker on the drivers door panel. It will tell you what pressure to set for the tires. The owners manual may also contain this information. It is normal for a radial tire to look a little flat.
make sure all your tire pressures are above 35psi. the light will come on if your tires are below 28 psi. check all your tires for tire pressure. if pressures are low, add air and drive truck at 35+mph for about 1 mile and the light will go out unless you have a sensor problem, but fotha the light will be flashing. so to sum it up, check your tirpressures and make sure, that you have 35 psi in all 4 tires.
×