2004 galant 2.4 exhaust manifold bolt torque spec

Intake Manifold Torque specs? - Maxima Forums

https://maxima.org > 4th-generation-maxima-1995-1999
Jan 25, 2017 - What do you torque the intake manifold to? ... My haynes manual says to torque the upper manifold bolts to 13-16 ft/lbs ... Supporting Maxima.org Member.
valve cover and intake plenum bolt torque specs - Maxima ...
Mar 19, 2020
Valve Cover Torque Spec. - Maxima Forums
Oct 31, 2004
2000 upper intake manifold collector removal - Maxima Forums
Jan 25, 2017
01 Maxima - harmonic balancer bolt torque spec please
Aug 9, 2015
More results from maxima.org

VIDEOS as well

https://www.google.com/search?q=Intake+manifold+torque+specs+for+2013+maxima

..

Intake torque specs ' FordForumsOnline.com

www.fordforumsonline.com > Ford Tech Forums > Engine & Drivetrain

May 7, 2010 - 2 posts - ‎2 authors
ISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).

Torque Specifications - AutoZone

www.autozone.com/.../Ford-Windstar.../Specifications/Torque-...

AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Exhaust Manifold To Cylinder Head - 9.58 ft lbs
Exhaust Pipe To Exhaust Manifold - 20 ft lbs
you can check it out here, also all other torque specs for your engine.
Torque Specs Database

Install the cylinder head bolts. Starting at top center, tighten all cylinder head bolts in sequence as shown in illustration, using the Cylinder Head Bolt Wrench (09221 - 32001) or equivalent. Repeat the procedure, re-tightening all cylinder head bolt to the specified torque. (torque spec is Cold Engine 105-115 Nm (76-83 ft lb) )
. Install the timing belt tensioner pulley.
. Install the timing belt on the camshaft sprocket, making sure that the tension side is tightened by turning the camshaft sprocket in reverse, all timing marks are in alignment.
. Adjust the timing according to "Timing Belt"
. Install the rocker cover and tighten the bolts to the specified torque. Tightening torque: Rocker cover belt:

2.5-3.5 Nm (25-35 kg.cm, 2-3 ft. lbs.)

. Install the timing belt cover.
Install the new intake manifold gasket and the intake manifold. Tighten the nuts and bolts to the specified torque.
Install the new exhaust manifold gasket and the exhaust manifold. Tighten the exhaust manifold attaching nuts to the specified torque.
. Install the surge tank and tighten the nuts bolts to the specified torque.
. Install the power steering oil pump and bracket.
. Install the ignition coil.
. Install the air intake hose.
Connect the vacuum hose, fuel hose and water hose.
. Install breather hose.

Fig. Left side exhaust manifold bolt torque sequence-3.0L engine




Fig. Right side exhaust manifold bolt torque sequence-3.0L engine

Both cases, exhaust manifold and new gasket, torque the bolts to 15 ft. lbs. (20 Nm).

Good luck (remember to rate this answer).

Exhaust manifold bolts-first pass 11 Lb/Ft. Exhaust manifold bolts-final pass 18 Lb/Ft. Exhaust manifold heat shield bolts 7 Lb/Ft. Note: To torque bolts & nuts, start in center using crisscross pattern working outward

Cylinder Head Bolt Step1- (25 FT.Lbs) Step2(45 Ft.Lbs) Step3(65Ft,Lbs).....Intake Manifold(35Ft Lbs)....Exhaust Manifold Center (20Ft Lbs) All Others (20 Ftlbs).....Thanks