Question about 2007 Nissan Xterra Off Road

Open Question

Instrument panel removing on 2006 xtrail - 2007 Nissan Xterra Off Road

Posted by Anonymous on

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2006 Pontiac grand prix where is the blend door actuator mode at




  1. Remove the right instrument panel (I/P) insulator. Refer to Instrument Panel Insulator Panel Replacement - Right Side in Instrument Panel, Gages, and Console.


  2. Remove the I/P compartment. Refer to Instrument Panel Compartment Replacement in Instrument Panel, Gages, and Console.

    alt="Object Number: 1194925 Size: SH">



  3. alt="Click here for detailed picture of above image.">


  4. Remove the screws that secure the mode actuator (1) to the HVAC module assembly.


  5. Remove the mode actuator from the HVAC module assembly.


  6. Disconnect the electrical connector from the mode actuator.



a+2saweek5chaaaaaelftksuqmcc



Instrument Panel Insulator Panel Replacement - Right Side



Remove 3 fasteners. Rotate the lamp. Remove the lamp from the insulator. Remove the insulator.



Instrument Panel Compartment Replacement



Using the finger opening, remove the access hole cover from the right instrument panel (I/P) compartment



Pull the I/P outboard trim plate rearward in order to release the retainers. Remove the I/P trim plate. Open the I/P compartment



Disengage the compartment door stop using the following procedure:







5.1.





Press the upper door stop (2) toward the center of the vehicle.














5.2.





Rotate the door away from the compartment.








Pull the I/P accessory trim plate rearward slightly for access to the I/P inboard trim plate. Refer to Instrument Panel Accessory Trim Plate Replacement .

alt="Object Number: 929399 Size: SH">

Jan 12, 2016 | Pontiac Cars & Trucks

1 Answer

How to change head light assy on nissan xtrail 2006 model


you have to remove the front bumper. there is a hidden bolt on the lower assembly.
it is to prevent theft

Feb 23, 2015 | Nissan Cars & Trucks

1 Answer

Nissan xtrail QR20 ENGINE oil pump not working


2006 xtrail was overfilled with oil now oil light is coming on and am getting a noise from engine. Help

Jun 07, 2013 | Cars & Trucks

1 Answer

Remove gear she knob xtrail


It just pulls of with a great amount of upward force.

Oct 30, 2012 | 2006 Nissan Altima

2 Answers

Who knows where I can get a guide to replace the Heater Core on my 2006 Ford Freestar?


I have the shop manual & wiring book from Ford for your car. If interested, let me know. $25 plus postage.

this is a big job, time consuming. Is it leaking coolant?

Removal and Installation
NOTE: If a heater core leak is suspected, the heater core must be leak tested before it is removed from the vehicle.
  1. Drain the cooling system. For additional information, refer to Section 303-03.
  1. Position the front seats fully rearward.
  1. Depower the supplemental restraint system. For additional information, refer to Section 501-20B.
  1. Remove the wiper motor and pivot assembly. For additional information, refer to Section 501-16.
  1. Remove the LH and RH windshield side garnish mouldings. For additional information, refer to Section 501-05.
  1. Remove the LH and RH A-pillar lower trim panels. For additional information, refer to Section 501-05.
  1. Disconnect the heater hoses from the heater core.
  1. Lower the glove compartment.
  1. Remove the 3 steering column opening panel lower bolts.
    • To install, tighten to 8 Nm (71 lb-in).
  1. Remove the steering column opening panel cover.
  1. Remove the steering column opening panel upper bolts.
    • To install, tighten to 8 Nm (71 lb-in).
  1. Remove the steering column opening panel reinforcement.
  1. Remove the 4 storage console pin-type retainers.
  1. Remove the storage console.
  1. Remove the rear seat floor duct adapter.
  1. Remove the upper instrument panel finish panel.
  1. Remove the LH lower instrument panel bolt.
    • To install, tighten to 12 Nm (9 lb-ft).
  1. Remove the LH upper instrument panel bolt.
    • To install, tighten to 12 Nm (9 lb-ft).
  1. Remove the 4 upper instrument panel bolts.
  1. Remove the upper instrument panel cowl bolt.
    • To install, tighten to 5 Nm (44 lb-in).
  1. Remove the 4 instrument panel center support brace bolts.
    • To install, tighten to 12 Nm (9 lb-ft).
  1. Remove the LH instrument panel support bracket bolt.
    • To install, tighten to 12 Nm (9 lb-ft).
  1. Loosen the RH instrument panel bolts one half of the bolt length, but do not completely remove the bolts.
    • To install, tighten to 12 Nm (9 lb-ft).
  1. Working through the glove compartment opening, remove the RH instrument panel support bracket bolt.
    a0083958.jpg
  1. Position the LH side of the instrument panel slightly away from the dash panel.
  1. Remove the heater core and evaporator core housing support brace nut.
  1. Remove the heater core and evaporator core housing support brace bolt.
  1. Remove the heater core and evaporator core housing support brace.
  1. Remove the 4 floor duct screws.
  1. Remove the floor duct.
  1. Remove the 7 heater core cover screws.
  1. Detach the wire harness from the heater core cover.
  1. Remove the heater core cover.
  1. Remove the heater core.
  1. To install, reverse the removal procedure.
  1. Fill the engine cooling system. For additional information, refer to Section 303-03.

Oct 31, 2011 | 2006 Ford Freestar

1 Answer

Remove dash in 2006 f150


INSTRUMENT PANEL

Removal and Installation
  1. If equipped with adjustable pedals, move the pedals to the full forward position.
  2. If equipped with a floor console, remove the floor console.
  3. WARNING: To reduce the risk of serious personal injury, read and follow all warnings, cautions, notes and instructions in the supplemental restraint system (SRS) deactivation/reactivation procedure.
Depower the supplemental restraint system (SRS).

  1. Position the LH and RH door weatherstrip seals aside.
  2. Remove the A-pillar trim panels and RH cowl side trim panel.
  3. Remove the LH and RH instrument panel side finish panels.
  4. Remove the 2 steering column opening trim screws.
  5. Remove the steering column opening trim.
  6. Remove the steering column cover.
  7. Remove the instrument cluster finish panel.
  8. Remove the instrument panel center finish panel.
  9. Remove the instrument cluster center finish panel.
  10. Remove the parking brake release handle bolt.
    • To install, tighten to 9 Nm (80 lb-in) .
  1. Position aside the parking brake release handle.
    • Remove the parking brake release handle pin-type retainer.
  1. Remove the hood release handle bolt.
    • To install, tighten to 9 Nm (80 lb-in) .
  1. Position aside the hood release handle.
  2. Loosen the electrical connector screw and disconnect the bulkhead electrical connector.
  3. Remove the ground bolt.
    • To install, tighten to 12 Nm (9 lb-ft) .
  1. Disconnect the electrical connectors.
  2. Position aside the front carpet.
  3. Remove the 4 LH center brace bolts.
    • To install, tighten to 9 Nm (80 lb-in) .
  1. Remove the LH center brace.
  2. If equipped, disconnect the transmission range indicator cable and position aside.
  3. CAUTION: To avoid damage to the clockspring, do not allow the steering column shaft to rotate while the intermediate shaft is disconnected.
Remove the steering column pinch bolt and disconnect the steering column intermediate shaft.
  • To install, tighten to 40 Nm (30 lb-ft) .
  1. Disconnect the steering column electrical connector.
  2. Remove the ground bolt.
    • To install, tighten to 12 Nm (9 lb-ft) .
  1. Disconnect the radio antenna.
  2. Disconnect the 4 PDB (B1, B2, L1 and L2) electrical connectors.
  3. Disconnect the ETAC electrical connector.
  4. Disconnect the instrument panel electrical connectors.
  5. Position aside the front carpet.
  6. Remove the 4 RH center brace bolts.
    • To install, tighten to 9 Nm (80 lb-in) .
  1. Remove the RH center brace.

  1. NOTE: If equipped with a floor console, remove the third center brace.
If equipped, remove the 4 third center brace bolts.
  • To install, tighten to 9 Nm (80 lb-in) .
  1. If equipped, remove the third center brace.
  2. Remove the 2 defrost grilles.

  1. Disconnect the wiring harness pin-type retainer.
  2. CAUTION: To avoid damage to the instrument panel, an assistant is required to support the panel before carrying out this step.
Remove the 9 instrument panel bolts.
  • To install, tighten to 20 Nm (15 lb-ft) .
  1. CAUTION: Before removing the instrument panel, make sure all electrical connector wiring is free and not hindered.
Remove the instrument panel.

  1. To install, reverse the removal procedure.

Oct 20, 2010 | 2006 Ford F-150

1 Answer

2006 hhr to take out ignition switch out


Removal & Installation

1. Disable the SIR system.


28d6a49.gif
Remove the Instrument Panel (I/P) center trim panel by releasing the retaining fasteners

  1. Remove the Instrument Panel (I/P) center trim panel (1) by pulling out on the trim panel in order to release the retaining fasteners (2).
  2. Disconnect the electrical connectors on the Instrument Panel (I/P) center trim panel (1).

dc7f057.gif
Remove the steering column opening filler assembly, with clip, & bumper

3. Remove the steering column opening filler assembly (1) by pulling away the clips (2).
4. Disconnect the electrical connector for the trunk release.


77e0f1d.gif

Remove the Instrument Panel (I/P) left side trim panel

  1. Remove the Instrument Panel (I/P) left side trim panel (1).
  2. Tilt the steering wheel up.
  3. Disconnect the I/P dimmer switch and, if equipped, the fog lamp switch.

88e8dec.gif

Remove the 4 bezel screws (2) & the Instrument Panel (I/P) cluster bezel assembly (1)

  1. Tilt the steering wheel down.
  2. Remove the 4 instrument panel cluster bezel screws.
  3. Remove the instrument panel cluster bezel.

810fe4a.gif

Remove the steering column trim covers: steering column upper cover assembly, steering column left cover assembly, & steering column right cover assembly

Remove the steering column trim covers:
  • Remove the 3 cover screws (4).
  • Remove the steering column upper cover assembly (1).
  • Remove the steering column left cover assembly (2).
  • Remove the steering column right cover assembly (3).


bd6042a.gif
Removal of the ignition switch

    1. Disconnect the ignition switch harness connector.
    1. WARNING
    The ignition switch must be in the run position during removal in order to avoid damage to the ignition switch.

    1. Turn the ignition switch to the run position.
    2. Remove the ignition switch screws.
    3. Remove the ignition switch from the steering column.
    To install:
    1. Install the ignition switch and screws on to the steering column. Tighten the screws to 17 inch lbs. (2 Nm).
    2. Connect the ignition switch harness connector.
    3. Installation is the reverse of removal procedure.
    4. Tighten the trim cover screws to 17 inch lbs. (2 Nm)
    5. Tighten the 4 instrument panel cluster bezel screws to 19 inch lbs. (2 Nm)
    6. Enable the SIR system. Refer to Air Bag (Supplemental Restraint System), arming the system.
      NOTE If the ignition switch is replaced and a learn procedure is not performed, the engine will crank but not start or will start and stall immediately.

    7. Perform the vehicle theft deterrent system learn procedure.

    Mar 12, 2010 | 2006 Chevrolet HHR

    1 Answer

    How do i remove the stereo on my 2006 f250 pu


    Removal and Installation
    1. Tilt the steering wheel downward.
    1. NOTE: Ignition switch must be in OFF position if disconnecting the passenger airbag deactivation (PAD) switch electrical connector. Otherwise, a diagnostic trouble code (DTC) will be set in the restraints control module (RCM) memory and must be erased before releasing the vehicle.
      Position the ignition switch in the OFF position.
    1. Remove the instrument panel cluster finish panel.
      • Pull outward on the instrument panel center finish panel, as indicated, to release the retaining clips.
      • Disconnect the electrical connectors.
      n0080164.gif
    1. To install, reverse the removal procedure.
    Audio Unit n0029180.gif
    Item Part Number Description 1 — Audio unit screws (4 required) 2 18C869 Audio unit 3 — Audio unit electrical connector (part of 14401)
    Removal and Installation
    1. Remove the instrument cluster finish panel. For additional information, refer to.
    1. Remove the 4 screws and the audio unit.
      • Disconnect the electrical connector and the antenna lead-in cable.
    1. To install, reverse the removal procedure.

    Jun 04, 2009 | 2006 Ford F-250 Super Duty

    Not finding what you are looking for?
    2007 Nissan Xterra Off Road Logo

    Related Topics:

    51 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Nissan Experts

    Marvin
    Marvin

    Level 3 Expert

    85239 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    14852 Answers

    Vincent G
    Vincent G

    Level 3 Expert

    2363 Answers

    Are you a Nissan Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...