Question about 2000 Ford Expedition

1 Answer

Abs light on a 06 expedition

XLT, Expedition 2006 ABS light came on and the ABS stops working. also noticed that the AWD doesn't engage when slipping. 4x4 H works fine. in AWD the 4x4 light comes on when ii press breaks. ABS is off when i start it but comes on after first braking. Any Ideas? I looked for a speed sensor in the rear end diff but could not locate?

Posted by Anonymous on

Ad

1 Answer

Jeff Armer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 15,575 Answers

Having the vehicle checked for DTC'S - diagnostic trouble code's would be a good first step . ABS light on codes are stored . Suggest you take your vehicle to a qualified repair shop that has the knowledge an testing equipment to diagnose the problem properly .
Anti-Lock Brake System (ABS)
The 4-wheel, 4-channel anti-lock brake system (ABS) consists of the following components:

  • ABS module
  • Front wheel speed sensor
  • Front wheel speed sensor ring (integral to the front wheel bearing)
  • Hydraulic control unit (HCU)
  • Rear wheel speed sensor
  • Rear wheel speed sensor ring (integral to the rear halfshaft)
  • Yellow ABS warning indicator
  • As you can see here , it can set numerous
  • DTC'S Why guess an replace parts that won't fix the problem .
  • Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1342 ECU is Faulted ABS Module NOTE: If other DTCs are present, REPAIR them before installing a new component.
    CLEAR the DTCs. RETRIEVE the DTCs. If DTC B1342 is retrieved, INSTALL a new module. REFER to Anti-Lock Brake System (ABS) Module in this section. REPEAT the self-test. B1483 Brake Pedal Input Circuit Failure ABS Module Go To Pinpoint Test B . B1676 Battery Pack Voltage Out of Range ABS Module Go To Pinpoint Test C . B2477 Module Configuration Failure ABS Module CONFIGURE the ABS module. REFER to Section 418-01 . CLEAR the DTCs. REPEAT the self-test. If DTC B2477 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . REPEAT the self-test. B2734 Pedal Travel Sensor Supply Error ABS Module Go To Pinpoint Test M . B2736 Pedal Travel Sensor Circuit Fault ABS Module Go To Pinpoint Test M . B2737 Pedal Travel Sensor Jammed Error ABS Module Go To Pinpoint Test M . B2738 Pedal Travel Sensor Velocity Error ABS Module Go To Pinpoint Test M . B2740 Pedal Travel Sensor Spike Error ABS Module Go To Pinpoint Test M . B2741 Sensor Cluster Defective ABS Module FOLLOW the diagnostic tool directions for the calibration procedure. B2900 VIN Mismatch ABS Module VERIFY that the module has the correct as-built data.
    CHECK for correct powertrain control module (PCM) and ABS module configurations using the diagnostic tool. RECONFIGURE the component as necessary. FOLLOW the diagnostic tool directions for the ABS module configuration or REFER to Section 418-01 for the PCM. CLEAR the DTC. REPEAT the self-test. C1095 ABS Hydraulic Pump Motor Circuit Failure ABS Module Go To Pinpoint Test D . C1145 Speed Wheel Sensor RF Input Circuit Failure ABS Module Go To Pinpoint Test E . C1155 Speed Wheel Sensor LF Input Circuit Failure ABS Module Go To Pinpoint Test E . C1165 Speed Wheel Sensor RR Input Circuit Failure ABS Module Go To Pinpoint Test E . C1175 Speed Wheel Sensor LR Input Circuit Failure ABS Module Go To Pinpoint Test E . C1233 Speed Wheel LF Input Signal Missing ABS Module Go To Pinpoint Test F . C1234 Speed Wheel RF Input Signal Missing ABS Module Go To Pinpoint Test F . C1235 Speed Wheel RR Input Signal Missing ABS Module Go To Pinpoint Test F . C1236 Speed Wheel LR Input Signal Missing ABS Module Go To Pinpoint Test F . C1277 Steering Wheel Angle 1 and 2 Circuit Failure ABS Module Go To Pinpoint Test G . C1278 Steering Wheel Angle 1 and 2 Signal Faulted ABS Module Go To Pinpoint Test G . C1279 Yaw Rate Sensor Circuit Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C1280 Yaw Rate Sensor Signal Fault (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C1281 Lateral Accelerometer Circuit Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C1282 Lateral Accelerometer Signal Fault (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C1285 Booster Solenoid Circuit Failure ABS Module Go To Pinpoint Test I . C1287 Booster Pedal Force Switch Circuit Failure ABS Module Go To Pinpoint Test J . C1288 Pressure Sensor Main/Primary Input Circuit Failure ABS Module Go To Pinpoint Test K . C1440 (with stability assist) Pressure Sensor Main/Primary Signal Faulted ABS Module Go To Pinpoint Test K . C1516 Roll Rate Sensor Signal Fault (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C1517 Roll Rate Sensor Circuit Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C1730 Reference Voltage Out of Range (+5V) ABS Module Go To Pinpoint Test L . C1805 Mismatched PCM and/or ABS-TC Module ABS Module CHECK for correct PCM and ABS module configuration using the diagnostic tool. RECONFIGURE the component as necessary. FOLLOW the diagnostic tool directions for the ABS module configuration or REFER to Section 303-01 for the PCM. CLEAR the DTC. REPEAT the self-test. C1963 Stability Control Inhibit Warning ABS Module This DTC is for information only. GO to the Principles of Operation. CLEAR the DTC. REPEAT the self-test. C1991 Module Calibration Failure ABS Module Follow the diagnostic tool directions for the calibration procedure. C1996 Active Yaw and/or Roll Control Disabled ABS Module This DTC can be set if the ABS module system is activated for 15 seconds of continuous operation. CHECK for any major chassis modifications, gross suspension misalignment or other items that can alter the vehicle tracking dynamics. CLEAR the DTC. REPEAT the self-test. C1998 Module Calibration Not Complete ABS Module Go To Pinpoint Test O . C2769 (ABS only) Longitudinal Acceleration Sensor Electrical Failure ABS Module INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. CLEAR the DTCs. REPEAT the self-test. C2769 (ABS with stability assist) Longitudinal Acceleration Sensor Electrical Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C2770 (ABS only) Longitudinal Acceleration Sensor Plausibility Failure ABS Module INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. CLEAR the DTCs. REPEAT the self-test. C2770 (ABS with stability assist) Longitudinal Acceleration Sensor Plausibility Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C2777 Sensor Cluster Bus Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C2778 Sensor Cluster Power Supply Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . U1900 CAN Communication Bus Fault-Receive Error Network Fault REFER to Section 418-00 . U1901 CAN Network #2 Communication Bus Fault-Receive Error Network Fault Go To Pinpoint Test H . U2023 Fault Received from External Node Instrument Cluster REFER to Section 418-00 .

Posted on Oct 24, 2017

Ad

5 Related Answers

Anonymous

  • 1010 Answers

SOURCE: abs light on

I'm a Ford service adviser. There are many reasons for the
abs warning indicator to come on. The usual cause is from a
faulty speed sensor. Either a wheel speed sensor or the
differential speed sensor. I don't think the light is related to your vandalism. You might want to take the truck to an auto parts store and have them read the codes for you. Most auto parts stores will do this for free.
Good Luck

Posted on Jun 23, 2008

Ad

Anonymous

  • 2 Answers

SOURCE: remote starter

I had the same issue with my remote start on another vehicle, the part that bypasses the code on the key had to be reset. The way we figured it out was everything was normal except the vehicle did not start & the security light flashed rapidly.

Posted on Jan 18, 2009

moparownr

Jeff Hammack

  • 667 Answers

SOURCE: 2004 Ford Expedition XLT, front blend door actuator

Hope I was avle to help, glad you up and going.

Posted on May 27, 2009

Anonymous

  • 66 Answers

SOURCE: 99 ford expedition, abs light stays on, front

When was the last time you changed the front brake pads?
Try this:
Keep the brake pedal pressed down and start the car, after it idles for about 10 second let go of the pedal. If the light comes on just as you leave the pedal - try pumping it a few times, turn the car off and pump the pedal some more until it becomes real hard.
Then, keeping your foot to the pedal, start the car.
Idle for about 10 seconds, let go of the pedal and press it again rel fast.
If the light doesnt come on again - it means you have a leak of some sort or that the main brake pump should be replaced.

Good luck.

Posted on Jul 11, 2009

brent williams

  • 1 Answer

SOURCE: 97 expedition - 4x4 does not engage

the first thing i would check on any 4x4 AWD is to see if the vacume lines
were conected to the transfor case and getting vacume when engaded i have found this to be the
most commen answer

Posted on Jun 15, 2012

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Jeep comanche 4x4


check the condition of the vacuum hose as it may have cracks in it or it is loose on the actuator.

Dec 21, 2013 | Jeep Cars & Trucks

1 Answer

2006 Mountaineer 4x4 light on awd stuck.


Have a shop diagnose the problem if you
have not purchased the factory diagnostic
manuals from Helm.Com
Don't know why you would think fluid change on
any part of the vehicle would do a thing
Have you not checked for codes
That is always the first thing you do even
without a MIL lamp on.

Jul 23, 2013 | Mercury Mountaineer Cars & Trucks

1 Answer

How do I check the vacuum system for 4x4 on F150 2006


Engage the 4x4 and using a vacuum gage check for approx. 14-15" of vacuum at the lines to the actuators.

Nov 01, 2017 | 2006 Ford F-150

1 Answer

I have a 1998 Ford Expedition and I can't get the 4 X 4 high to engage.The other day I got caught in the snow and I couldn't get the truck to go into 4 X 4 high or AWD however it would go into 4 X 4 low....


The 4x4 systems on those are mostly electical. I've had many fords have problems with the 4x4 electic motor mounted on the transfer case. In most cases if you tap on the transfer case motor when trying to engage 4x4 it will start to work. This is most likely if 4x4 is seldom used.

Jan 11, 2011 | 1998 Ford Expedition

3 Answers

97 expedition - 4x4 does not engage


i have the same problem can't figured it out although when i turn the knob to AWD the light on dash just flashes. the 4x4 H and 4x4 L light on dash stays on.if u have found out anything please let me know or e mail me at [email protected] Thanks Don

Jan 28, 2010 | 1997 Ford Expedition

4 Answers

How do you know when your in A4WD?


no you have it reversed....if the light is on its in awd if its off its not

Feb 14, 2009 | 2006 Ford Expedition

1 Answer

Flashing 4x4 light


4 wheel drive controler is going out? have the tranfercase oil change some times the oil gets burned and the gears do not slip the senser picks this up

Jan 08, 2009 | 1999 Ford Expedition

3 Answers

Nissan 2006 navara 4x4 does not engage and AB warning light stea


check your ABS sensors.... sometimes they can get dirty and not read the wheel right.... that might fix you ABS solution.... and possibly your 4x4 it doesnt want to engage in 4 wheel cause of the abs

Jan 02, 2009 | 2007 Nissan Frontier SE Crew Cab

1 Answer

'98 Ford Expedition - 4WD/AWD won't engage. The switch to engage the 4WD/AWD does not light up and the 4WD/AWD will not engage. No engaging noises or anything. It's as if the switch has...


I had a similar problem, but not exactly the same. In my expedition 98 the A4WD worked, but the 4x4 hi or low did not. Ford dealership diagnosed it to be the transfer case shift motor. I bought one from ebay for $85 and replaced it myself and it works fine now. They wanted $450 to replace it.

Some say you can tap the transfer case motor with hammer, but gently and it may come to life. I didn't try that.

Dec 21, 2008 | 1998 Ford Expedition

Not finding what you are looking for?
2000 Ford Expedition Logo

Related Topics:

1,295 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...