Fuse chart what fuse is it that is used for my windshield wipers i dont have the fuse chart

The is the symptom of a defective wiper switch.

Probably the electronic board is bad that controls the delay.

1997 mercury wagon ? Sable ? VISUAL INSPECTION CHART-WINDSHIELD WIPER AND WASHER SYSTEMS Mechanical Electrical

• Windshield wiper blade missing or damaged.
• Binding windshield wiper pivot arm.
• Binding windshield wiper mounting arm and pivot shaft.
• Empty windshield washer reservoir.
• Kinked or broken windshield washer hoses.

• Open fuse junction panel Fuses:
  • 8 (5A)
  • 12 (5A)
  • 20 (5A)
  • 23 (5A)
• Damaged windshield wiper motor.
• Damaged windshield washer pump.
• Open connectors.
• Corroded connectors.
• Inoperative multi-function switch.
• Open thermal breaker internal to the wiper motor

Which are not working , front , back or all ?

I/P Fuse Panel C225
Under left corner of instrument cluster

the wiper fuses / relays are in the top left of the fusebox

Have you done a Probe Test on the vehicle? A Probe Light Tester can help you locate a short in your cars electrical system. To learn what a Probe Tester is and How to use it, watch the following video: https://www.youtube.com/watch?v=tXzKcEyIOq8

This is a complex wiper system . Here are all the components involved !
The Wiper/Washer System consists of the following components:
?€¢
Windshield wiper/washer switch

?€¢
Body control module (BCM)

?€¢
Wiper 1 relay

?€¢
Wiper 2 relay

?€¢
Wiper diode

?€¢
Windshield wiper motor

?€¢
Windshield washer pump

?€¢
Windshield washer nozzles

?€¢
Windshield washer solvent container

?€¢
Windshield wiper arm and blade assemblies

?€¢
Windshield wiper transmission

?€¢
WIPER/SW 10A fuse

?€¢
WIPER 25A fuse

Circuit/System Description
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation. The windshield wiper motor park operation is controlled by the BCM. The BCM recieves an input from the park switch to determine wiper blade position. When the wiper blades are at the bottom of the windshield glass in park position the wiper park switch will open and the circuit will be pulled up to B+ by the BCM. The park signal will be pulled to ground by the wiper motor park switch while the wiper blades are not in the park position.
The BCM controls the windshield wiper motor through two output controls, controlling two relays which determine the desired wiper speed, high or low
Diagnostic Trouble Codes (DTCs)
The body control module (BCM) monitors the voltage on the windshield wiper switch signal 2 circuit for diagnostic purposes. If the circuit is shorted to voltage while the driver is commanded OFF, the BCM will store DTC B3715. If the circuit is shorted to ground while the driver is commanded ON, the BCM will store DTC B3715. Refer to DTC B3715.
It would be best to have a factory scan tool to diagnose this problem . it would make it easier anyway .
It

drivers side inner fender under the hood, look in the owners manual for the number and amps. some are marked under the lid itself

If you need further help, I’m available over the phone at https://www.6ya.com/expert/david_4c166ba81493f541

The windshield wiper motor is a smart wiper motor with an integrated electronics module. The internal components of the motor are the high/low relay, washer pump relay, and the run/park relay and associated electronics.
The windshield wiper motor receives its inputs from the windshield wiper/washer switch. These signals are ground reference signals. When the switch is placed in different positions, various input signals are selected and sent through circuits to the motor. The windshield wiper motor module identifies these selected input signals and activates the motor to the selected function.!
Your probably going to need a new wiper motor ! ! ! But you should always test before replacing parts !
Visual Inspection Chart Mechanical Electrical

• Windshield washer pump hoses
• Windshield wiper mounting arm and pivot shaft

• Bussed electrical center (BEC) fuse 10 (30A)
• Smart junction box (SJB) fuse 3 (10A)
• Circuitry
• Windshield wiper motor
• Windshield washer pump
• Windshield wiper/washer switch

• The wipers stay on continuously

• Circuitry
• Windshield wiper motor
• Windshield wiper/washer switch

• Go To Pinpoint Test C .

PINPOINT TEST C: THE WIPERS STAY ON CONTINUOUSLY CAUTION: Use the correct probe adaptor(s) when making measurements. Failure to use the correct probe adaptor(s) may damage the connector.
Test Step Result / Action to Take C1 CHECK THE WINDSHIELD WIPER/WASHER SWITCH

• Key in OFF position.
• Disconnect: Windshield Wiper/Washer Switch C2137.
• Carry out the windshield wiper/washer switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  
• Does the windshield wiper/washer switch pass the component test?

Yes
GO to C2 .

No
INSTALL a new windshield wiper/washer switch. REFER to Wiper/Washer Switch in this section. C2 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR A SHORT TO GROUND

• Disconnect: Windshield Wiper Motor C125.
• Measure the resistance between the windshield wiper motor C125, harness side and ground as follows:
  
  Windshield Wiper Motor C125 Pin Circuit C125-10 56 (DB/OG) C125-11 58 (WH) C125-1 63 (RD) C125-9 61 (YE/RD)
  
  
• Are the resistances greater than 10,000 ohms?

Yes
GO to C3 .

No
REPAIR the circuit(s). TEST the system for normal operation. C3 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION

• Disconnect all the windshield wiper motor connectors.
• Check for:
  • corrosion.
  • pushed-out pins.
• Connect all the windshield wiper motor connectors and make sure they seat correctly.
• Operate the system and verify the concern is still present.
• Is the concern still present?

Yes
INSTALL a new windshield wiper motor. REFER to Wiper Motor in this section. TEST the system for normal operation.

No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
You

fuse panel in car on driver side by left knee under dash


Visual Inspection Chart
Mechanical Electrical

• Wiper linkage
• Washer nozzles
• Washer pump hoses

• Central junction box (CJB) Fuse 211 (15A), Fuse 215 (30A)
• Multifunction switch
• Rear window wiper switch
• Wiper run/park relay
• Wiper high/low relay
• Windshield wiper motor
• Windshield washer pump
• Rear window washer pump
• Circuitry
• Battery junction box (BJB)
• CJB
• Generic electronic module (GEM)

10 amp in interior fuse panel. And a main 30 Amp fuse feed in interior panel. see chart in owner guide or on fuse panel cover.