Dented drivers front door and quarter panel

they re both 3rd generation so body lines match ----- and switching out a rear quarter entails welding and fabing the metal and if damage extends to the wheel well will need to do the same - then finish and blending paint

need to do body work but if the pillar is bent in will need a frame straightener to pull out best is to have a body shop do the work

Remove the door opening weather-strip. Refer to Door Opening Weatherstrip Replacement in Doors.
Remove side sill trim plate. Refer to Door Sill Plate Replacement in Interior Trim.
Remove the lower quarter panel trim. Refer to Rear Quarter Trim Panel Replacement in Interior Trim.
Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement in Interior Trim.
Remove the quarter upper trim panel. Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.
Remove the center pillar outer applique. Refer to Center Pillar Applique Replacement in Exterior Trim.
Remove the roof drip molding. Refer to Body Side Roof Drip Molding Replacement in Exterior Trim.

Important: It is necessary to use new nuts when reinstalling the quarter window.
Remove the nine quarter window nuts (1), securing the quarter window assembly (2) to the body opening.
Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.
Important: When removing the quarter window from the body opening make sure that the attaching pins are clear of the outer body.
Remove the quarter window (2) from the body opening.

Remove the rear seat cushion. Refer to Rear Seat Cushion Replacement in Seats.
Remove the rear seat back. Refer to Rear Seat Back Replacement in Seats.
Remove the door sill plate. Refer to Door Sill Plate Replacement .

Remove the 3 quarter trim panel retaining screws (1).
Starting at the lower edge of the trim panel and moving alternately clockwise and counterclockwise, pull outward on the trim panel to disengage the eight rear quarter trim panel attaching clips (2).
Remove the quarter trim panel from the vehicle.
Remove the 4 radio speaker grille speed clips (1), securing the speaker grille.
Remove the speaker grille (2).
Remove the rear quarter trim panel insulator (1), from the back of the quarter trim assembly (2).
Remove 7 rear quarter trim panel armrest retaining clips (1).
Remove 7 rear quarter trim panel armrest retaining nuts (2).
Gently pry the quarter trim panel armrest insert assembly (3), away from the rear quarter trim panel and remove.

You mite look for a video on youtube !

One of your hinges is messed up and the door is askew. Need to bend hinge back or replace it.

its in the HVAC heater core box,
how to remove it is a very long answer.
read the FSM on HVAC
or login to alldata.com see HVAC chapter, and read. it.
anyone can, not just me.

i see this on line,.

1. Disconnect and isolate the battery negative cable.
2. Remove first row seat.
3. Remove second row seat.
4. Remove sliding door sill trim panel.
5. Remove quarter trim bolster.
6. Remove D-pillar trim panel.
7. Remove first row seat belt anchor.
8. Remove second row seat belt anchor.
9. Remove screws attaching quarter trim to quarter panel from bolster area.
10. Remove screws attaching rear edge of quarter trim to attaching bracket.
11. Disengage hidden clips attaching front of quarter trim to quarter panel rearward of sliding door opening and at locators.
12. Remove quarter trim from quarter panel.
13. Disconnect speaker wire connector on LWB quarter trim panel with rear air conditioning.
14. Pass second row seat belt through slot in trim panel on long wheel base vehicle.
15. Pass first row seat belt through slot in trim panel.
16. Remove quarter trim panel from vehicle.
17. Remove the two screws that secure the top of the quarter trim panel attaching bracket to the quarter inner panel.
18. Remove the screw that secures the back of the rear heater-A/C unit housing to the right D-pillar.
19. Remove the screw that secures the front of the rear heater-A/C unit housing to the right quarter inner panel.
20. Carefully pull the top of the rear heater-A/C unit housing away from the right quarter inner panel far enough to reach between the rear heater-A/C unit housing and the quarter inner panel to access the blend door actuator.
21. Remove the two screws that secure the blend door actuator to the rear heater-A/C unit housing.
22. Pull the blend door actuator away from the rear heater-A/C unit housing far enough to disengage the actuator output shaft from the blend air door pivot.
23. Raise the blend door actuator far enough to access and disconnect the rear HVAC wire harness connector for the actuator from the actuator connector receptacle.
24. Remove the blend door actuator from between the rear heater-A/C unit housing and the quarter inner panel.

from autozone.com:

Removal & Installation

1. Disconnect and isolate the negative battery cable.
2. Remove the right quarter trim panel as follows:
   1. Remove first rear seat. Remove the second rear seat, if equipped.
   2. Remove the sliding door sill plate.
   3. Remove the quarter trim bolster.
   4. Remove the upper C-pillar trim and D-pillar trim panel.
   5. Remove the first and second rear seat belt anchors.
   6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
   7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
   8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

   
   

Fig. Removing the trim panel to access the rear blower motor

i. Disconnect the wiring harness connector from the accessory power outlet, if equipped.

j. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.

k. Pull first rear seat belt through the access hole.

l. Remove the quarter trim panel from the vehicle.

3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).

4. Twist the blower motor out of scroll housing.

5. Disconnect the blower motor wiring connector.

6. Remove the blower motor from vehicle.


Fig. The rear blower motor is held in place by four screws
To install:

1. Install the blower motor unit into the vehicle.
2. Reconnect the blower motor wiring connector.
3. Secure the blower motor into scroll housing.
4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
5. Install the right quarter trim panel as follows:
   1. Install the quarter trim panel in position in the vehicle.
   2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
   3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
   4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
   5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
   6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
   7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
   8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
   9. Install the D-pillar trim panel and upper C-pillar trim.
   10. Install the quarter trim bolster.
   11. Install the sliding door sill plate.
   12. Install the second rear seat, if equipped, and install the first rear seat.
       
6. Reconnect the negative battery cable. Check blower motor operation.

Removal & Installation

1. Disconnect and isolate the negative battery cable.
2. Remove the right quarter trim panel as follows:
   1. Remove first rear seat. Remove the second rear seat, if equipped.
   2. Remove the sliding door sill plate.
   3. Remove the quarter trim bolster.
   4. Remove the upper C-pillar trim and D-pillar trim panel.
   5. Remove the first and second rear seat belt anchors.
   6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
   7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
   8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.
      
      
      

      Fig. Removing the trim panel to access the rear blower motor
      

   9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
   10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
   11. Pull first rear seat belt through the access hole.
   12. Remove the quarter trim panel from the vehicle.
       
3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
4. Twist the blower motor out of scroll housing.
5. Disconnect the blower motor wiring connector.
6. Remove the blower motor from vehicle.
   
   
   

   Fig. The rear blower motor is held in place by four screws
   

To install:

1. Install the blower motor unit into the vehicle.
2. Reconnect the blower motor wiring connector.
3. Secure the blower motor into scroll housing.
4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
5. Install the right quarter trim panel as follows:
   1. Install the quarter trim panel in position in the vehicle.
   2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
   3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
   4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
   5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
   6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
   7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
   8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
   9. Install the D-pillar trim panel and upper C-pillar trim.
   10. Install the quarter trim bolster.
   11. Install the sliding door sill plate.
   12. Install the second rear seat, if equipped, and install the first rear seat.
       
6. Reconnect the negative battery cable. Check blower motor operation.

Hope helps (remember to rate this).

While all those parts are available, if there is really that much damage i'd say you may be better off looking for a new car. The doors and front fender bolt on, but the rear quarter panel is spot welded in MANY spots requiring a lot of work to properly replace. You will probably find the best overall deals at the local bone yards. You may be tempted to buy parts online but keep in mind shipping those heavy parts can cost as much as the part. You can use a site such as copartfinder.com to locate a junkyard near by that has the parts you need.

I have a 1990 camry and my driver side belt stopped working too. The problem is the wires that run from the door to inside the vehicle. Open your door, look in the doorjam for the black rubber piece. The wires inside it bend every time you open and close your door and eventually break. The only solution is to cut the rubber and resplice the wires which is a big pain in the ***. It took me a few frustrating hours, but, I heard it's easier if you take the door off. I left a lengthy amount of wire, wrapped in electrical tape, behind the front quarter panel to prevent it from bending again. This is a very common problem with camrys of these years.

Remove the sail panel,the little panel on inside of door at the mirror.
Remove the window regulator switch plate, pry up on the front of it with a small pick or screw driver. Disconnect the electrical connectors.
Remove the top door trim panel screw that is behind the sail panel you removed.
Remove door trim panel screw at window regulator switch plate opening.
Remove door trim panel screw in the courtesy lamp housing. Remove the courtesy lamp lens.Remove the screw.
Remove the inside door handle trim cover.
Remove the bolt.
Remove the inside door handle.
Lift upward to remove the front door trim panel.
Remove the courtesy lamp.
Turn the courtesy lamp bulb socket one quarter turn and remove.
Disconnect the power mirror electrical connector.
Remove the three outside rear view mirror nuts.
Remove the mirror.