Question about 2010 Hyundai Elantra

1 Answer

Hyundai elantra sunroof won't reset

Sunroof will not reset after following the reset procedure instructed in the manual. It stops a few inches short from closing and only the TILT button will close it completely

Posted by Christian on

  • 1 more comment 
  • Christian Jan 05, 2013

    Manual said I should push the OPEN button for 10 seconds until I heard the click (I did). Then release. Then within 3 seconds press again the OPEN button for another 5 seconds and let it go through the OPEN-CLOSE procedure. I released the OPEN button too early and since then it is messed up

  • Christian Jan 05, 2013

    Now the CLOSE button will make the sunroof close until about 2 inches from full closure. Then only the TILT will finish it off completely. If I then press OPEN nothing happens. If I press CLOSE it opens to about 2 inches. After that "OPEN" will pull it open all the way (and I think it is pushing it a little extra than usual)

  • Craig Mathis
    Craig Mathis Sep 10, 2015

    Did you find a solution to this. I'm experiencing the same thing.

×

Ad

1 Answer

tom

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Is the mechanical dirty if so maybe just a good cleaning will do hope this helps

Posted on Jan 05, 2013

Ad

5 Related Answers

Anonymous

  • 53 Answers

SOURCE: oil change procedure on a 2005 Hyundai elantra

This one is simple

1. Remove dip stick and filler cap.
2. Remove oil plug from oil pan and drain oil into an appropriate pan.
3. Remove and replace oil filter. (Filter will drain oil, just be aware to try and get it into the pan.
4. Refill oil. Start with 3.5 quarts, put cap and dip stick back on and start car, wait about 10 seconds and then turn off.
5. Check your dipstick for proper oil level.

And thats it you are done.

Posted on Jan 20, 2009

Ad

Anonymous

  • 69 Answers

SOURCE: MY SUNROOF WONT CLOSE

Check the owner's manual. There should be a section showing how to manually close the sunroof. You will use an allen wrench to turn the gears manually, I just don't know exactly what size or where the hole is located. It is typically located right behind the sunroof with a plug covering the hole in the headliner.

Posted on May 27, 2009

Anonymous

  • 10 Answers

SOURCE: Check Engine Light is On 2006 Hyundai Elantra 13,000 miles

An easy fix, if the check engine light is on find an Auto Advance, they can clear the code for you. Any auto parts store may be able to as well, Auto Zone is another one that may be able to help.

Posted on Nov 22, 2008

localwonder

Michael Masters

  • 6784 Answers

SOURCE: How do you reset the airbag light for a 1996 hyundai elantra?

The air bag light can only be reset by a diagnostic CPU or the local dealer ship.

Posted on Jun 21, 2009

Anonymous

  • 1 Answer

SOURCE: Interior sunroof shade is stuck closed

a solution that i had is that if you can open your sunroof without it opening ur shade try that then fold the shade by pushing between or in the middle of it and popout the shade. this works but try not to push to hard or you can break the plastic runners on the side of the shade. check to see if nothing is in the way of the runners. then put back the back part first then slide it all the way to the back then, do the other part and clip them back together  (there might be a little metal piece that pushes your shades back so check that first to see if its there first)

Posted on May 06, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sunroof is stuck open and tried to reset it by holding button down for ten seconds and then it moves about half an inch and stays fully open. What do I need to do to get it to close?


Hi Thomas , First you should have it diagnosed by someone who has the tool to do so ! upscale scan tool , factory scan tool !
Diagnostic Starting Point - Roof
Begin the diagnosis with the Diagnostic System Check - Power Sunroof . The Diagnostic System Check will provide the following information:
?€¢
The identification of the control modules which command the system


?€¢
The ability of the control modules to communicate through the serial data circuit


?€¢
The identification of any stored DTCs and their status

The use of the Diagnostic System Check will identify the correct procedure for diagnosing the system and where the procedure is located.
Symptoms
When no DTCs ( diagnostic trouble codes ) are present, begin symptom diagnosis by reviewing the
Sunroof Description and Operation . Reviewing the Description and Operation information will help you determine the correct symptom diagnostic procedure when a malfunction exists. Reviewing the Description and Operation information will also help you determine if the condition described by the customer is normal operation. Refer to Symptoms - Roof in order to identify the correct procedure for diagnosing the system and where the procedure is located.
Important: If the suspected cause of an inoperative sunroof is a power interruption to the sunroof module, the sunroof must be re-initialized. Refer to Sunroof Motor/Actuator Synchronization .
Important: The following must be completed before using the symptom tables.

  1. Perform Diagnostic Starting Point - Roof in order to verify that all of the following are true:
  2. ?€¢
    There are no DTCs set.


    ?€¢
    The control module(s) can communicate via the serial data link.

  3. Review the system operation in order to familiarize yourself with the system functions. Refer to Sunroof Description and Operation .
Visual/Physical Inspection
?€¢
Inspect for aftermarket devices which could affect the operation of the Power Sunroof system. Refer to
Checking Aftermarket Accessories in Wiring Systems.


?€¢
Inspect the easily accessible or visible system components for obvious damage or conditions which could cause the symptom.

Intermittent
Faulty electrical connections or wiring may be the cause of intermittent conditions. Refer to
Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
Symptom List
Refer to a symptom diagnostic procedure from the following list in order to diagnose the symptom:
?€¢
Power Sunroof Inoperative


?€¢
Power Sunroof Does Not Open to Express Position


?€¢
Retained Accessory Power (RAP) On After Timeout in Retained Accessory Power, if the power sunroof should operate longer than 20 minutes after the ignition has been turned OFF


This information is right out of GMC service repair manual !
Sunroof Motor/Actuator Synchronization
Synchronization will be necessary anytime the sunroof module battery positive voltage circuit is interrupted. The sunroof module will be synchronized when the controller learns the full vent position. The sunroof system will ignore any open request until the system has been synchronized.
To synchronize the sunroof:

  1. Turn ON the ignition, with the engine OFF.
  2. Using the close/tilt up portion of the sunroof switch, operate the sunroof glass until it reaches the full vent position.
  3. Verify that the system operates normally.
Once the sunroof glass reaches the full vent position, the actual position is stored in the memory of the sunroof module. The sunroof module will stop the motor one motor revolution before the defined actual positions.

Mar 24, 2015 | 2004 GMC Yukon XL

Tip

Mazda3 Sunroof Adjustments & Repairs


Folks -

The "gearbox" is unfortunately under the headliner with no easy access. If you are also experiencing a clicking sound when the motor is activated, the regulator track had slipped position and will need to be reset.

http://img696.imageshack.us/img696/2781/roofadj04.jpg
IMAGE WONT POST, SORRY

Removing the map light assembly (process below) may help in your initial diagnosis, you can feel the motor mounting screws and the motor assembly to determine if their loose.

http://img696.imageshack.us/img696/8415/roofadj03.jpg
IMAGE WONT POST, SORRY

I have been through this problem twice now. The first time the motor / gearbox came loose from it's mounts, began slipping (click, click,click), very nasty sound. I remounted the motor with threadlock on the NEW ALLEN HEAD screws, but alas.. two years later (mine's 2006) it slipped again.. I need to drop the headliner once more and have a look. If you would like a copy of your 05/06 FSM, drop me a line.


Here's the RESET procedure from the FSM, absolutely gospel, no other way to fix it:

Sunroof Motor Assembly Note:

Note
• If the guide is removed, initial position setting of the sunroof motor will be required. After installing the sunroof unit, perform initial position setting using the following procedure.

1. Press the TILT UP switch to fully tilt up the glass panel.

2. When the glass panel reaches the fully tilt up position, temporarily release the TILT UP switch and press it again for approx. 13 s continuously. Continue pressing the switch until the glass panel automatically stops at the fully tilt up position after reaching the mechanical lock position.

3. When the glass panel stops at the fully tilt up position, temporarily release the TILT UP switch, then press it again within 5 s and hold.
Note

• Press the TILT UP switch continuously until the glass panel opens to the fully open position, returns to the fully closed position and then stops.

4. Release the TILT UP switch when the glass panel stops at the fully closed position.


ALSO, Here's the clearance adjustment specs for having the glass panel in the correct resting position:

GLASS PANEL ADJUSTMENT

1. Fully close the glass panel.

2. Measure the gap and height difference between the glass panel and the body.

3. Loosen the glass panel installation screws and move the glass panel to adjust.

http://img696.imageshack.us/img696/3097/roofadj01.jpg
IMAGE WONT POST, SORRY

Standard clearance a: 0.2-2.2 mm {0.008-0.08 in} b: 0 mm {0 in}
4. Tighten the screws.

5. Insert any available thin plastic card between the weatherstrip and the body, and verify that they are sealed. (There is resistance when the plastic card is moved.)

http://img696.imageshack.us/img696/610/roofadj02.jpg
IMAGE WONT POST, SORRY

• If they are not sealed, perform Steps 3-4 and adjust again.

MAP LIGHT REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.

2. Insert a tape-wrapped flathead screwdriver into the gap between the headliner and the map light.

3. Press the tab and remove the map light.

http://img94.imageshack.us/img94/2121/roofadj05.jpg
IMAGE WONT POST, SORRY

4. Disconnect the map light connector.

http://img696.imageshack.us/img696/3024/roofadj06.jpg
IMAGE WONT POST, SORRY

5. Remove the socket, then remove the map light bulb.

6. Install in the reverse order of removal.

SUNROOF UNIT DISASSEMBLY/ASSEMBLY

1. Disassemble in the order indicated in the table.

2. Assemble in the reverse order of disassembly.

http://img268.imageshack.us/img268/9769/roofadj07.jpg
IMAGE WONT POST, SORRY

1 Screw A
2 Drip rail
3 Sunshade stopper
4 Screw B
5 Sunshade
6 Deflector
7 Screw C
8 Sunroof motor
9 Rear drip
10 Guide
11 Decoration link
12 Front drip
13 Tape protector
14 Short cord
15 Frame

on Jan 01, 2010 | Mazda MAZDA3 Cars & Trucks

1 Answer

Reset sunroof toyota


To reset the moonroof one-touch operation:
With ignition switch in the "ON" position, do the following:
1. Push and hold the "TILT UP" side of the switch until the moon roof tilts all the way up and then tilts down slightly (approximately 10 mm [0.39 in.] at the rear).
2. Check for proper operation of the "one-touch slide open/close" and "one-touch tilt up/down" functions by pushing the switch briefly to the "SLIDE OPEN" and
"TILT UP" positions.

Mar 21, 2014 | 2008 Toyota Corolla

1 Answer

My sunroof on my 2002 honda accord wont open but it opens to the tilt and it can close. is there a fuse or something to why it wont open all the way


Try resetting,this works on many cars
Press and hold tilt,watch sunroof untill it raises another half inch
Close tilt and test slide

Jun 18, 2010 | 2002 Honda Accord

1 Answer

My 1990 Maxima's sunroof will slide up and shut,


Is there a way to manually close the sunroof in the up position on a 98 Nissan Maxima?

May 17, 2010 | 1990 Nissan Maxima

1 Answer

2005 mazda 3 sunroof


H Kim -

The "gearbox" is unfortunately under the headliner with no easy access. If you are also experiencing a clicking sound when the motor is activated, the regulator track had slipped position and will need to be reset.

I have been through this problem twice now. The first time the motor / gearbox came loose from it's mounts, began slipping (click, click,click), very nasty sound. I remounted the motor with threadlock on the screws, but alas.. two years later (mine's 2006) it slipped again.. I don't know why yet, I need to drop the headliner once more and have a look. If you would like a copy of your FSM, drop me a line.

Here's the RESET procedure from the FSM, absolutely gospel, no other way to fix it:
Sunroof Motor Assembly Note: Note • If the guide is removed, initial position setting of the sunroof motor will be required. After installing the sunroof unit, perform initial position setting using the following procedure. 1. Press the TILT UP switch to fully tilt up the glass panel.
2. When the glass panel reaches the fully tilt up position, temporarily release the TILT UP switch and press it again for approx. 13 s continuously. Continue pressing the switch until the glass panel automatically stops at the fully tilt up position after reaching the mechanical lock position.
3. When the glass panel stops at the fully tilt up position, temporarily release the TILT UP switch, then press it again within 5 s and hold.
Note • Press the TILT UP switch continuously until the glass panel opens to the fully open position, returns to the fully closed position and then stops. 4. Release the TILT UP switch when the glass panel stops at the fully closed position.



ALSO, Here's the clearance adjustment specs for having the glass panel in the correct resting position:


GLASS PANEL ADJUSTMENT
1. Fully close the glass panel.
2. Measure the gap and height difference between the glass panel and the body.
3. Loosen the glass panel installation screws and move the glass panel to adjust.


Standard clearance a: 0.2-2.2 mm {0.008-0.08 in} b: 0 mm {0 in} 4. Tighten the screws.
5. Insert any available thin plastic card between the weatherstrip and the body, and verify that they are sealed. (There is resistance when the plastic card is moved.)


• If they are not sealed, perform Steps 3-4 and adjust again.

Aug 31, 2009 | 2001 Mazda Tribute

1 Answer

03 Tiburon sunroof


Either motor or relay is bad.

Jul 20, 2009 | Hyundai Tiburon Cars & Trucks

2 Answers

Sun roof does not work


Dear cz50001: there are only a few things that you, a weekend warrior can do to diagnose and/or fix the problem on your car.
Unfortunately the newer cars get, the more complex they get.
Unfortunately, your car is one which falls in the more complex category. Your car is designed with a "BODY CONTROL MODULE". This little gem gets input from nearly every electrical component in the car including the sunroof. In terms of what you can do to check it out: The fuse box inside the car has roughly 24 fuses positioned vertically 12x12. The fuse located at the lower left side of the box is a 10A "red in color" is for the sunroof. Remove it and look through it to see if it has been burned through the center. If it has, replace it and try the sun roof. If the fuse blows again, you have a short and it would be best left to a professional.
There is another set of circumstances which can occur that will render the sunroof inoperable. If the battery is disconnected or if the sunroof motor had been disconnected, the sunroof will stop operating. To reset the sunroof memory, with the key in the on position, push and hold the sunroof tilt switch in the forward (up) position until the sunroof is fully vented (tilted up) position. It should at that point operate normally. Should those two suggestions not solve your problem, it requires either a dealership with a specialized tool called CONSULT-11 to communicate with the BCM. There are some specialty shops such as mine equipped to deal with your car as well. However, most can not address this type of problem without this diagnostic tool. Good luck.

Apr 05, 2009 | 2005 Nissan Altima

2 Answers

2005 nissan maxima sunroof won't open


Had this problem all you have to do is actually open sunroof with tilt button all the way and then close it with tilt button to reset, then it should work with open switch. If you disconnect battery this happens and you have to reset it this way

Feb 28, 2009 | 2004 Nissan Maxima

1 Answer

2003 maxima sunroof won't close


Sounds like the sunroof motor is out of time. Needs to be re-timed. There is a retime procedure, (that I would try first) but I don't remember the whole procedure. if you still have the problem, let me know and i will get the whole thing , from the service manual.

Jul 20, 2008 | 2003 Nissan Maxima

Not finding what you are looking for?
2010 Hyundai Elantra Logo

2,460 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

Brad Brown

Level 3 Expert

18564 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...