2002 izuzu rodeo 3.2 liter serpentine belt diagram

https://www.youtube.com/watch?v=rnmQJ8owA24

Search Results

images for diagram on how to replace a serpentine
How To Install Replace Serpentine Belt Oldsmobile Alero 99 ...? 3:33https://www.youtube.com/watch?v=jkzXTt43uwwFeb 9, 2012 - Uploaded by 1A Auto PartsHow To Install Replace Serpentine Belt Oldsmobile Alero 99-04 2.4L .... There should be a belt routing diagram on the frame rail or under side ...serpentine belt install 3.1/ 3.4 v6 - YouTube? 4:00https://www.youtube.com/watch?v=GYoWuvEZ2DcMay 6, 2013 - Uploaded by JoeTheAutoGuythis a serpentine belt install video on a 3.1 liter gm v6 , 3.4 liters are the same in ... Replacing the alternator or serpentine on anyOldsmobile Alero 99-04 3.4 Liter ... Serpentine Belt Replacement 1995-2005 Chevrolet Cavalier .

http://www.2carpros.com/diagrams/plymouth/voyager/1991 Here are the diagrams.

Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.

3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.

4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.

5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.

6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

here is some info

http://www.2carpros.com/diagrams/isuzu/rodeo/2002

Buy the guide on it, it's like 20-30 bucks and that's all you'll ever need to know about problems and how to know what's wrong.

On all vehicles since 1984 the v-belt/serpentine belt routing diagram has been on the inside of the hood or on the radiator cross member.

You didn't list your motor size so please pick the applicable diagram:


Accessory serpentine belt routing—4.8L, 5.3L & 6.0L engines


Accessory serpentine belt routing—5.7L engines with A/C


Accessory serpentine belt routing—5.7L engines without A/C


Accessory serpentine belt routing—6.5L Diesel engines


Accessory serpentine belt routing—7.4L engines


Accessory serpentine belt routing—8.1L engines

Below is the diagram you requested. Kindly return to rate this solution and thank you for using Fixya!
Greg

Go to your local library and get a Chiltons book and photocopy the diagram from that.