Question about 2010 BMW 3 Series

1 Answer

Windshield washer do not work on my 2010 bmw328 what could be problem but wipers function

Wipers do work except for the washer on front windshield

Posted by tony diego on

Ad

1 Answer

Nyan cat

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Its probally rusty or something it gets used out how old is it get it checked or replaced

Posted on Dec 17, 2012

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I HAVE A 2008 SATURN VUE 3.5 WIPERS WILL NOT PARK OR SHUT OFF OR WILL PARK ANYWHERE I HAVE REPLACED MOTOR AND SWITH STILL HAVE PTOBLEM


Your windshield wiper's are computer controlled by the BCM - body control module . The wiper switch is an input to the BCM , which energizes two different relay's to turn on the wiper's . Taking the vehicle to a qualied repair shop an having diagnostic's run would be your best bet , unless you have a professional scanner that can read DTC'S - diagnostric trouble code's in the BCM !
DTC B3715 00: Front Wiper Relay Drive Circuit
DTC B3875 00: Wiper High Speed Relay Circuit
DTC B3922 00: Front Wiper Function Select Circuit
This is always the first step in the diagnostic process . An if you do not know how they work ,reading factory service manual info. should be done .
Circuit/System Description
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation.
Your best bet , take it to a qualified repair shop.

Dec 10, 2017 | Saturn Cars & Trucks

1 Answer

WHERE IS THE WIPER/WASHER FUSE LOCATED ON 2007 PONTIAC TORRENT


In the under hood fuse box , should have diagram inside the lid . Front wiper's or rear ? Front fuse # 36 - 25 amp. Plus Two relay's PCB hi and Wiper PCB relay . Wouldn't think this being fuse problem . Wiper switch , motor etc... The wiper's are control by a computer . BCM - body control module .

The windshield wiper/washer system consists of front and rear wipers. The front and rear wipers are operative when the vehicle is in accessory or run. The front wipers have 4 different modes: Mist, Intermittent, Low, and High. When the front wipers are in the intermittent mode, there are 5 delay modes to chose from, commanded by the windshield wiper washer switch through the body control module (BCM). The rear wipers has an only one mode.

If the fuse is bad , could have a short to ground or wiper motor pulling to much current (amps) . Fuse's don't just blow for no reason ! Could also have DTC'S - diagnostic trouble codes stored in the BCM .
DTC B3715
DTC B3873
DTC B3875
DTC B3922

DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation.
The BCM controls the windshield wiper motor through two output controls, controlling two different PCB relays which control the desired wiper speed, high or low.
DTC B3922 00: Front Wiper Function Select Circuit

The PCB relay's are non- servicable , replace fuse box . Soldered in Your best bet mit be to take it to a qualified repair shop .

Feb 20, 2017 | Pontiac Cars & Trucks

1 Answer

Where is fuse for 1997 mercury wagon for windshield wipers


1997 mercury wagon ? Sable ? VISUAL INSPECTION CHART-WINDSHIELD WIPER AND WASHER SYSTEMS Mechanical Electrical
  • Windshield wiper blade missing or damaged.
  • Binding windshield wiper pivot arm.
  • Binding windshield wiper mounting arm and pivot shaft.
  • Empty windshield washer reservoir.
  • Kinked or broken windshield washer hoses.
  • Open fuse junction panel Fuses:
    • 8 (5A)
    • 12 (5A)
    • 20 (5A)
    • 23 (5A)
  • Damaged windshield wiper motor.
  • Damaged windshield washer pump.
  • Open connectors.
  • Corroded connectors.
  • Inoperative multi-function switch.
  • Open thermal breaker internal to the wiper motor

Which are not working , front , back or all ?

I/P Fuse Panel C225
Under left corner of instrument cluster

Feb 05, 2017 | Mercury Cars & Trucks

1 Answer

2003 Pontiac Montana wipers not working how to fix


First you need a wiring diagram, free at http://www.bbbind.com/free_tsb.html Then you need a DVOM - digital volt ohm meter to test the circuit . Then if your not familiar with automotive electrical systems testing ,go on youtube an check out Electric Testing Techniques You Need to Know Also having a factory diagnostic trouble shooting chart would also be usefull . You could just start replacing parts , you mite get lucky . The wiper motor is a high fail part , so is the switch ..You could find the fuse is blown ! But fuse's don't usually blow without a reason . Short to ground , low resistance . ( high current flow) Also knowing how they work and what all is involved in making them work.
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Windshield wiper motor module
• Windshield wiper motor
• Windshield washer pump motor
• FRT/WPR/WSHR 25A fuse

Wiper/Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls wiper motor operation. The windshield wiper motor is a 2 speed motor and is operated at low speed in all modes except HIGH. The accessory voltage supply circuit to the windshield wiper motor assembly is used to operate the wiper motor in all of the low speed modes. The accessory voltage supply circuit to the windshield wiper/washer switch is used to supply the windshield wiper switch signal circuits and the wiper motor high speed circuit.
When the wiper/washer switch is in the LOW position voltage is supplied through a 24K ohm resistor within the switch to the windshield wiper switch signal 2 circuit, and accessory voltage is supplied to the windshield wiper switch signal 1 circuit. The reduced voltage from the wiper switch signal 2 circuit and accessory voltage from the wiper switch signal 1 circuit causes the wiper motor module to close the wiper motor accessory voltage supply circuit to the wiper motor low speed terminal.
Windshield wiper/washer system MIST operation is identical to LOW operation except that the MIST switch is a press and release type. When the wiper switch is moved to the MIST position and released, low speed wiper motor operation is started and will continue until 1 cycle is complete. If the wiper switch is moved to the MIST position and held, the windshield wiper motor will operate in the LOW mode until the switch is released.

Don't the wipers work in any mode ?
1
Did you review the Wiper/Washer System description and operation and perform the necessary inspections?
YES - Go to Step 2
NO - Go to Symptoms - Wiper/Washer Systems
2
Turn ON the ignition , with the engine OFF.
Operate the windshield wiper/washer switch through all the switch positions.
Does the windshield wiper/washer system operate normally?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn OFF the ignition.
Disconnect the harness connector of the windshield wiper motor.
Turn the ignition ON, with the engine OFF.
Connect a test lamp from the accessory voltage circuit of the windshield wiper motor to a good ground.
Does the test lamp illuminate?
YES - Go to Step 4
NO - Go to Step 13
4
Connect a test lamp from the accessory voltage circuit to the ground circuit of the windshield wiper motor.
Does the test lamp illuminate?
YES - Go to Step 5
NO - Go to Step 14
5
Connect a test lamp from the signal 2 circuit of the windshield wiper switch to a good ground.
Press the windshield washer switch.
Does the test lamp illuminate?
YES - Go to Step 11
NO - Go to Step 6
Let me know if you make it this far and i will send rest of diagnostic's

Nov 25, 2016 | 2003 Pontiac Montana

1 Answer

In my 2007 Saturn Vue there is what I think is an air pump which is cracked that one port is not connected to anything.


There is a electric motor that pumps washer fluid . Located in the bottom of the washer fluid tank .
Wash Operation (Front and Rear Wipers)
The front and rear washer systems use the same windshield washer fluid pump. When either the front or rear wiper is in the washer position voltage will be supplied to one side of the windshield washer fluid pump (depending on whether it is front or rear), while the other side of the pump is grounded.
At this point, the windshield washer fluid pump sprays solvent onto the windshield. When the front or rear washer is activated, the BCM receives an input from the switch that is activated. The BCM will control the wipers while in the WASH mode. The BCM will control either the front wiper relay or the rear wiper relay to turn on the wipers. The windshield wipers operate at low speed for 3 swipes and returns to the park position.

When turning on the washers do you hear the motor run ? Have some one try it while you listen at the washer fluid tank ! These pump motors do go bad .
turn OFF the ignition.
Disconnect the harness electrical connector of the windshield washer fluid pump.
Connect a test lamp from the windshield washer pump control circuit to a good ground .
Turn ON the ignition, with the engine OFF.
Press the front washer switch.
Does the test lamp illuminate?
YES or NO !

Nov 18, 2016 | Saturn Cars & Trucks

1 Answer

My front windshield wipers will only work on high. Any suggestions?


Search Results

    My windshield wipers only work on high speed...? ' Yahoo Answers

    https://answers.yahoo.com/question/index?qid...
    Nov 11, 2006 - My windshield wipers only work on high speed. ... If it's the compound switch on the lever on the steering wheel, it can be a bit complicated to ...

    Windshield wipers - CarGurus

    www.cargurus.com > Questions > Mercury > Grand Marquis

    CarGurusMay 19, 2015 - Windshield wipers - My wipers stopped last week and the next day they ... slow or intermitt and only work on high speed and the washer wiper doesn;twork ... The LCM does not effect the operation of the motor or switch it just ...

    Windshield Wipers only working at highest setting - Ford Flex Forum

    www.fordflex.net > ... > General Ford Flex Discussions
    Feb 16, 2011 - Windshield Wipers only working at highest setting ... rear wiper worksjust fine, just the front wipers only work at highest setting. ... the wipers sometimes grinds out the gears thus only working at high sppeds. If it is the motor or Transmission for the wipers, can I fix this myself and how much would it cost me.

    Common GM Wiper Problem - YouTube

    ? 3:23
    https://www.youtube.com/watch?v=kc6e2Tmar68
    Oct 25, 2010 - Uploaded by roadragecustoms
    The windshield wipers only worked occasionally. ... My 1998 dodge ram wipers only work on high will this help me? thanks.... Express van. you have to take out the motor and the transmission from under the front of the van..

Feb 09, 2016 | Cars & Trucks

1 Answer

Where is the windshield washer motor fuse located ?


images for 2009 Nissan Rogue SL Where is the

Windshield Wiper Pump - Not working - Nissan Forum ' Nissan Forums

forums.nicoclub.com/windshield-wiper-pump-not-working-t581434.html
Oct 22, 2013 - Year of vehicle -- 2011 Nissan Rogue SL Leather/Nav Package ... rather an engineer and found that my windshield washer pump was not ... sprocket: Posts: 150: Joined: Thu Jun 11, 2009 1:27 pm: Location: Metro Detroit, MI ... windshield washer fluid switch backwards ?
Apr 27, 2012
Windshield WASHFLUID ISSUE!
Dec 11, 2009
Front windshield sprayers not working..AHH!!!
Nov 10, 2009
More results from forums.nicoclub.com

Jan 11, 2016 | 2009 Nissan Rogue SL

2 Answers

What would cause the windshield wipers on my recently purchased Jeep Patriot Sport work on every speed except the high speed. High speed doesn't work at all.


The intermittent switch has a bad contact in it for the high speed, i would say, most likely will have to replace it.

Sep 15, 2014 | 2008 Jeep Patriot Sport

1 Answer

My 2005 Jeep Grand Cherokee's windshield washer is not working.


Check power at the pump motors. You may not see a fuse because some run off a circuit breaker. If all else fails, a bit "backyard" but you likely could break out the washer pumps from the system and make a simple push button on the dash to operate them.

Jul 08, 2009 | Jeep Grand Cherokee Cars & Trucks

Not finding what you are looking for?
2010 BMW 3 Series Logo

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

gbob59

Level 3 Expert

3063 Answers

old marine
old marine

Level 3 Expert

2325 Answers

randymanfive

Level 3 Expert

501 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...