2001 Jaguar S-Type Logo
Posted on Dec 11, 2012
Answered

Bearring replacement cost on a 2001 jaguar s type

How much does it cost to replace the wheel bearrings on my '01 jaguar stype

Answer This Question

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.
Corporal:

An expert that has over 10 points.
Problem Solver:

An expert who has answered 5 questions.

  • Contributor 5 Answers
  • Posted on Dec 11, 2012
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.
Corporal:

An expert that has over 10 points.
Problem Solver:

An expert who has answered 5 questions.

Joined: Dec 11, 2012
Answers
5
Questions
0
Helped
694
Points
15

42 dollars, 31 for front go on autopartswarehouse.com

4 Related Answers

Anonymous

  • 52 Answers
  • Posted on Jan 15, 2009

SOURCE: front wheel bearings

www.rockauto.com if your in the states. you can buythe bearing or the assembly
hope this helps

Ad

Anonymous

  • 52 Answers
  • Posted on May 11, 2009

SOURCE: how to replace rear wheel bearing on s type jaguar v reg

pretty basic the same and any other wheel bearing. But you need a hydraulic press, if you dont have one of those then their is just no way that you will be able to do it.

If it is newer than an 05 you need to take it to the dealership, because they need to hook up their computer and electronically disengage the rear parking brakes by putting it into service mode.

SPEEDY CAR WORK SHOP

  • 489 Answers
  • Posted on Sep 22, 2009

SOURCE: I have Jaguar XJR 2001. How do I replace Blower

Driver side :
1- Remove upper steering column 2- Remove driver stowage compartment 3- Remove driver's footwell duct 4- Remove cable tie 5- Remove duct connecting blower assemble to heater/cooler unit 6- Disconnect harness connector from blower assembly 7- Remove blower assembly.
Install in reverse order. Tighten nuts to 5-7 Nm
Passenger side :
1- Remove Instrument panel 2- Remove passenger footwell duct 3- Disconnect harness connector from blower assembly 4- Remove festeners securing duct to heater/cooler unit 5- Remove duct connecting connecting blower to heater/cooler unit 6- Remove blower assembly
Install in reverse order. Tighten nuts to 5-7 Nm

Anonymous

  • 61 Answers
  • Posted on Nov 09, 2009

SOURCE: How to fit a wheel bearing on an s type jaguar

My friend;
Try this;

  1. Remove the tire assy.
  2. Remove the cotter pin inside the nut holding the wheel hub assy.
  3. Remove the nut holding the wheel hub assy.
  4. Remove the wheel hub assy. & if there is circlips {Retaining} holding the bearings snap them by small slotted screwdriver.
  5. Install the bearings in the wheel hub assy.
Reverse the Removal process to Install the removed parts.
 Or consult the internet Jaguar Forums.
 Try it, & PLZ; let me know if I add any benefits to you.
I hope I add some thing valuable to you.
Regards;
MAR;
[email protected]

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0answers

Looking for location of oil sending unit location on 03 jaguar x type 2.5l
Read full answer
Be the first to answer Nov 23, 2015 • Jaguar Cars & Trucks
1helpful
1answer

Recently had a front wheel collapse onmy s type jaguar ive had it fixed but the DSC light is on and ABS is coming on under breaking on drivers side front wheel any ideas
the jaguar front wheel bearing comes complete with a abs sensor and bearing cover if someone has removed the cover it sounds like the air gap between sensor and the reluctor ring is to great or has someone renewed just bearing and not the hub unit like you are ment to do? have a good look at the rear of the bearing cover.
Read full answer
Mar 29, 2013 • 2001 Jaguar S-Type
0helpful
1answer

I have a really loud humming noise in Tue rear end of my 03 JAG s type just wondering what could be the issue here?
I can almost assure you its a rear wheel hub bearing.It will have to be replaced at a shop...Job will cost about 4-500.00 bucks..The s types are notorious for this.The bearing will usuall make the noise as you go into the corner turns and if you turn in the opposing side wheel the sound will go away until you go into a straight line.They will usual take a stethascope while the car is on the rack and place it in drive to pin point the bearing.Good luck..
Read full answer
Aug 03, 2011 • 2003 Jaguar S-Type
3helpful
1answer

How to replace a Jaguar X Type fron wheel bearing
Jaguar 2000-06

Wheel Bearings
Removal & Installation
  1. Remove the brake disc.
  2. Remove and discard the retaining clip. Detach the ABS sensor.
  3. Remove and discard the O-ring seal.
  4. Remove the wheel hub and bearing retaining bolts.
  5. Remove the wheel hub and bearing.
  6. Prior to applying sealer, clean the ABS sensor sealing surface and the ABS sensor aperture sealing surface.
  7. Install a new O-ring seal.
  8. Apply a 2.5mm bead of Loctite Ultra Blue 587 Silicone (RTV) sealer to the ABS sensor sealing surface.
  9. Install a new ABS sensor retaining clip.
  10. Install the hub/bearing assembly. Tighten to 90 Nm.

  1. Remove wheel knuckle.
NOTE When removing the wheel hub from the wheel knuckle the bearing will be destroyed and the bearing inner ring will remain on the wheel hub.
d752c5a.jpg

Fig. Using special tools, remove the wheel hub-X-Type
  1. Using special tools, remove the wheel hub.
  2. Using a suitable tool, remove the bearing inner ring.
  3. Using special tools, remove the wheel bearing.
    4. 2125147.jpg

    Fig. Using a suitable tool, remove the bearing inner ring-X-Type

    ee51ce7.jpg

    Fig. Using special tools, remove the wheel bearing-X-Type

To install:

b506586.jpg

Fig. Insert special tool 204-312 in to 204-309-X-Type
  1. Insert special tool 204-312 in to 204-309.
  2. Support the wheel knuckle on special tools.
NOTE Make sure wheel bearing is correctly orientated with the colored side facing inboard.
  1. Align the bearing over special tool.
  2. Using special tools, press bearing into wheel knuckle.
  3. Change special tool 204-312 to 204-313.
  4. Align the bearing and wheel knuckle over special tool.
  5. Slide wheel hub over the guide and align to the bearing.
  6. Using special tools install the wheel hub.
  7. Install the wheel knuckle.

    8. 5a457fa.jpg

    Fig. Using special tools, press bearing into wheel knuckle-X-Type

    b9fcc3f.jpg

    Fig. Change special tool 204-312 to 204-313-X-Type

    be319f2.jpg

    Fig. Align the bearing and wheel knuckle over special tool-X-Type

    8a9e0dc.jpg

    Fig. Slide wheel hub over the guide and align to the bearing-X-Type
  1. Raise front of vehicle and support on stands.
  2. Remove appropriate road wheel.
  3. Using wire or string, secure brake caliper to road spring to take weight off brake hose.
  4. Raise vehicle sufficient to provide access for special tool 204-111.
  5. Install special tool 204-111 in road spring.
  6. Slacken tool adjuster to suit spring length.
  7. Install adaptor and thrust collar.
  8. Position stem of tool in center of spring passing dowel through slot in suspension turret.
    9. 24ce878.jpg

    Fig. Install special tool 204-111 in road spring-XJ Range and XK Range

    1d0063e.jpg

     Fig. Position stem of tool in center of spring passing dowel through slot in suspension turret-XJ Range and XK Range

NOTE When turning tool adjuster, ensure that tool stem does not rotate and disturb position of dowel in suspension turret.
  1. Engage dowel of special tool 204-111 in suspension turret and rotate to position across slot.
  2. Lower vehicle onto stands.
  3. Rotate tool adjuster to tension spring.
  4. Remove wheel speed sensor securing screw and withdraw sensor from vertical link.
  5. Remove nut securing tie rod outer ball joint to steering arm.
  6. Release ball joint from vertical link.
  7. Install special tool 211-098 on tie rod outer ball joint.
  8. Tighten tool bolt to release taper pin from vertical link.
  9. Remove special tool from ball joint and position tie rod for access.
  10. Remove nut securing upper control arm ball joint to vertical link.

    11. 3af9a83.jpg

    Fig. Install special tool 211-098 on tie rod outer ball joint-XJ Range and XK Range

continue...
Read full answer
Aug 03, 2010 • 2002 Jaguar X-Type
1helpful
1answer

What is the approximate cost to replace a front wheel bearing?
depends on what kind of vehicle it is on. if it is just the bearing and race, about a hundred bucks. if it is the hub bearing type u are probably looking at more like 250.
Read full answer
May 12, 2010 • 2001 Ford Escape
1helpful
1answer

How to fit a wheel bearing on an s type jaguar 1999
My friend;
Try this;
  1. Remove the tire assy.
  2. Remove the cotter pin inside the nut holding the wheel hub assy.
  3. Remove the nut holding the wheel hub assy.
  4. Remove the wheel hub assy. & if there is circlips {Retaining} holding the bearings snap them by small slotted screwdriver.
  5. Install the bearings in the wheel hub assy.
Reverse the Removal process to Install the removed parts.
 Or consult the internet Jaguar Forums.
 Try it, & PLZ; let me know if I add any benefits to you.
I hope I add some thing valuable to you.
Regards;
MAR;
[email protected]
Read full answer
Nov 09, 2009 • 2000 Jaguar S-Type
1helpful
1answer

Jaguar S Type 2001 . Few days ago I start hearing a constant noise while driving ( like someone is driving a mini scooter ), coming possibly from front right wheel. There is no noise when car is moving...
is it a humming sound? does it get quiter or stop when you tur? if you answered yes to these then it is the ball bearing
Read full answer
Jun 20, 2009 • 2001 Jaguar S-Type
0helpful
2answers

2000 s-type jaguar I need a wheel bearing how hard and exspensive is this problem and will the car still run if I dont fix the problem
Not sure on the price but, NO DO NOT DRIVE ON BAD BEARINGS.
Read full answer
Mar 07, 2009 • 2000 Jaguar S-Type
3helpful
1answer

How to replace rear wheel bearing on s type jaguar v reg
pretty basic the same and any other wheel bearing. But you need a hydraulic press, if you dont have one of those then their is just no way that you will be able to do it.

If it is newer than an 05 you need to take it to the dealership, because they need to hook up their computer and electronically disengage the rear parking brakes by putting it into service mode.
Read full answer
Jan 28, 2009 • 2001 Jaguar S-Type
0helpful
1answer

Front wheel bearings
www.rockauto.com if your in the states. you can buythe bearing or the assembly
hope this helps
Read full answer
Jan 12, 2009 • 2001 Jaguar S-Type
Not finding what you are looking for?

View Most Popular

2001 S-Type

  • Cars & Trucks

Related Question

Looking for location of oil sending unit location on 03 jaguar x type 2.5l

  • Jaguar Cars & Trucks

Related Topics

349 views

Ask a Question

Usually answered in minutes!

Popular Questions

Gearbox fault of Jaguar S Type

2000 Jaguar S-Type

Parking brake will not disengage on 2005 jaguar s type

2005 Jaguar S-Type

S type jaguar parking brake warning that brake

2002 Jaguar S-Type

Jaguar s-type restricted performance

2003 Jaguar S-Type

Rear pad replacement on a Jaguar S-Type

2001 Jaguar S-Type

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Jaguar Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...