Power steering hose part number for 4g93t - 2002 Mitsubishi Lancer

The Hose is here, but I notice you say 2009 AND 2002. It can't be both and they are different.

Power Steering Pressure Line Hose Assembly for Toyota ...

eBay https://www.ebay.ca > ... > Power Steering Hoses
Power Steering Pressure Line Hose Assembly for Toyota Tundra 2007 2008 2009-2019 ; Quantity. 10 sold. More than 10 available ; Item Number. 285044205082 ; Brand.
$58.45 · ‎ In stock

More here including OEM

2009

https://www.google.com/search?q=2009+Toyota+tundra+Power+steering+high+pressure+line

2002

https://www.google.com/search?q=2002+Toyota+tundra+Power+steering+high+pressure+line.

..

Gates 352714 Power Steering Return Line Hose Assembly for 2007 Ford Expedition 5.4L V8 Gas SOHC.
I found this number, look online eBay or amazon or go to local parts store. Be sure to replacement power steering fluid that i compatible to your car..

Power Steering Pump - 4.0L Special Tool(s) Installer Set, Teflon® Seal
211-D027 (D90P-3517-A) or equivalent Material Item Specification MERCON® V Automatic Transmission Fluid
XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada) MERCON® V
Item Part Number Description 1 388898 Teflon® seal 2 - Pressure line-to-pump fitting (part of 3A719) 3 W700839 Power steering pump bolts (3 required) 4 3A674 Power steering pump 5 W503924 Pressure line bracket-to-engine bolt 6 3691 Power steering pump supply hose 7 W503924 Power steering pump supply hose bracket bolt
Removal
NOTICE: While repairing the power steering system, care should be taken to prevent the entry of foreign material or failure of the power steering components may result.

1. Using a suitable suction device, remove the power steering fluid from the reservoir.

1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02.

1. Remove the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.

1. Remove the pressure line bracket-to-engine bolt.

1. Remove the power steering pump supply hose bracket bolt.

1. Release the power steering pump supply hose clamp and disconnect the hose.

1. Disconnect the pressure line-to-pump fitting.
   • Remove and discard the Teflon® seal.

1. Remove the 3 bolts and the power steering pump.

Installation

1. NOTE:A new Teflon® seal must be installed.Using the Teflon® Seal Installer Set, install a new Teflon® seal to the pressure line fitting.

1. Position the power steering pump and install the 3 bolts.
   • Tighten to 25 Nm (18 lb-ft).

1. Connect the pressure line-to-pump fitting.
   • Tighten to 75 Nm (55 lb-ft).

1. Connect the power steering pump supply hose.

1. Install the power steering pump supply hose bracket bolt.
   • Tighten to 11 Nm (97 lb-in).

1. Install the pressure line bracket-to-engine bolt.
   • Tighten to 11 Nm (97 lb-in).

1. Install the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.

1. Fill the power steering system. For additional information, refer to Section 211-00.

Item Part Number Description 1 Fluid reservoir 2 Steering wheel 3 Steering column assembly 4 Flexible coupling 5 Tie-rod end 6 Tie-rod 7 Steering gear boot 8 Steering gear 9 Fluid cooler 10 Steering gear hoses 11 Power steering pump

Power Steering Line/Hose: Service and Repair
Pressure Hose
Power Steering Pressure Pipe/Hose Replacement (3.8L)
Removal Procedure
1. Place a drain pan under the vehicle.
2. Remove the accessory drive belt.
3. Raise and support the vehicle. Refer to Vehicle Lifting.
4. Remove the tire and wheel assembly.
5. The power steering pressure hose is the lower hose at the power steering gear.
Remove the power steering pressure hose from the power steering gear.
6. Remove the power steering pressure hose from the power steering pump.
7. Remove the power steering pressure hose from the clamps on the power steering gear.
8. Remove the power steering pressure hose from the vehicle.
Installation Procedure
1. Install the power steering pressure hose to the vehicle.
2. Install the power steering pressure hose to the clamps on the power steering gear.
Notice: Refer to Fastener Notice in Service Precautions.
3. Install the power steering pressure hose to the power steering pump.
^ Tighten the fitting to 27 Nm (20 ft. lbs.).
4. Install the power steering pressure hose to the power steering gear.
^ Tighten the pressure hose fitting to 27 Nm (20 ft. lbs.).
5. Install the tire and wheel assembly.
6. Remove the drain pan from under the vehicle.
7. Lower the vehicle.
8. Install the accessory drive belt.
9. Fill the power steering system with power steering fluid.
10. Bleed the power steering system.
11. Inspect the power steering system for leaks.

YOU CANT USE A REGULAR FUEL LINE ON POWER STEERING AS A HIGH PRESSURE HOSE.BECAUSE POWER STEERING PRESSURE IS 1000 PSI.YOU HAVE TO BUY THE POWER STEERING HIGH PRESSURE HOSE IT HAS NUMBER OF PLIES MATERIAL WEAVES TO MAKE IT STRONG.IT WAS MADE FOR POWER STEERING HIGH PRESSURE.YOU DONT HAVE A BLOCKAGE .THE HIGH PRESSURE HOSE JUST WORE OUT.REPLACE IT .IT SHOULD FIX THE PROBLEM.

Item Part Number Description 1 - Steering wheel 2 - Steering column 3 - Boot 4 - Tie-rod 5 - Tie-rod end 6 - Steering gear 7 - Steering gear to fluid cooler hose 8 - Fluid cooler 9 - Power steering pressure (PSP) switch 10 - Power steering pump 11 - Fluid supply hose 12 - Fluid reservoir 13 - Pump to steering gear pressure line 14 - Steering gear pinion extension

Section 11-02C: Steering Gear, Power Rack and Pinion, Explorer 1996 Explorer with Power Rack and Pinion Steering Workshop Manual REMOVAL AND INSTALLATION Steering Gear SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Pitman Arm Puller T64P-3590-F
Removal

1. Start engine.
   

1. Rotate steering wheel from lock-to-lock (entire gear travel). Record n umber of rotations.
   

1. Divide the number of rotations by two. This gives the required number of turns to place system in the on-center position.
   

1. NOTE: Verify the front wheels and steering wheel are in the straight-ahead position.
   
   From the lock position, rotate steering wheel the number of turns determined in Step 3. This places the gear in the on-center position.
   
   
   Steering Gear, Explorer
   
   
   
   
   

1. NOTE: Do not rotate steering column when intermediate shaft is disconnected or DAMAGE TO CLOCKSPRING will result.
   
   Remove bolt retaining the lower steering column shaft to the steering gear input shaft.
   
   
   
   
   

1. Disconnect the lower steering column shaft from the steering gear.
   

1. Remove stabilizer bar attachment from frame for clearance to remove gear.
   

1. Unscrew the quick connect fittings for the power steering pressure hose (3A719) and power steering return hoses (3A713) at the steering gear housing (3548).
   
   
   Power Steering Hose Connections
   
   
   
   
   
   Item Part Number Description 1 3A674 Power Steering Pump 2 3A719 Power Steering Pressure Hose 3 3F780 Power Steering Cooler and Hose Assembly 4 3504 Steering Gear 5 5005 Frame

1. Plug ends of fluid lines removed and ports in gear to prevent damage and entry of dirt.
   

1. Remove two (2) nuts from P/S cooler.
   

1. Remove P/S cooler from vehicle.
   

1. Remove and discard the cotter pin retaining the nut to tie rod end (3A130) and remove nut.
   

1. Separate tie rod ends from front wheel spindle (3105) using Pitman Arm Puller T64P-3590-F.
   
   
   
   
   

1. Remove the two nuts, bolts, and washer assemblies retaining steering gear (3504) to front crossmember (5019).
   

1. Remove steering gear from vehicle. If required, remove steering gear mounting bracket housing insulators (3F640) and steering gear insulators (3C716) from steering gear housing.
   
   
   
   
   
   Item Part Number Description 1 N807881-S60 Bolt 2 385935-S36 Washer 3 3F640 Steering Gear Mounting Housing Insulator 4 3504 Steering Gear 5 N800255-S60 Nut 6 5019 Front Crossmember 7 3C716 Steering Gear Insulator

Installation

1. If removed, install steering gear mounting insulators into the steering gear housing.
   

1. Push the steering gear mounting insulator and steering gear insulator in until there is no space between the lip on the insulator and steering gear housing.
   

1. Position steering gear on front crossmember. Install nuts, bolts and washers retaining steering gear to front crossmember. Tighten to 128-172 Nm (94-127 lb-ft).
   

1. Position power steering cooler onto bolts and install nuts. Tighten nuts to 68-92 Nm (50-68 lb-ft).
   

1. NOTE: The fittings design allows the power steering pressure hose and power steering return hose to swivel when properly tightened. Do not attempt to eliminate looseness by overtightening, since this can cause damage to fittings.
   
   Connect power steering pressure hose and power steering return hose to appropriate ports on steering gear housing. Tighten fittings to 27-34 Nm (20-25 lb-ft).
   

1. NOTE: Make sure the tie rod ends (3A131) are seated in the tapered spindle holes to prevent rotation while tightening nut.
   
   With the steering gear, steering wheel (3600) and wheel (1007) in the on-center position, attach the tie rod end to front wheel spindle and tighten to 56-76 Nm (77-103 lb-ft).
   

1. If necessary, advance tie rod nuts to the next slot. Install cotter pins.
   

1. NOTE: Verify that no rotation from the on-center position has occurred.
   
   Position steering column lower intermediate shaft over steering gear input shaft. Outer input shaft dust shield must be in place. Replace pinch bolt and tighten to 41-56 Nm (30-42 lb-ft).
   

1. Replace the front wheel and tire assemblies. Refer to Section 04-04 .
   

1. Replace wheel covers.
   

1. Lower vehicle.
   

1. Refill power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent meeting Ford specification ESW-M2C33-F.
   

1. Purge air from steering system. Refer to Section 11-00 . Verify absence of any unusual power steering noise.
   

1. Check and adjust toe alignment specifications. Refer to Section 04-00 .
   

1. Make sure steering gear operates correctly and is not leaking.
   

1. Check and adjust fluid level in power steering oil reservoir.
   

i pERSONALY WOULD REPLACE IT MYSELF EVEN WITHOUT MY 30yrs Of Experience in this Field. I have Enclosed Instructions for you to use. PLEASE dont Forget to RATE me As MOST folks DONT remember to that is how WE Get our Ratings such as GURU THANK YOU and Good Luck On The Job, Dont PAY a dime If YOU CAN > D I Y

REMOVAL PROCEDURE

1. Remove the power steering pressure hose (2) from the power steering pump (1).
2. Raise the vehicle on a hoist. Refer to Vehicle Lifting.
3. Remove the front exhaust pipe, automatic transmission only. Refer to Intermediate Pipe Replacement in Exhaust System
4. Remove the power steering pressure hose (1) from the power steering gear (3).
5. Remove the power steering hose retainer (2).
6. Remove the power steering pressure hose (1) from the vehicle
   1. Install the power steering pressure hose (1) to the vehicle
   2. Install the power steering hose retainers (2). NOTICE: Refer to Fastener Notice in Service Precautions.
   3. Install the power steering pressure hose (1) to the power steering gear (3). Tighten the fitting to 27 Nm (20 ft. lbs.).
   4. Install the front exhaust pipe, if removed. Refer to Intermediate Pipe Replacement in Exhaust System.
   5. Lower the vehicle.
      1. Install the power steering pressure hose (2) to the power steering pump (1). Tighten the fitting to 27 Nm (20 ft. lbs.).
      2. Bleed the power steering system. Refer to Bleeding Power Steering System in Service and Repair of Steering.

Here is a pic.

[IMG]http://i253.photobucket.com/albums/hh43/chuck943/DG1690A.gif[/IMG]



1 3A674 Power Steering Pump 2 3A714 Power Steering Pressure Hose 3 3C510 Power Steering Hose Bracket 4 3N824 Power Steering Pressure Switch 5 3504 Steering Gear 6 3A713 Power Steering Return Hose (Gear to Cooler) 7 3D746 Power Steering Fluid Cooler 8 3493 Power Steering Return Hose (Cooler to Pump