Need the torque specs for a 1994 350 cyl head the one with the 4 bolts through the center of the valve cover and is this the same spec for a vortec engine

In the link and a video as well. NOTE: they are POUND INCH not Foot Pounds.

Torque Pattern for Valve Cover? - Kia Forum

kia-forums.com https://www.kia-forums.com > threads > torque-patter...
Sep 17, 2013 - show the locations of the bolts on the "Cylinder Head Cover" --aka valve cover-- and they provide the torque at 35-52 lb-in (4-6Nm), but they ...

Valve Cover Gasket help
Apr 28, 2012
Torque specs and sequence for intake bolts
Jul 10, 2022
Need Bolt Pattern for Valve Cover, please help?
May 15, 2018
torque specs?
Mar 20, 2017
More results from www.kia-forums.com

..

2003 Cadillac CTS V6-3.2L VIN N - Justanswer

http://ww2.justanswer.com > uploads > joecamel90
PDF
Apr 16, 2010 - Tighten the cylinder head bolts to 25 Nm (18 ft. Tighten the cylinder head bolts to 90 degrees using the J 36660-A. Tighten the cylinder head ...
6 pages

What Is the Torque for the Heads - 2CarPros

https://www.2carpros.com > ... > Cylinder Head > Torque
Jun 29, 2010 - MEMBER; 2003 CADILLAC CTS; 6 CYL; 2WD; AUTOMATIC; 100,000 MILES. I am repairing the heads of this car. whats the torque I need to apply?

Complete Torque Specs List ' Cadillac CTS-V Forum

https://www.ctsvowners.com > threads > complete-torqu...
Jul 1, 2013 - Cylinder Head Core Hole Plug: 15 lb ft. Drive Belt Idler Pulley Bolt: 37 lb ft. Drive Belt Tensioner Bolts: 37 lb ft. Engine Block Coolant ...
Torque Specs??? - Cadillac CTS-V Forum
Apr 4, 2012
Torque Specifications ' Cadillac CTS-V Forum
Mar 8, 2012
Engine bolt torque specs, other - Cadillac CTS-V Forum
Nov 24, 2015
Factory head bolts reused ' Cadillac CTS-V Forum
Sept 11, 2014
More results from www.ctsvowners.com

Go on your computer in your browser and type in '1990 Honda Accord 2.2 4 cylinder head bolts torque specifications'. You will get back the engine bolt layout with the bolts numbered with the torque specs. You tighten the bolts according to the numbers of the bolts in the order starting with number 1 and working to the highest number.

Head and Cam Bolt Torque specs? - PT Cruiser Forum

www.ptcruiserlinks.com > ... > Tech & Performance Forum

Nov 5, 2012 - 2 posts - ‎2 authors
I am putting everything back on after replacing the head gasket. I was wondering what the Torque Specs and Sequences are for both the Head ... Torque Specs
10 posts
Jul 28, 2012
Valve cover torque specs
5 posts
Jul 4, 2011
Timing Repair Project - Bolt Torque Specs
7 posts
Jun 16, 2011
torque specs?
9 posts
Mar 20, 2006
More results from www.ptcruiserlinks.com

Dodge Stratus / Chrysler Pt Cruiser / Sebring Camshafts ...

? 5:07
https://www.youtube.com/watch?v=2wB2o27eWgo
Aug 20, 2015 - Uploaded by World Mechanics
Dodge Stratus / Chrysler Pt Cruiser / Sebring Camshafts Install and Torque Specs 2.4 Engine. ... 2004 Chrysler PT CruiserCamshaft Install

Dodge Stratus / Chrysler Sebring / Pt Cruiser 2.4 Head ...

? 6:08
https://www.youtube.com/watch?v=7rY7tDbye-8
Aug 16, 2015 - Uploaded by World Mechanics
... Stratus / Chrysler Sebring / Pt Cruiser 2.4 Head gasket Install and torque specs We took this video to ... 2004 Chrysler PtCruiser head gasket

its not very hard at all. once you get the heads off just make sure you follow the proper sequence to tighten the bolts. always remember to tighten from the center bolts out to the end bolts so the heads seat flat and even. and make sure you have the proper torque specs for those head bolts. 1) hand tighten. 2) torque to half of the OEM spec. 3) full torque spec. all of this takes a while to do so be patient.

I’m happy to help further over the phone at https://www.6ya.com/expert/christopher_64bc1c93be5190d5

main caps 85 ftlbs (3divdedsetings30ftlbs all 50 ftlbs all ending at85ftlbs click, rocaps 45ftlbs, head bolts 85ftlbs workingfrom cdenter top ,center botom ,top center working clock wizeand out ,intake boltes45ftlbs again fromcenter working outleft side, right side,left, right 8 bolts one time only or u will distort gasket. oilpan from center alternate L side ,R side,clock wize25ftlbsclick recheck after breakin period valve covers 25ftlbs anrecheck flywheel 90ftlbs ,harmnic balancer bolt 75ftlbs, add oil!!!!run for 15 minutes drain oil &change filter run for 100miles for molly rings 10 mmiles for cast rings .let engine cool down retorque headbolts,replace valve covers .run it and get on it!!! good luck hve fun.

Torque spec

Step 1- 44 Ft.Lbs.
Step 2- 59 Ft.Lbs.
Step 3- Tighten bolts an additional 90 degrees.

Here the head bolt's tightening sequence.

Hello there
Torque Specs
These specs may not be correct for your application.
Verify your engine specs with a service manual for your year and model.
always torque bolts in three equal increments
Bolts or Parts Lube or Sealer Torque to: 7/16 Main Caps (2 bolt) Engine Oil 70 ft-lbs. 7/16 Inner Main Caps (4 bolt) Engine Oil 70 ft-lbs. 7/16 Outer Main Caps (4 bolt) Engine Oil 65 ft-lbs. 3/8 Outer Main Caps (4 bolt) Engine Oil 40 ft-lbs. Warning!!! If you are using ARP bolts, you MUST use
their specs. Click Here! 3/8 Connecting Rod Bolt Engine Oil 45 ft-lbs. 11/32 Connecting Rod Bolt Engine Oil 45 ft-lbs. Cylinder Heads
Engine oil
(blind hole)
Sealer
(water jacket)
65 ft-lbs.
Rocker Studs (screw-in) Engine Oil 50 ft-lbs. Oil Pump Engine Oil 65 ft-lbs. Oil Pan Engine Oil 12 ft-lbs. Cam Sprocket (upper gear) Thread Locker 20 ft-lbs. Timing Cover Engine Oil 6 ft-lbs. Intake Manifold
(Cast Iron Heads)
Non- Hardening Sealer 30 ft-lbs. Valve Cover Engine Oil 3 ft-lbs. Exhaust Manifold Anti-Seize Lubricant 25 ft-lbs. Spark Plugs No Lube or Sealer 20 ft-lbs. Flexplate (Automatic)
Flywheel (Clutch)
Thread Locker 60 ft-lbs. Clutch Pressure Plate Thread Locker 35 ft-lbs. Centerbolt
(Harmonic Damper)
Engine Oil 60 ft-lbs. Bellhousing
(Transmission to Block)
Engine Oil 25 ft-lbs. Head Bolt Tightening Sequence

The haynes book is not recommended since there are numerous mistakes and they still will not update. One of the biggest is the firing order.

The factory service manual is the only way to go.

Head bolts - 46 - 50.5 lbs (there is an order sequence for the bolts)

Intake & exhuast manifolds- 13.5 - 20 lbs

Flywheel - 41.5 - 47 lbs

Clutch cover - 13.5 - 20 lbs

Vortecs are a little different that old school small blocks, grab a Haynes or Chiltons, the cross patterns and specs are simply diagramed. Vortec, as any really, start with 25# then 45# and then final torque which I believe is around 70-75# but to be sure verify with the manual. AutoZones, Murry's, Adavance auto all carry the books, Cheap insurance.
Dan