Location of mazda premacy 02 petrol fuel filter

Anand Kumar

• 2035 Answers
• Posted on Oct 17, 2008

SOURCE: changing fuel filter on 2002 Mazda pickup

Clean all dirt and/or grease from the fuel filter fittings. "Quick Connect" fittings are used on models equipped with a pressurized fuel system. These fittings must be disconnected using the proper procedure or the fittings may be damaged. The fuel filter uses a "hairpin" clip retainer. Spread the two hairpin clip legs about 1/8 in. (3mm) each to disengage it from the fitting, then pull the clip outward. Use finger pressure only; do not use any tools. Push the quick connect fittings onto the filter ends. Mazda recommends that the retaining clips be replaced whenever removed. The fuel tubes used on these fuel systems are manufactured in 5/16 in. and 3/8 in. diameters. Each fuel tube takes a different size hairpin clip, so keep this in mind when purchasing new clips. A click will be heard when the hairpin clip snaps into its proper position. Pull on the lines with moderate pressure to ensure proper connection. Start the engine and check for fuel leaks. If the inertia switch (reset switch) was disconnected to relieve the fuel system pressure, cycle the ignition switch from the OFF to ON position several times to re-charge the fuel system before attempting to start the engine.
Remove the "hairpin" clip retainers to access the fuel line fittingsThe inline reservoir type fuel filter should last the life of the vehicle under normal driving conditions. If the filter does need to be replaced, proceed as follows:
CAUTIONIf the fuel filter is being serviced with the rear of the vehicle higher than the front, or if the tank is pressurized, fuel leakage or siphoning from the tank fuel lines could occur. to prevent this condition, maintain the vehicle front end at or above the level of the rear of vehicle. also, relieve tank pressure by loosening the fuel fill cap. cap should be tightened after pressure is relieved.

1. Shut the engine off. Depressurize the fuel system.
2. Raise and support the vehicle safely.
3. Detach the fuel lines from both ends of the fuel filter by disengaging both push connect fittings. Install new retainer clips in each push connect fitting.
4. Note which way the flow direction arrow points on the old filter.
5. Remove the filter from the bracket by loosening the filter retaining clamp enough to allow the filter to pass through.

1. Install the filter in the bracket, ensuring proper direction of flow as noted by arrow. Tighten clamp to 15-25 inch lbs.
2. Install the push connect fittings at both ends of the filter.
3. Lower the vehicle.
4. Start the engine and check for leaks.

1. Before servicing the vehicle, refer to the Precautions section.
2. Properly relieve the fuel system pressure.
3. Remove or disconnect the following:
   • Negative battery cable
   • Push connect and R-clip fittings from the fuel filter
   • Fuel filter Fuel filter location and connections–2002–2006

1. Install or connect the following:
   • Fuel filter. Torque the nut to 17 ft. lbs. (23 Nm).
   • R-clip and push connect fittings
   • Negative battery cable
2. Start the vehicle, check for leaks and repair if necessary.

SOURCE: Fuel Filter location on a Petrol 2004 Kia Carnival

The fuel filter is located in the fuel tank, pump removal is required to replace. There is an inspection cover behind the front seats on the floor to gain access to the pump. stupid idea. but whats not stupid about kia.

SOURCE: where is the fuel filter

in the gas tank, Not an easy fix I had it done.  about 3-4 hundred

SOURCE: how do i replace the fuel pump in my 1993 mazda 626 2.5

1. Relieve the fuel pressure and disconnect the negative battery cable.

2. If not already removed, depress the clips on each end of the rear seat cushion and remove the cushion.

3. If not already done, detach the electrical connector from the fuel pump/sending unit.

4. Remove the attaching screws from the fuel pump/sending unit access cover and remove the cover.

5. Disconnect the fuel supply and return hoses from the fuel pump/sending unit.

6. Remove the attaching screws and the fuel pump/sending unit from the fuel tank.

7. Detach the sending unit electrical connector, remove the sending unit attaching nuts and remove the sending unit from the fuel pump assembly.



To install:

1. Attach the sending unit to the fuel pump assembly and install the nuts. attach the sending unit electrical connector.

2. Install the fuel pump/sending unit into the fuel tank with a new gasket and install the mounting screws.

3. Connect the fuel supply and return lines.

4. Install the access cover and the mounting screws.

5. Attach the sending unit electrical connector.

6. Position the rear seat cushion over the floor, making sure to align the retaining pins with the clips. Push down firmly until the two retaining pins are locked into the rear seat retaining clips.

7. Connect the negative battery cable, start the engine and check for proper system operation and for fuel leaks.

SOURCE: 2000 mazda 626 fuel filter location.engine

it should be on the driver side. very hard to get to. look under the air box were the air filter goes.
j.aguilar