Rear hub nut torque setting Hyundai coupe 2000 se

Call Kia with your VIN to make sure yours wasn't affected by the recall. You may be able to have that rear bearing replaced for free at Kia.

HUBCAP & OUTER BEARING REPLACEMENT PROCEDURE: 1. Remove the two (2) cross-tip locating screws on the brake drum.

2. Remove the brake drum.

3. Remove cotter pin and cover set.

4. Remove nut, claw washer, outer bearing and hub assembly.

5. Inspect inner bearing area in both hubs for any sign of moisture, corrosion, grease discoloration or contamination. If "yes" discard entire hub and replace with new assembly. If "no" proceed with outer bearing replacement below: 6. Carefully remove the outer bearing race from the hub. If the hub assembly is damaged then replace the hub assembly as a complete unit. (If inner seal is damaged while removing the outer race replace with new seal.)

7. Clean all contaminated grease from outer bearing cavity of the hub.

8. Install a new outer race into the hub using an appropriate race installation tool.

9. Apply grease MS511-33 WBG2 or equivalent to the hub assembly and the new bearing(s) especially to the shaded areas.

10. Install hub assembly, new pre-greased outer bearing and new claw washer on spindle. (Or alternatively, install entire new hub assembly, as supplied). Ensure bearings are properly seated then tighten hub/spindle nut, torque nut to 20-25 lb-ft (27-33 Nm.) Verify hub spins freely without signs of binding or excessive play.

11. Install new cover set and cotter pin; never reuse the old cotter pin.

12. Install new hub cap with Loctite # 5910(TM) or equivalent sealant to prevent moisture intrusion.

13. Install the rear brake drum using tapered locating screws.

14. Install rear wheels and torque lug nuts to proper specification. (65-79 lb-ft) (88-108 Nm, 9-11 kgm)

15. Lower vehicle.

2000 Ford Focus Drum Removal ProcedureIf removing the drum to service the rear brakes: (note, do not remove hub retaining nut for this procedure)
1. Raise and support vehicle
2. Release the parking brake
3. Remove wheel and tire
4. Disconnect wheel speed sensor wiring harness from wheel knuckle and floor panel.
5. Remove 4 wheel spindle attaching bolts, then the wheel hub and drum assembly from vehicle.
6. Reverse procedure to install noting the following:
a. Torque wheel spindle retaining nut to 49 ft. lbs.
b. Torque wheel/tire assembly to 94 ft. lbs.
2000 Ford Focus Drum Replacement ProcedureIf replacing the drum and wheel bearing assembly:
1. Raise and support vehicle
2. Release the parking brake
3. Remove wheel and tire
4. Remove center dust cap.
5. Remove hub retaining nut.
6. Remove drum and hub assembly. Ensure wheel speed sensor ring is not damaged when removing drum/hub (if equipped).
7. Reverse procedure to install noting the following:
a. Inspect and clean wheel speed sensor ring if equipped.
b. When tightening hub retaining nut, rotate the hub assembly in counterclockwise direction.
c. Torque hub retaining nut to 173 ft. lbs.
d. Torque wheel/tire assembly to 94 ft. lbs.
e. Adjust parking brakes as necessary.

The drum and hub are one assembly on that vehicle so you will need to remove the dust cap in the center of the drum and remove the large axle nut. The drum/hub/bearing assembly will then pull off of the spindle.

If you want to replace the drum you will either have to find one with a bearing already installed, Have your old bearing pressed out of the old drum and pressed into the new drum, or have new bearings pressed into the new drum.

When installing the new drum it is very important to tighten the axle nut to the proper spec. I can get that spec for you if you need it.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

4-Wheel Drive

1. Before servicing the vehicle, refer to the Precautions Section.
   
2. Remove or disconnect the following:
   
   • Negative battery cable
     
   • Rear wheel
     
   • Rear brake shoes
     
   • Rear halfshaft nut and loosen the halfshaft from the hub
     
   • Wheel hub and place it in a vise
     
   • Inner wheel bearing race from the hub
     
   • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
     
   • Parking brake cable from the steering knuckle
     
   • Brake line from the wheel cylinder and support the knuckle
     
   • Lower shock absorber nut
     
   • Lower ball joint by holding the ball joint stud
     
   • Upper ball joint
     
   • Coil spring while noting the location of the insulator
     
   • Steering knuckle cam
     
   • Steering knuckle
     
   • Snapring and press out the outer wheel bearing race from the knuckle
     

     Rear hub and bearing
     Click to Enlarge

To install:

1. Install or connect the following:
   
   • New wheel bearing into the steering knuckle
     
   • Snapring to the knuckle
     
   • Wheel hub
     
   • Steering knuckle cam and hand tighten the bolt
     
   • Coil spring
     
   • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
     
   • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
     
   • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
     
   • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
     
   • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
     
   • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
     
   • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
     
   • Brake shoes
     
   • Rear wheel
     
   • Negative battery cable
     
2. Fill and bleed the brake system.
   
3. Check and adjust the wheel alignment as needed.
   

2-Wheel Drive

1. Before servicing the vehicle, refer to the Precautions Section.
   
2. Remove or disconnect the following:
   
   • Negative battery cable
     
   • Rear wheel
     
   • Rear brake drum
     
   • Wheel hub nut
     
   • Wheel hub
     
   • Inner wheel bearing race from the hub
     
   • Snapring
     
   • Wheel bearing outer race from the knuckle
     

     Rear hub and bearing
     Click to Enlarge

     Rear hub removal
     

     Inner wheel bearing removal-rear hub/bearing
     

     Rear wheel bearing removal-2wd
     

     Rear wheel bearing removal-4wd
     

To install:
Install or connect the following:

• Wheel bearing in to the knuckle
  
• Snapring
  
• Wheel hub into the wheel bearing
  
• Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  
• Brake drum
  
• Rear wheel
  
• Negative battery cable
  

  Rear wheel bearing installation
  
  hope this helps if so send testimonial comment or even any other questions you have
  

REMOVAL & INSTALLATION Except Miata FRONT

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Remove or disconnect the following:
   • Steering knuckle from the vehicle
   • Inner oil seal from the knuckle
3. Using Mazda Hub Puller tools 49 G033 102, 49 G033 104 and 49 G033 105, pull the front wheel hub from the knuckle assembly.
4. Remove or disconnect the following:
   • Bearing inner race from the front wheel hub
   • Retaining ring from within the knuckle
   • Front wheel bearing from the knuckle, using the hub puller tools
   • Brake dust shield
5. Clean and inspect all parts but do not wash or clean the wheel bearing. The bearing must be replaced. To install:
   
6. Using Mazda Press tools 49 G033 107 and 49 H026 103, install a new dust shield cover assembly to the knuckle.
7. Using the press tools, press a new wheel bearing into the knuckle assembly.
8. Install or connect the following:
   • Wheel bearing retaining ring
   • New oil seal using Installation tool 49 V001 795
   • Front wheel hub using the Mazda press tools

REAR

1. Before servicing the vehicle, refer to the precautions in the beginning of this section. NOTE: The wheel bearings are not serviceable. If the bearings are bad, a new hub/bearing assembly must be installed.
   
2. Remove or disconnect the following:
   • Rear wheels Fig. 1: Exploded view of the rear wheel hub and bearing assembly (disc brake model shown, drum is similar)
     
     
   • Brake drum, if equipped
   • Rear caliper and rotor assembly from the hub, if equipped
   • Hub dust cover
3. Raise the staked portion of the hub retaining nut with a hammer and chisel.
4. Remove or disconnect the following:
   • Hub retaining nut and discard it
   • Hub and bearing assembly from the spindle Fig. 2: When installing the new hub nut, be sure to stake it into the notch on the spindle
     
   To install:
   
5. Install or connect the following:
   • Bearing assembly on the spindle. Torque the new nut to 131-173 ft. lbs. (177-235 Nm)
   • Stake the nut into the groove in the spindle
   • Dust cover
   • Assemble the brakes
   • Rear wheel

Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical)

1. Release parking brake.
2. Remove rear wheel assembly.
3. Remove rear wheel speed sensor from carrier.
4. Dismount brake caliper and support with mechanic's wire.
5. Remove brake disc.
6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical)
   
   
7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
8. Remove carrier.
9. Remove stakes and remove flange nut.
10. Support bearing outer race flange and press rear axle hub out.
11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.

To Install:
Hub bearing assembly (Typical)

1. Apply thin coat of grease to bearing contact surface and hub.
2. Using and appropriate tool, press bearing into hub. CAUTION
   Do not press against outer race of wheel bearing.
   
3. Install flange nut and stake nut until it meets concave portion of spindle.
4. Install carrier.
5. Use an appropriate tool to press tone wheel.
6. Install hub/bearing assembly with rounded portion of outer race facing up.
7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
8. Measure wheel bearing starting torque with a spring balance or equivalent device.
   • Starting torque should measure 15.9 in lb (1.8 Nm) or less
9. Install brake disc.
10. Mount brake caliper.
11. Install rear wheel speed sensor to carrier.
12. Install rear wheel assembly.

2WD pickups don't have hubs. They have rotors with bearings. Once you have the brake assembly supported, remove nut from spindle. Be sure not to strip the threads on the spindle. Remove the front set of bearings and pull the rotor off. Remove the rear set of bearings. Be sure to pack greases into new bearings prior to installation. Insert new rear bearing into rotor and replace onto spindle. Insert new front bearing and washer and re-install nut. Tighten to recommended torque specs, grease fittings and replace brake assembly.

The rear hub and bearing are combined into a single assembly. The bearing is sealed for life and requires no lubrication or attention. If the bearing is worn or damaged, you have to replace the entire hub and bearing assembly:
loosen the rear wheel lug nuts, raise the vehicle, place it on jack stands and remove the rear wheel.
Remove the brake drum or caliper and disc.
Remove the dust cover (in the center).
Unstake the hub retaining nut (bend the part out that locks it), unscrew the nut and remove the thrust washer then remove the hub assembly.
Install the new assembly and thrust washer, tighten the new nut to torque 134 lbs, then stake in the edge of the nut (opposite of unstaking).
Tap the dust cover into place, all around the edge until it's seated.
Reverse removal for the rest.
Hope this helps you understand the process.

drum brakes you remove rear wheel- speed sensor-grease cap-flange nut-outer bearing-brake drum-inner grease seal-inner bearing-drive the bearing races out of the drum hub.to install -install the inner and outer bearing races.apply grease to the bearings and hub cavity.then you install the inner bearing -inner grease seal-brake drum-outer bearing-flange nut torque it to 159 to 192 ft lbs. THE REAR DISC BRAKE WHEEL BEARINGS-you have to remove rear wheel -wheel speed sensor-brake caliper and rotor-rear axle hub bolts-tone the wheel with tool 09445-21000-carrier assembly-nut after unstaking it-press out the rear axle hub-remove the bearing inner race with tool 09445-21000-remove the bushings from the carrier with tools 09453-33000b and 09545-21100.to install -press in the bushings to the carrier with tools 09453-33000b and 09545-21100- press in the bearings to the hub with tool 09221-21000.tighten the flange nut to meet the concave portion of the spindle-press in the tone wheel with tool 09221-21000-torque the nut to 191 ft lbs -install the hub and bearing assembly to the backing plate and torque the bolts to 88 ft lbs-install the brake caliper and rotor.install the wheel speed sensor if equipped.install the rear wheel.TO BUY THE TOOLS TO DO THE JOB.LOOK UP KENT MOORE TOOLS ON INTERNET.

What year miata?