Timing mark location on a rodeo c22ne engine - 2002 Isuzu Rodeo

I guess you didnt follow the fuel line.?
what engine is there, Isuzu ran carbs last, until 1994
the fuel tank and all fuel lines match the engine.
some are gas others are diesel.
in what country, they sold them world wide and are not the same.
the line up is.
gen3 alone.
2.2 L 115 hp (85 kW) C22NE / 22LE I4
2.3 L 4ZD1 I4 (carb)
2.6 L 4ZE1 I4
2.5 L 4JA1-T
2.8 L 4JB1-T td I4
3.0 L 4JH1-T
3.1 L 4JG2-T td I4
3.1 L LG6 V6
3.2 L 6VD1 V6

on the USA car,
the book says, and I quote
"

The Pick-up (P'UP), Amigo and Rodeo models are equipped with the fuel filter located directly in front of the fuel tank, whereas on the Trooper/Trooper II models, the fuel filter is located along the inner side of the right frame rail, near the rear of the vehicle."

maybe yours is missing if not there....
next time post country and engine
gas/diese
and displacement."size" and cyl count

what car, you forgot its name? ISUZU what?
the books are first indexed by MFG,Name and year,
then by engine options, so I cant look it up for you can I.
of what the whole engine
if car is uSA car, on this USA forum say so?
then go to mitchells and login and read all that.
as most mech,do...
or if 15bucks is scary

search. always free.

https://duckduckgo.com/?q=isuzu+C22NE+torque&ia=web

Just the engine. The marks on the belt are to make sure the teeth are in the right place when replacing. It might come back in place on 4 turns of the crankshaft. I have never checked to see if the belt marks came back. But always check the timing marks themselves.

Hope this helps.

• I hope you get this, I was going to go to bed until I noticed how bad you were needing some timing marks :)

• Injection pump and camshaft alignment marks-diesel engine

• Tensioner pulley bolt sequence (diesel)

• Crankshaft sprocket timing mark-2.3L and 2.6L engine

• Camshaft sprocket timing mark-2.3L and 2.6L engine

• Timing belt installation sequence-2.3L and 2.6L engines

• Timing belt tensioner lockbolt-2.3L and 2.6L engines

• If you have any comments please feel free to leave them here.
• Hope this helps and thank you for using FixYa.

Regards, Tony

Hello phillip65g,

Below are images depicting the location and orientation of the timing marks.

I hope this help.





Regards,

netvan

hi i had this problem my self not all of 2 weeks ago rebuilding a holden rodeo c22ne motor had bad miss new plugs will do you no good on this one
in my case the side of the piston had cracked the three ring holes right threw leaving only the oil ring intact in this case if you have replaced coil and spark plugs and all sensors its almost betting to be a busted piston do a compression test to see your pistons should be around 190 psi if number one is down a long way ie in my case 50 psi its about $250 to fix your self and you have to buy all pistons no use buying one only

The timing marks are stamped into the head and in the cam pulley, also on the crank and the case, find them and paint them white so you can see them, the new belts have the marks on the belt, they will line up, If they don't , you got it wrong, You can do this without spinning the cams or crank and losing the marks, as long as the belt marks line up, you will be all set. Put the pin in the tensioner before removing the belt. Did you change the water pump? And I think the engine is 3.2L. Get it in there and pull the pin, It should be right on. Turn over the engine by hand a couple times to make sure it comes around on the marks. If it is wrong, it will go about 11 or 12 miles, and you will need a new engine. Hope this helps.

there should be a dot on either cam shaft and a marking on the belt that line up. http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?chapterTitle=Engine+Mechanical+Components&partName=Engine+Mechanical&pageId=0900c1528002abcd&subChapterTitle=Timing+Belt+Cover%2C+Belt+%26amp%3B+Sprockets&partId=0900c1528002ab6d
hope that helps. one of the easiest cars I've ever timed

I do believe it is built into the ecm

The marks should be in the shape of "arrows" or indented "lines" located on the pulleys and the face of the head gasket. There are alike marks on the crankshaft pulley and the face of the engine block also. Make sure your #1 cylinder is at "Top Dead Center" before you line up the pulleys on the cylinder head and install the belt.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/david_62314e5b2470e8b5