Windshield washer not pumping but switched pump and still not working is it electrical

Spencer - the washer fluid pump is fed off the same fuse as the windshield wiper, i.e., #22 which is a 30 amp fuse. If the wipers work, the fuse is fine...could be another issue

What is the problem you are facing? Are you not getting any fluid spray from the nozzle? Could be a clogged hose, broken washer fluid pump or switch...

I recommend taking these steps, as I saw from another F150 site:
Open hood
** Locate washer fluid bottle
** Find the rubber hose near the bottom coming off of it
** Follow hose up to near firewall and find a connector
** Take hose off connector and point away from yourself
** Have someone power on the truck
** Press spray button
** If fluid then pump is working problem is after the connector near the sprayers
** If no Fluid then either the Pump is bad or the switch is bad.

There is a electric motor that pumps washer fluid . Located in the bottom of the washer fluid tank .
Wash Operation (Front and Rear Wipers)
The front and rear washer systems use the same windshield washer fluid pump. When either the front or rear wiper is in the washer position voltage will be supplied to one side of the windshield washer fluid pump (depending on whether it is front or rear), while the other side of the pump is grounded.
At this point, the windshield washer fluid pump sprays solvent onto the windshield. When the front or rear washer is activated, the BCM receives an input from the switch that is activated. The BCM will control the wipers while in the WASH mode. The BCM will control either the front wiper relay or the rear wiper relay to turn on the wipers. The windshield wipers operate at low speed for 3 swipes and returns to the park position.

When turning on the washers do you hear the motor run ? Have some one try it while you listen at the washer fluid tank ! These pump motors do go bad .
turn OFF the ignition.
Disconnect the harness electrical connector of the windshield washer fluid pump.
Connect a test lamp from the windshield washer pump control circuit to a good ground .
Turn ON the ignition, with the engine OFF.
Press the front washer switch.
Does the test lamp illuminate?
YES or NO !

Does the pump motor run when turn windshield spray?
Might be home in line.
Might be wrong fluid(too thick)
Might be wiper fluid motor broken.

1. check your windshield washer fluid level.
2. make sure you can hear the fluid pump operating when you operate the switch.
3. If you can hear the pump working and you have fluid in the reservoir but still no spray,
   
4. check the washer fluid lines don't have holes and aren't clogged or pinched. check the sprayer nozzles make sure they are not clogged with debris.
5. if your washer still doesn't work your fluid pump is probably the problem.
   

If the pump works, something should be flowing thru the hose to the spray nozzles.
And if the pump works, everything electrical is working.
How do you know the pump works ?

no the front is not in power with rear they are seperate. check wire plug (connector) at pump,( i assume pump is mounted on or in reservoir ) with test light for power while a helper depresses the spray switch. check for a blown fuse, check switch, check wiring

The easiest way to go about this would be to pull the electrical pigtail off of the pump itself and that will stop all pumping of the windshield fluid.Locate your windshield washer reservoir and look around the outside of it.There will be a conical looking pump with an electrical pigtail and a rubber hose connected to it.The hose is where the fluid is transferred, but the electrical pigtail is what you want to disconnect.There is a lock clip you have to release, then you can pull the pigtail off with ease.No more pumping!!!! I hope I could help!!! Get back to me with any more questions and thanks!! Rate me accordingly.

Most likely a bad washer fluid pump.

the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal

1. Disconnect the battery ground cable (14301).
   
2. Raise and support the vehicle.
   
3. Remove the RH wheel (1007).
   
4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
   
5. Remove the windshield washer reservoir top bolt.
   
   
6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
   
7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
   
8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
   
9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
   
10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.
    
    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.
    
    
11. Loosen the two windshield washer reservoir side bolts.
    
12. Remove the windshield washer reservoir by sliding it out of the side slots.
    
13. Remove the windshield washer pump.
    
    Installation

To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).

there is another small relay box just below the windshield washer reservoir about 11/2" wide x about 4" long the washer pump relay is in there