Question about 1999 Lexus LX470

1 Answer

How to charge a battery on a Lexus lx 470

I have an Everstart battery charger - do I put both the cables on the battery? Or positive on the battery and negative on a metal part of the car?

Posted by Robbin Nalley on

Ad

1 Answer

webslinger32

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 85 Answers

Put both cables on the battery

Posted on Oct 04, 2012

Ad

5 Related Answers

Anonymous

SOURCE: Thinking of buying

I too own a (2006) Lexus IS 250, and I would highly recommend the car. Best car purchase I've ever made. The IS 250 has been absolutely flawless, and everything works as well as the day I bought it almost 2 years ago.

Posted on Jul 08, 2008

Ad
alicantecoli

Colin Stickland

  • 22485 Answers

SOURCE: 2000 Lexus LX 470 won't start

put battery on charge for a at least a day if not two before you start interfering with with anything.Sounds like a flat battery or battery not holding enough reserve amperage power.

Posted on Jan 01, 2009

blueextc3221

blueextc3221

  • 15935 Answers

SOURCE: How to Replace the AC filter on my Lexus 01 LX 470

Perform steps 1-3 first to inspect whether you have the access doors or not before ordering filters!!!

Did this little project this evening. Figured I'd write it up.

5 Easy steps:

1. Remove glove box door by removing both screws at the bottom of the door.

2. First pop the the little flap with a fuse/relay out of the black plastic shield in the upper portion of the glove box opening. Next push it back behind the shield through the opening. Next remove the 3 screws holding the shield in place. Don't pull this shield out yet!! Read step 3 first.

3. Gently pull the shield out. Be careful because the glove box light is still plugged into this part. It is located on the right side of the shield. Once it is pulled out slightly, unplug the bulb from the harness and now you can fully remove the part.

4. Now you can see the vertical cover where the air filters reside. The cover is about 5 inches tall and about 1 inch wide. It has 2 tabs on the upper portion of the cover. Squeeze these tabs towards each other and pull the cover off.

5. The filters are now exposed. They are stacked on top of each other. Pull the first filter out then lift the next filter up and pull out. Put new filters back in and reverse the procedure.


Parts needed:
2 Cabin air filters (Toyota PN 88568-60010 if you drop CDan a pm)
1 Phillips screw driver

Time needed:
No more than 15 minutes

STEP BY STEP PHOTO INSTRUCTIONS

5308136.jpg
ce42e62.jpg
75dfbf5.jpg
4d6181d.jpg
c7d7ec9.jpg

Thanks for using FixYa - a FixYa rating is appreciated for taking the time to answer your FERE question.

Posted on Mar 19, 2009

super_guy

  • 1986 Answers

SOURCE: Removing rear tail light in Lexus lx 470

Open the tailgate and then you must unsnap the carpeted part. It's easier with two people as the plastic part that says "Lexus" has to be pulled up out of the way as it will spring back in place if someone is not holding it. Don't be afraid to pull on the carpeted part; it will snap back with ease. When it's off you will see where the lights are. There are three screws you must undo so you can take off the metal cover. Should be pretty easy from there!

Posted on Sep 11, 2009

Anonymous

  • 81 Answers

SOURCE: How to adjust Lexus LX 470 parking brake to hold

Pull the wheels off the back of the car. remove the rubber plug on the rotor hub and rotate the rotor to where the hole is on the bottom and look in there. you should be able to see a sprocket. take a long flathead screwdriver and move it up or down until the rotor does not freely move. then turn it two times in the opposite direction. do this for both sides then you should be good to go! good luck!

Posted on Nov 14, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where do I put jumper cables


it looks like you have one on the positive of the battery which is correct, then other needs to go to the negative on the battery or an unpainted part of the engine or frame on the vehicle. obviously, the other ends of the cables go to the jumper battery's corresponding, positive and negative terminals.

Sep 28, 2016 | Cars & Trucks

1 Answer

Trying to charge battery for first time. It says connect two red connectors. Do you charge it first then connect the connector afterwards?


1. I assume this is a car battery so the first thing you do is to disconnect the vehicle cables from the battery terminals. The negative first and then the positive. The positive terminal is marked with a plus sign ...+ ... When refitting the cables to the
battery after it is charged you fit the positive cable to the positive battery terminal(+) first and fit the negative(-) last.

2. Now that the battery is unconnected from the vehicle you can fit the charging cables to the battery terminals. The charger you have should have 2 cables leading from it , a positive with a red plastic insulation on the clip and a negative cable probably with black insulation on the clip.The instructions with the charger will tell you in which order the cables are to be attached to the battery and the order you remove them. Each of the 2 cables has to be clipped onto the correct battery terminal. The positive cable(+) from the charger goes to the positive battery terminal (+)and the negative cable(-) from the charger goes to the negative battery terminal(-).

3. Once the cables from the charger are properly connected to the battery, you can plug in the charger and turn on the power.

4. Batteries generate explosive gasses when being charged and it only takes one small spark to ignite them. Don't reconnect the battery after charging for a half hour or so and make sure the area where you are charging is well ventilated.

Dec 18, 2015 | Cars & Trucks

1 Answer

Locating starter on Lexus LX 470


The starter is located under the intake manifold in between the twu cylinder heads, the entire intake system has to be removed to replace the starter.

Mar 10, 2014 | 2002 Lexus LX 470

1 Answer

How to change battery in 2008 dodge avenger


Disconnect negative battery cable first then positive then remove battery hold down screws and install in reverse. Use rubber gloves to prevent battery acid with skin contact. I prefer using rubber pliers on negative battery cable. I feel its safer. When putting negative battery cable on, place on holding rubber part not the metal contacts.

Nov 24, 2013 | 2008 Dodge Avenger

1 Answer

Where is the negative post located? I need to attach a battery charger.


+ symbol is positive and - symbol is negative.. It should be the ( Black ) color cable on battery ..( Red )cable is positive + it shoul be stamped on the battery top or on side near terminals

Apr 27, 2013 | 2006 Cadillac DTS

2 Answers

Can i clean my battery conector


My advice to do it easy. Just find a battery booster which is already charged. Loose the bolt on the one terminal. You have to do it one after the other. So connect if you start with positive terminal put the clip (crocodile jaw ) on the positive wiring terminal and the other on the negative,so in this way you have continuous power.Remove the positive wire,clean the terminal on the battery and always be careful not to touch on any metallic surface,or by accident loose the connection.You tight the positive terminal and proceed the same way for the negative terminal.On doing so surely you will not loose and contact or power .

Jan 02, 2013 | 1999 Acura 3.5RL

2 Answers

My Everstart Maxx Jump Starter 500 amp will not charge and it beeps every 5 seconds unless I pull out the fuse? What is the problem?


I don't think they read the problem right. His charger will not hold a charge, not the car. I'm having the same problem. My charge will not charge when I plug it up to a outlet.

Dec 02, 2012 | Cars & Trucks

2 Answers

The manual for my '07 M6 says to charge the battery using the posts under the hood. I have located the "+" post but it doesn't look like what I am use to seeing. Where should I connect the...


On the newer model cars they have started putting the battery under a myriad of plastic covers to make the engine compartment look cleaner. The "+" post that you have found is directly connect to the positive terminal on the battery. Put the positive cable on that post and then the negative on a bare bolt that is connected to the frame of the car, I would use the one on the sway bar if possible.

Mar 14, 2011 | BMW M6 Cars & Trucks

2 Answers

Lexus 470 1999


What is the inquiry / problem

Dec 10, 2010 | 2001 Lexus LX 470

1 Answer

I have a new battery in the car but the car will not start. But whn I jump the car it starts. Why is it not starting on it's own?


1. Remove the battery wires and thoroughly clean all connections with a wire brush, that may take care of the problem.
2. If it doesn't, check to see if the charging system is good. You will need a digital voltmeter for this. To check the charging system, place one lead on the positive terminal, and another on the negative, with the engine running and lights off. You should get at least 14 volts. (You may need to have a helper accelerate slightly to get the 14 volts.) If not, the charging system is bad. Take the alternator off, and have the auto parts store test it before buying a new one.

Nov 02, 2010 | 2001 Lexus LX 470

Not finding what you are looking for?
1999 Lexus LX470 Logo

Related Topics:

301 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Mike

Level 3 Expert

4372 Answers

Brad Brown

Level 3 Expert

18596 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...