Rear window on nissan titan will not go down from front switch

Did the switch work before replaced battery ? 2008 CTS ? Cadillac ? These switches are inputs to a control module , DDM - driver door module . a computer of sorts . A lot of thing's can go wrong with these systems , broken power or ground circuits inside the rubber boot from the body to the driver door . Communication problems between control modules etc... Plus the power windows don't use fuse's , has a circuit breaker for front windows - PWR/WNDW circuit breaker 25 amp located in the fuse box under the back seat , Fuse's are used for rear windows - two 15 amp fuse's LT/REAR an rear ,both are in the rear fuse box under back seat. These rear windows are controlled by the BCM - body control module .

The power windows system consists of the following components:
• Driver door module (DDM)--GMLAN device that receives and transmits messages and signals for window functionality. The DDM contains the driver door switch (DDS) which is integrated into the module. The DDS contains the driver, front passenger, RR and LR window and window lockout switches.
• Passenger front door module (PDM)--GMLAN device that receives and transmits messages and signals for window functionality. The PDM contains the front passenger door switch (PDS) which is integrated into the PDM. The PDS contains the front passenger window switch.
• Left rear power window switch--Provides switched voltage and ground window switch signals to the left rear window motor for left rear passenger window operation
• Right rear power window switch--Provides switched voltage and ground window switch signals to the right rear window motor for right passenger window operation
• Left front power window motor--Contains position sensors and a module that receives signals from the DDM and provides a status signal to the DDM
• Right front power window motor--Contains position sensors and a module that receives signals from the PDM and provides a status signal to the PDM
• Left rear power window motor--Contains position sensors and a module that receives signals from the left rear power window switch
• Right rear power window motor--Contains position sensors and a module that receives signals from the right rear power window switch
• DRIVER DR MOD fuse (15-amp)
• PDM fuse (15-amp)
• PWR WNDW Circuit Breaker (25-amp) -- front
• LT/REAR/WNDW fuse (15-amp) -- rear
• REAR/WNDW fuse (15-amp) -- rear


Power Window Operation
The driver and front passenger doors are equipped with power window motors that contains its own module. Each power window motor receives a hot at all times battery supply voltage and constant ground source. When the right front passenger window switch on the DDS is activated to the up or down position, the DDM will interpret the signal and send a GMLAN serial data message to the PDM. Upon receipt of the message, the PDM will send a signal to the front passenger window motor module on the GMLIN serial data circuit. The window motor module will then supply battery voltage and ground to the window motor to drive the window motor to the up or down position.
The DDM communicates via the GMLAN serial data circuit with the body control module (BCM) to control the rear window functions from the driver master window switch. The BCM is hard wired to each rear power window switch with circuits for window up, window down, and an enable circuit. The rear window switches contain internal logic that when supplied with voltage from the BCM over the enable circuit will driver the appropriate window in the direction commanded.
The rear power window switches are supplied with battery voltage from individual right and left WNDW fuses located in the rear fuse block. When a rear power window switch is activated to the DOWN position, voltage is applied to the motor down circuit and the motor up circuit serves as the path to ground. The window motor will drive in the downward direction until the switch is released or the window has fully opened. When the window switch is activated to the UP position, voltage is applied to the motor up circuit and the motor down circuit serves as the path to ground. Ground for the left rear power window switch is supplied at G200 and the right rear power window switch receives ground at G201.

The power locks work the same .

After replacing the driver door switch (DDS) or passenger door switch (PDS), perform the programing procedure.

If you don't know any of what i posted your best bet , have a qualified repair shop check it out .

Whatever all those lights have in common is the cause of your problem! Switch? Fuse? Wiring harness?

You will either have to replace the drivers master window switch or you have bad window motors. If you can still control the windows on the driver switch then the safety switch is bad and you need to replace the whole master switch. If the windows still can't be controlled by the front, then the motors may be bad.

if 3 windows are not working then 95% chance it is the main window switch. first check relays and fuses.

It may be that it is not on the track properly or your power window motor is old and tierd and can take the window down but it doesn't have the juice in it any more to bring it back up. replace the motor and it will work. This problem happened to me in my '76 ford ltd and a new motor fixed it.

Do you have global opening whre you can hold down your "Unlock" button on your remote and have all the windows open?

Look for water getting into a connector, usually in the wiring in the drivers door. Remove the door trim panel & check the connectors. report back

usually if the front are working then the rear should be too. check your light bulbs. if you tow stuff, check the wiring harness on the hitch.

COULD BE EITHER CHECK THE FUSES FIRST THEN TEST THE MOTOR SWITCH SEE IF YOU GET VOLTAGE WHEN YOU PUSH THE BUTTON

Hello and thank you for using FixYa!

Most likely your window regulator cable broke. That is why the glass can not be controlled. You will need to remove it and inspect it to verify.

Thanks Jay!

did you replace the left rear switch? if so you need to replace the master switch. which is the drivers front.