Question about Chrysler Sebring

Open Question

Crank shaft tone wheel flex plate damaged - Sebring Chrysler Cars & Trucks

Posted by Anonymous on

Ad

2 Related Answers

Anonymous

  • 99 Answers

SOURCE: 1996 geo prizm has broken rod on cyclinder #4

no you got to take the head off

Posted on Jan 24, 2009


Ainur-666

Rebel K

  • 44 Answers

SOURCE: crank shaft moves fore and aft under engine load

Yes, this is a problem which is very common to this particular vehicle. It is slightly an expensive fix, yet if you could get the bearing fixed instead of replacing it, you'd save some cash!

Posted on Aug 07, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Was told that the trans or engine would need to come out to replace the flywheel in my 98 continental.? Is that correct? Saw another suggestion from Colin Strickland here on fixya. See added details.


flywheel teeth get damaged in 3 places for 6 cyl or 4 for v8 If the teeth are damaged then the fix is a replacement ring gear
now if the car is automatic it will not have a flywheel as the torque convertor does that job
there is a flex plate bolted instead to the crank shaft and inturn bolted to the torque converter
They are kown to develope faults and crack off at the crank shaft so that they become warped ( not allowing full pinion engagement) or dreak off altogether and not turn the crank at all
The thrust bearings on the crank generally do not fail as they run in oil all the time so disregard that suggestion( if the thrust bearing was to fall ot completely , the added movement is 1/8 " and the pinion would still engage a good ring gear)
Now the teeth have to be replaced so for an automatic it is a new flex plate ( box out )
for a manual it is flywheel off and a new ring gear fitted to the flywheel ( box out )
check the pitch of the teeth of the new starter
the movement of the pinion can be checked by an accredited auto electrician and adjusted by the encentric pivot pin in the solenoid fork
So what ever happens the box has to come out for the repair

Mar 25, 2018 | Cars & Trucks

2 Answers

What causes damage flywheel on bmw is it common fault


-you mean broken teeth...? If so possibly crank the engine while it's still running.


Good Luck


Mai

Jan 07, 2016 | BMW X3 Series Cars & Trucks

1 Answer

How do you align the flex plate on 2004 Dodge Stratus 2.7?


i believe that the flex plate only goes on one way and it sends a signal to the crank sensor that is what all of the slots on the flex plate are for the crank sensor is located on the outside of the transmission it has one bolt and a electrical wire connection unplug it and pull it out of the transmission be careful not to break it they some times are stuck but with a little movement left and right then pry it up with a screwdriver you could have damaged this during intstallation of the fly wheel because these go in the transmission and ride real close to the flexplate check and see if you have spark at the spark plugs if not i believe you may have damaged this good luck i hope this helps

Dec 07, 2013 | 2004 Dodge Stratus

1 Answer

2003 hyundai elantra low idle check engine lights two broken fly wheels


flywheels or flex plates ( manual or automatic)
flywheels will generally shatter the bell housing so It may be flex plates
They crack the center out from incorrect fitment of the washes at the crank shaft that makes them flex against the torque converter
generally it is the omission or the incorrect fitment of the large dish shaped washes or the flex plate not being turn around until all of the bolts screw all the way in finger tight
the units are make in thousands and last hundreds of thousands of miles so to have such a problem is lack of attention to detail on fitment or lack of trade skill in the fitting

Jan 20, 2018 | Hyundai Motor 2003 Elantra

1 Answer

What do code p1391 mean


P1391 means intermittent loss of CKP and CMP , these sensor are monitor when the engine cranking,or running,These can come from a damage flex plate for the cranksensor or damage tone wheel for the camsensor,to a failing cranksensor ,failing camshaft sensor, to even the harness intermittent connnection

Mar 12, 2012 | Cars & Trucks

2 Answers

WHAT DOSE THE CODE P0335 AND P0315 MEAN


CODE PO335 CRANKSHAFT POSITION SENSOR CIRCUIT. CODE PO315 - NO CRANKSHAFT POSITION SENSOR LEARNED. POSSIBLE CAUSES, CRANKSHAFT TONE WHEEL FLEX PLATE IS DAMAGED, TONE WHEEL PULSE RING MAY BE DAMAGED, ERRATIC CKP SENSOR SIGNALS WIRING CONNECTOR PROBLEM, CKP SENSOR HAS FAILED, PCM HAS FAILED.

Jul 01, 2011 | 2009 Chrysler Sebring

2 Answers

Codep0016 what does it mean?


P0016 Chrysler

Crankshaft -camshaft timing misalignment bank 1 sensor 1
- The pcm detects that the camshaft position is out of phase with the crankshaft position

Probable Cause[s]

  1. Engine oil dirty or contaminated /Incorrect engine viscosity
  2. Open or short circuit condition
  3. Camshaft 1/1 position solenoid, camshaft phaser ,camshaft1/1 position sensor
  4. Crankshaft position sensor ,crankshaft,tone wheel or flex plate
  5. Camshaft,tone wheel or pulse ring

Mar 13, 2011 | 2006 Dodge Caravan

1 Answer

Were is the abs sensor mounted on the rear of an


The ABS sensor are attached to the brake backing plate assemblies and tone rings are pressed on the axle shaft. Use care when removing axle shaft as NOT to damage the tone wheel or the sensor.

In the ZJ-Secc-5-Brakes (page 25) can find information about the sysrtem and sensors location.

I really hope helped with this; remember rated this help. Good luck.

Nov 30, 2009 | 1996 Jeep Grand Cherokee

1 Answer

What is the metal plate called that goes on the crankshaft where the timing belt is?


It has many names - 1. Crank Position Sensor Blade, 2. Crank Position Sensor Tone Wheel, 3. Crank Position Blade, 4. Crank Position Tone Wheel, 5. Crank Position Sensor Position Wheel, etc.

Nov 03, 2009 | 1994 Hyundai Sonata

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...