Question about 2004 Toyota ECHO

1 Answer

Need to replace clutch on 2004 toyota echo

I never done a front whell drive ,i could used good advice an picture or name of good manuel for dummies? tks

Posted by Anonymous on


1 Answer


  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 200 questions.

  • Toyota Expert
  • 276 Answers

I done one a few weeks ago. all you have to do is mark all your wires and attachments. remove the whole front suspension you have to have the right tools it's a fairly big job but take your time and you should be able to do it. make sure you replace your throw out bearing also

Posted on Aug 26, 2018


5 Related Answers


SOURCE: 2000 toyota echo, wheel bearings

I found this site to be very helpful with this job:

Posted on Sep 23, 2008



  • 1077 Answers

SOURCE: how to replace timing belt in 1990 toyota camry

It would be to hard to tell and show you over the computer.
The best way for you is to buy a Chilton manual for your car at the autoparts store. The book runs about $20
This book is a do-it-yourself bible. It will show you everything you need to know on how to do maintenance and repair on your vehicle.

Posted on Apr 08, 2009


  • 223 Answers

SOURCE: Replacing only the driver side mirror w/o replacing the assembly.

You should be able to just replace the mirror as long as its flat.

Posted on Jun 15, 2009


  • 634 Answers

SOURCE: Does anyone know how to replace an Echo Rear Bumper?

if u slide under the car and look there are plastic pop pins u pull these out and then move any plastic shields and look carefully the are a few bolts that go through bumper fascia u remove these and slide fascia straight back and then reverse to install, align carefully and reconnect

Posted on Jul 09, 2009


Justin Case

  • 1498 Answers

SOURCE: i can't get the belt back on my 2004 toyota echo


Serpentine Belt. There is a trick.

Click here for a procedure I wrote. It's quick and you don't need a prybar.

You will no doubt find it very helpful.

Best regards


Posted on Dec 04, 2009

Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

When I switch my 2005 envoy xl into all whell drive and then drive, when I get out it smells like burnt rubber. It does not smell like that when in 2wd. What could it be?

You can't use 4 wheel on dry or even wet pavement. It must be snow dirt gravel or mud. Pavement will just burn up your tires because the front Axel pulls faster than the rear. When you have good grip there is a friction fight between front and rear tires.

Dec 22, 2014 | 2005 GMC Envoy Xl

1 Answer

My 1999 range rover its an all whell drive what could happen if i disconnect the front drive shaft and use it as two well drive

I have had to do this on a couple of occasions due to front propshaft failure, the system thinks the front wheels are spinning and therefore pushes all power to the rear, this should cause no long term affects.

Feb 10, 2014 | 1999 Land Rover Range Rover

1 Answer

Want to know Torque setting for Front Axle Hub Nut

front wheel drive then a good pull on a decent bar is sufficient ,if older rear wheel drive vehicle then this is different as they are taper bearings and sholud not be over tightened ,just pinch up till whell doesnt wobble when grasped at the top and bottom

May 20, 2011 | Volkswagen Quantum Cars & Trucks

1 Answer

Need firing order for 96 4.3 vortec 4 whell drive s10 blazer

The firing order is 1,6,5,4,3,2.The number 1 plug is on the drivers side front.Hope this helps.Good luck.

Nov 06, 2010 | 1996 Chevrolet S-10 Pickup

1 Answer

The 4 wheel drive with a turn knob control will

take the four wheel drive actuator out of the front differential let it hang while still plugged in and have somebody watch and see if it retracts when the 4 whell drive is switched from 2 to 4 whell drive. If not then accuator is probably bad.

Jan 05, 2010 | 2007 Chevrolet Silverado 2500HD

1 Answer

Will not go into 4-whell drive. Floor shift seems to work OK but 4-whell light does not come on and it does not lock the hubs

You most likely have a defective part in the front differential. Typically, the transfer case is O.K Repair is not to costly.

Dec 11, 2009 | 1995 Chevrolet Suburban

1 Answer

Radio manuel for "94 Plymouth Voyager

Try "google images" and see if you can find picture of face on your radio, that may help jog memory. Unless you have model or at least name on front, and anything else it says.

Aug 05, 2009 | 1994 Plymouth Voyager

1 Answer

Ford escord 1998

It would appear that the front caliper assy (namely the piston) is in a near frozen or seized position. This mostly happens to the front passenger side (the side nearest the curb while driving) due to the puddles in the road.

My advice to you is to replace the caliper assembly and bleed the braking system as soon as possible as it is a safety hazard. You may find that your new brake pads on the affected side will have prematurely already been worn down a bit also!

Good Luck!

Jan 16, 2009 | 1997 Ford Escort

1 Answer

Truck shakes in four whell drive

I think you may have a problem with the drive shaft angle being to steep, check with a drive line shop for the correct angle, the make special wedge shaped shims to correct this problem.

Oct 04, 2008 | 1992 Ford F150 SuperCab

Not finding what you are looking for?
2004 Toyota ECHO Logo

Related Topics:

273 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides