Question about 1994 Mercury Sable

1 Answer

Need to remove starter and cant get to it

What do i need to remove to get the starter out

Posted by momofsyco5kd on


1 Answer


If you own enough of the right tools, you can get to it

You my have to raise or lower the engine or lower
one side of the sub frame for clearance,but I doubt it.

Posted on Sep 11, 2012


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Having to replace my starter motor after it burnt out following it staying in the start position - how do I go about removing the old one to put in the new

Sandra, the procedure for removing and replacing starter varies from vehicle year,make, model and engine. Re POST year, make, model,engine and complete question so we, here at fixya can answer your question effectively.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How To Replace Your Starter AutoZone Car Care
Car starter see how to replace auto starters with this step by step guide
How to Replace Car Starter Motor

Aug 21, 2016 | Cars & Trucks

1 Answer

Does the exhaust manifold need to be removed to replace the starter

well i cant remember but if you can see the starter you should know whats in the way for you to do the job smoothly

Jun 25, 2014 | 2005 BMW Z4

1 Answer

Starter on my 95 harley dyna wide glide clicks battery seems to be good

have a load test done on the battery as experience shows that seems good will not handle the load of a starter motor

Dec 01, 2013 | Pontiac Sunfire Cars & Trucks

1 Answer


good luck to change the starter you gotta take off the front axle its so dumb u cant get to it unless you do that. good luck.. my advice take it into a mechanic. u really do have to remove the whole front axle

Sep 01, 2012 | 2000 Acura 3.5RL

1 Answer

I am ignorant and cant find the starter

Don't feel that way Brian. Not everyday you need to locate the starter on a car.
Even the trade guys need to look for stuff on cars. It's easier for us when we have the information.

Anyway, getting on to your problem.
It is at the front of the engine down low beside the oil pan.
It is even hard to get a look at on a hoist from below. Lots of stuff in the way on this one.
Here is a diagram.

To replace will need some time and patience.
  1. Disconnect the battery negative cable.
  2. Raise and suitably support the vehicle.
  3. Remove the front lower air deflector.
  4. Remove the starter solenoid S terminal nut.
  5. Remove the starter solenoid S terminal wiring harness connector at the starter motor.
  6. Remove the starter solenoid BAT terminal nut.
  7. Remove the starter solenoid BAT terminal wiring harness connector at the starter motor.
  8. Remove the torque converter cover.
  9. Remove the starter bolts. Remove the shims, if necessary.
  10. Remove the starter motor.
  11. Reverse procedure to reinstall.
There you are. I hope the job goes well.
Ask me if you need further help with this.


Jan 23, 2011 | 2000 Oldsmobile Intrigue

2 Answers

I have a 1997 acura tl 3.2 that needs a starter! Well I cant get the starter out of the car its to tight! What do I need to do to change the starter? Can I remove something to give me room to pull the...

breaker bars will add leverage you might have to remove some of the intake stuff, and break cleaner which will loosen the bolts

just for starters

Jun 02, 2010 | 1997 Acura TL Series

3 Answers


The starter is found under front end.. Near where the moter meets the trani - you will see the flywheel (a big round gear) the starter connects to the flywheel to turn the motor..

Disconnect the battery..
Disconnect wires from starter..
Should be 2 bolts that hold the starter in - remove them..

The starter goes in only one way so you cant mess it up..

Rate well ;o)

Jul 22, 2009 | 1994 Toyota Camry

1 Answer

Daewoo Nubira Starter Motor Refit.

changed a clutch on one of these a few weeks ago and cant remember what i done ,old timers i think ?? not sure but its from below with a rear support bracket ,and a inlet manifold stay bar ,,,3/8 drive socket set with a knuckle and 3 long extension bars to get to top inside bolt as well i think ?? honestly cant remember ,i work on all makes and cant remember every one

Apr 14, 2009 | 1999 Daewoo Nubira

1 Answer

Porsche 928s 1985 starter motor removal

Sorry you will have to remove the swaybar

Mar 03, 2009 | 1985 Porsche 928

1 Answer

Where is located the starter?

On your 91 Lexus Ls400.
The starter motor is located :
Rear of the Engine. Under the Intake Manifold.
You can see unless you remove the intake.
Becuase for replace the Starter Motor on your car
You will need to REMOVE the INTAKE MANIFOLD.
To get axces to the Starter Motor.

The Aproximate time for Remove and Install the starter is:
5.1 Hours, labor.
I'm a Mechanic.
I hope this help on your question.
Thank you for use fixya..

Sep 05, 2008 | 1991 Lexus LS 400

Not finding what you are looking for?
1994 Mercury Sable Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

gerry bissi

Level 3 Expert

4388 Answers


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides