Saturn no 1st, 2nd, 3rd, or 5th gear

05 Chrysler pacifica is a 4 speed automatic, next time buy a car with a 5 speed automatic

If the Linkage is not damaged, you are going to need to pull the Transmission out.

The part that went bad is called the SYNCRO's

Sounds like one of the levers inside the transmission is either broken or otherwise disengaged. Remove the shifter to see if you can see any obvious reason.

time to put a new tranny in that jet most of the time it costs to much to repair it then replace it i have done may tranny rebuilds and replacements to me i would just tell you to replace it at least you will get a better warrentee and stuff

This does sound more like a bad cable. You'll need to find the shift tower on the transmission and have someone move the shift so you can see if it moves when trying to put it in the bottom gears.

Hi:
The shift pattern is pretty much the same on all 5 speed cars. The top row is the odd numbers, 1-3-5
the bottom row is 2-4-Reverse. The center position is neutral

Here is the key: The shifter is slightly spring-loaded to the center position. If you hold in the clutch pedal and pull the shifter to neutral, and let go of it, it will automatically be lined up in the position, that if you pushed it forward , it would go to 3rd gear, and if you pulled it back, it would go into 4th gear.
This way, to start driving, you start out in neutral, grab the shifter lightly, and push it first to the left, then forward. This is first gear, where you start out. when you want to shift to second, push in the clutch, and keeping left pressure on the shifter, pull all the way back . Here is the easy part, 2nd to 3rd. When you are ready, push in the clutch, and just push the gear shift forward , till it hits neutral, and is spring loaded to the middle. Then you just push it straight forward to 3rd, then next shift, straight back to 4th.
Last gear, 5th: push forward to the neutral row, then Push to the right till it lines up ,and forward to the 5th gear. Reverse should only be shifted into from a dead stop. Find neutral, push the shifter all the way right, then pull back towards you. Hope this helps.
Practice a bunch in the driveway!

The cables attach near the back of the transaxle. You may be able to see them under the brake lines. You will probably need to remove the air intake from the throttle body to get good access.

no hydralic fluid in the resvoir look for the resvoir on the fire wall of the drivers side if its empty well fill it back up lol not sure if the sw1 has this but ive had too fix this problem before

J1/S1 Found in: Integra XSI/RSI (DA6) Type: Cable 1st: 3.230 2nd: 2.105 3rd: 1.458 4th: 1.107 5th: 0.848 R: 3.000 FD: 4.400 Y1 Found in: CRX/Civic (optional LSD) Type: Cable 1st: 3.166 2nd: 2.052 3rd: 1.416 4th: 1.103 5th: 0.870 R: 3.000 FD: 4.266 YS1 Found in: Integra 92-93 XSI/RSI (DA6, DA9) Type: Cable 1st: 3.307 2nd: 2.105 3rd: 1.458 4th: 1.107 5th: 0.880 R: 3.000 FD: 4.400 S80 Found in: Integra Type R 98+ (LSD) Type: Hydraulic 1st: 3.230 2nd: 2.105 3rd: 1.458 4th: 1.034 5th: 0.787 R: 3.000 FD: 4.785 S80/Y80 Found in: JDM SiR-G (optional LSD) Type: Hydraulic 1st: 3.230 2nd: 1.900 3rd: 1.360 4th: 1.034 5th: 0.787 R: 3.000 FD: 4.400 Y21/Y80/S80/S4C Found in: JDM 96-97 Integra R(LSD) JDM Civic R [EK9](LSD) JDM Civic SiR [EK4, EG6] JDM CR-X DEL SOL SIR (EG2)(optional LSD) USDM DEL SOL VTEC (EG2)(OPTIONAL LSD) Type: Hydraulic 1st: 3.230 2nd: 2.105 3rd: 1.458 4th: 1.107 5th: 0.848 R: 3.000 FD: 4.400

check shift fork adjustment. make sure you bleed the slave cylinder.also check shift cable adjustment.