Question about 1998 Chevrolet C2500

Open Question

Where is clutch slave cylinder located on 98 chevy cheyenne?

Posted by Anonymous on

Ad

5 Related Answers

hank5899

hank5899

  • 151 Answers

SOURCE: 97 chevy cavalier 2.2l 5sp clutch problem

get the hyd clutch system assembly complete and pre-bleed from the dealer

Posted on Sep 07, 2008

Ad
motor1258

Mike Butler

  • 6674 Answers

SOURCE: 1994 chevy camaro 3.4manual 5 speed

You may want to read bleeding instruction at this link, it may shed some light.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800b886d

Posted on Jan 31, 2009

Ad

Nicolo Carlo Parazo

  • 2187 Answers

SOURCE: clutch slave cylinder replacement or repair -

You will have to replace the rubber and the piston like mechanism to get this done. If you found an assembly replacement for the entire clutch slave, the better. The leaks may be caused by faulty rubber or valve on the piston but this can be caused by the linings of the cylinder becoming rough due to wear and tear.

Posted on Aug 20, 2009

Anonymous

  • 33 Answers

SOURCE: clutch pedal stays 2 the floor on a hydralic

Did you bleed the system? When you replace the the master and/or slave cylinder you have to bleed the system just as you would with brakes. There is a bleed screw on the slave cylinder. Open the bleed screw, have a helper depress and hold the clutch pedal down.Tighten the bleed screw, then release clutch. Repeat this procedure until you have removed all air from the system and the clutch pedal is firm. Keep an eye on the fluid level to avoid sucking air into the system. If you have done this, remember there is a possibility that the master or slave cylinder is defective.

Posted on Sep 06, 2009

Martin Bergin

  • 133 Answers

SOURCE: 1992 Chevy Silverado - Clutch Slave Cylinder broke

JB weld will not work get it welded by a pro with the proper hi frequency welder otherwise you will have to replace the box ,and yes get a new cylinder ,hope you get sorted

Posted on Mar 03, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1987 chevy Cheyenne 1 ton dually w/standard transmission clutch quit working not sure if it be slave cylinder or something else?


Does the pedal go to the floor?? If so it is the master and the slave, they are replace as one unit of repair. If the pedal is very stiff but doesn't go to the floor you have a failed clutch.

Jun 01, 2016 | Cars & Trucks

1 Answer

Where is the slave cylinder on a 98 dodge avenger 2.0l. Internal or external?


Should be mounted on the side of the transmission. Follow the line down from the master cylinder.

Jun 09, 2013 | Cars & Trucks

1 Answer

I have a 1994 Chevy C1500 how would i find a leak for the clutch


The clutch master cylinder is located on the firewall in front of the clutch pedal and has a solid plastic line (hose) that runs directly to the clutch slave cylinder which is located inside the bell housing of the transmission. Unless it has rubbed against something and developed a leak, which is very unlikely, the leak will be at the slave cylinder and drip from the front edge of the bell housing where it meets the engine. This is a common problem with older Chevy trucks and the best fix is to replace the entire hydraulic system with a pre-assembled unit available at most parts suppliers. These units come with the master cylinder, hydraulic line and slave cylinder with a new release bearing (throw-out bearing) and are pre-bled and full of fluid. Replacing just the slave cylinder is a major job and bleeding these systems have been known to drive people crazy. Replacing ALL of it aint much more work and saves your sanity not to mention all those dirty words.12_28_2012_1_54_36_am.png

Dec 28, 2012 | Cars & Trucks

1 Answer

Where is the slave cylinder on 91 gmc sierra


I had a 92 Chevy Cavalier which had the hydraulic clutch system like yours. I had intended to flush and purge the hydraulic clutch system at the same time I flushed and purged the brake system. I traced the hydraulic lines from the master cylinder into the front of the transmission where the clutch is located. This is the most likely place to look for the slave. I didn't find a way to bleed the lines with the transmission still in and the Hanes manual I had was unhelpful. The dealer told me it was a "special job" that had to be done in a shop.

Oct 04, 2012 | Cars & Trucks

1 Answer

Where is the clutch auto adjustment located at on a 98 manual Volkswagen jetta?


you most likely have a hydraulic clutch, which the clutch master cylinder is located on the firewall on the driverside close to your drivers side windsheild.it takes brake fluid to fill dot brake fluid will fill it properly. however if your slave cylinder on the transmission is leaking,this will require a replacement of the clutch slave cylinder. look for leakage under passenger side,,just under or below passenger side seat onto ground. recommend if you replace the clutch slave cylinder,you also replace clutch master cylinder located on the drivers side firewall at wind sheild.look under the car while someone pumps the clutch in and out,if you see brake fluid leaking under car onto ground or inside onto carpet at brake pedal,you have a bad clutch master cylinder. recommend you replace both slave cylinder and clutch master cylinder. this will save you lots of time and headaches. thank you for choosing fixya.com

Sep 24, 2011 | 1998 Volkswagen Jetta

1 Answer

I have a 1992 Chevy Cheyenne and I am trying to bleed the clutch. I believe I have gotten all the air our\t of it but the clutch still has no pressure the slave and master cylinder are new and there are no...


Start by getting in and working the clutch till your leg feels like its going to fall off.Then hold on floor and have another person open the bleeder.Try this several times...It should build pressure. Hope this helps

Jun 11, 2011 | 1992 Chevrolet C1500

2 Answers

Clutch fluid leaking inside of trans housing on a 98 s10


do you mean a manual model ?? is the slave cylinder inside the bell housing ??if so renew it

Dec 27, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

Replaced clutch but pedal will not move down at all now on 98 chevy 1/2 ton 2wd


Sounds like the release bearing is in backwards! No check valve. If the peddle was pushed, it would pop the slave cylinder piston. 2/ The clutch disc could be in backwards too! Either way, you will need to pull the tranny! Sorry! Frankster016

Oct 22, 2008 | 1998 Chevrolet K1500

Not finding what you are looking for?
1998 Chevrolet C2500 Logo

Related Topics:

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

john h

Level 3 Expert

23515 Answers

Joe Taylor
Joe Taylor

Level 3 Expert

2228 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...