Question about Cars & Trucks
The battery started running out and died suddenly. Now using spare, I am trying to fix the other, but manual says take it to a LDV dealer for re-code!!! (guess when they wrote it they did't know LDV where broke and going to the cleaners!!) Can anyone help sorting my problem and is a bit frustrating. Help!
I know from experience that you cannot really re synch these fobs on the LDV Maxus vans.
What actually is the fault is an onboard component on the pcb has failed and we normally just replace that with a new one..the fob will be tested for operation and sent back. OR its the Relay in the ESA unit - under the left hand front glovebox on the bulkhead - black with cables going into it. We have those relays (soldered to the pcb) we can supply those or do the work for you. The fob connects to that ESA and the unit then fires the relays to open/close the doors. Sometimes that unit is installed upside down which causes water (condensation) to enter the box and have fun with your electrics.
The fob is SYNCHED to this unit via coding we can use your old fob to clone to a new fob and that will work with the ESA and the vehicle.
We have the parts on this link Items for sale from remobilise ltd
Here is a link to how to program the fob to the vehicle via the programmer - NOTE how you MUST have a working fob to program another (text at the start of the video... LDV Maxus flv
We can fix most problems on the LDV Maxus that occur with faults to do with the Central locking/fobs/ESA/ETACS - three relays are in the ESA and they control ONLY the central locking - two more relays are in the ETACS unit (behind the ashtray) and they control the fogs and intermittant wipers.
Any help or info needed please contact [email protected]
or tel 01792 896404.
We are based in Swansea UK.
Posted on Dec 02, 2014
I answered this in a previous link:
Posted on Mar 15, 2017
SOURCE: porsche key fob
If the key had gone faulty, the key code must be re programmed on the vehicle computer. This can be done only using a PIWIS tool, available at the dealer or at a qualified Porche garage.
Try also the following reset:
turn ignition on,
remove the transponder from the column
push any button on the fob within 6 seconds.
This procedure will reset the key synchronizing again with the vehicle computer.
Posted on Sep 13, 2008
SOURCE: renault key fob doesnt work
I have a clio II, 2001, i have the same problem and i fixed it.
Don't know if will work for you but here it goes:
1 - no key in ingnition
2 - press the unlock button in console off the car for about 10 seconds(dont let go)
3 - it should work the central doors one time and then 2 times( hear)
4 - press the remote a few times until it starts working
It worked for me hope the same for you.
Please tell me if it worked and pass the message.
Posted on Sep 15, 2009
SOURCE: honda ridgeline key fob program
If it is a factory keyless system than you do need it done by the dealer, but if it is an after market system then reply back with manufacture and model.
Posted on Oct 17, 2009
sounds like it could be the pressure control valve on the fuel pump not an expensive repair. the pressure drops in the line over night. try priming the filter whilst the engine is being cranked. the control valve is held on by 3 torx screws on the end of the pump.
Posted on Feb 26, 2010
Tips for a great answer:
Mar 10, 2018 | Cars & Trucks
Mar 10, 2018 | Cars & Trucks
Nov 03, 2017 | Cars & Trucks
Oct 30, 2017 | Cars & Trucks
Mar 01, 2014 | 2011 Dodge Charger
Feb 02, 2013 | Cars & Trucks
Jan 29, 2012 | Cars & Trucks
3,027 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: