At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Re: where is the crankshaft position sensor; how to...
Both are located under the timing cover.you will have to remove the timing sproket to get to the CrankshaftPS. be careful to notice how you removed it. the sproket have to be reinstalled exactly the same way you removed it.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
A lot of things have been replaced ... but there was no mention of checking any fuses or relays.
As an example ... if the fuel pump relay is bad then the car will crank over but not start
There is a switch/sensor located at you break pedal, when you hit the breaks this has a small pin that make positive contact telling your break lights to come on. It may be broken or stuck, check it.
Also check all the bulbs on your car, breaks and blinkers etc...
P1335, No Crankshaft Position Sensor Signal - Engine Running. ... 91 1991 ToyotaCelica GTS Engine Mount Right 2.2L 4 Cyl Genuine. ... 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001 . ... Powered by a 2.2-liter engine, the Celica now had ST and GT trim models. ... in 1986 and a 2.0-liter ...
31 mins ago - It is not behind pully nor in dist all videos show - Toyota Cars & Trucks question. ... Change a crankshaft position sensor on a 2000 eclipse.
toyota camry crankshaft sensor 99 camry crankshaftcamshaft position codes i got a problem with my 97 ... The car 96 toyota camry 2.2 liter 4 cyl. ... 1994 toyota camry 2.2L 257k miles Symptoms Car overheats Top radiator hose hot bottom cold ...
Jul 10, 2014 - The Toyota 5SFE motor is a four-cylinder, 2.2 liter, timing-belt-driven, double ..... Remove the lower timing belt cover with the crankshaft position sensor. ..... I've never, ever replaced the harmonic balancer on a 4cyl 5SFE.
Disconnect the negative battery cable from the battery. On vehicles equipped with an air bag, wait at least 90 seconds before proceeding.
Remove the front covers and the timing belt.
Remove the crankshaft timing belt sprocket.
WARNING When removing the front seal, be extremely careful not to damage the crankshaft.
Using a knife, cut off the oil seal lip.
Tape the end of a flat bladed tool to avoid damaging crankshaft. Pry out the oil seal using the taped end of the tool.
Inspect the oil seal riding surface on the crankshaft for signs of wear or damage.
To install:
Wipe the seal bore with a clean rag.
Apply multipurpose grease the lip of a new oil seal.
Drive the oil seal into place using tool SST 09309–37010 or an equivalent seal installer tool. Make sure the seal surface is flush with the oil pump case edge. Work from the front of the cover. Be extremely careful not to damage the seal.
Install the sprocket without disturbing the Woodruff key.
Install the timing belt and front covers.
Connect the negative battery cable to the battery.
its usually up next to oil filter or behind crankshaft pulley.if you have a 4 cylinder engine you have to move oil filter to get to it. if you got a v6 or v8 engine.remove pulley harmonic balancer.
THE FUEL PRESSURE TEST PORT IS ON THE METAL FUEL SUPPLY RAIL FOR THE FUEL INJECTORS, IT LOOKS LIKE A TIRE VALVE BUT METAL, U NEED A TEST GUAGE, THEY ARE CHEAP FROM KRAGEN OR AURTZONE, THIS SURE SOUNDS LIKE A PRESSURE ISSUE, U WILL HAVE TO WATCH THE PRESSURE WHEN THE PROBLEM OCCURS AT 70MPH
Replace the A/C compressor revolution sensor, bolted to the side of the compressor, unless the connector was inadvertantly left unconnected. This is the only reason the AC light will blink.
location of camshaft position sensor
thanks
×