Need wiring harnass specs for stock stereo in 95 toyota corolla

I would suggest you spice the wires back to stock harness by male and female connections and tape over them with black tape then get a stereo install kit that includes a wiring harness ( cost about $20 maybe or less) for the year of truck you have... it will plug right to your stock harness ...never just cut stock stereo wires from stock plug it will be more of a headache than you think trust me I've installed all my own stereo system been there done that... good luck

all radios work if not OEM and bricked (code secret lost)
they sell an adaptor for your car that fits the stock harness, at
all autostores and even walfart.

buy that ,read the instructions, easy peasy city,

the phyiscal , i refuse to guess, only electronics.

At
www.reliable-store.com
get complete guide on whether to repair or not, service it, and how to repair etc, along with wiring diagrams, electrical diagrams, torque specs, error codes, everything.

1999 Toyota Corolla Car Radio Stereo Audio Wiring Diagram
Car Radio Constant 12v+ Wire: Blue/Yellow
Car Radio Switched 12v+ Wire: Gray
Car Radio Ground Wire: Brown
Car Radio Illumination Wire: Green
Car Stereo Dimmer Wire: N/A
Car Stereo Antenna Trigger: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): Pink
Left Front Speaker Negative Wire (-): Violet
Right Front Speaker Positive Wire (+): Light Green
Right Front Speaker Negative Wire (-): Blue
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Black
Left Rear Speaker Negative Wire (-): Yellow
Right Rear Speaker Positive Wire (+): Red
Right Rear Speaker Negative Wire (-): White

Radio Constant 12V+ Wire: Blue/Yellow
Radio Switched 12V+ Wire: Gray
Radio Ground Wire: Brown
Radio Illumination Wire: Green
Left Front Speaker Wire (+): Pink
Left Front Speaker Wire (-): Purple
Right Front Speaker Wire (+): Purple
Right Front Speaker Wire (-): Light Green
Left Rear Speaker Wire (+): Black
Left Rear Speaker Wire (-): Yellow
Right Rear Speaker Wire (+): Red
Right Rear Speaker Wire (-): White

I would get a stereo installation kit for your car from Auto Zone or a local car audio store. It will have the surround for the new stereo to fit where the old one was and a harness that you can wire the new stereo to and the harness will have a plug to match the stock radio plug.

There are 3 things you need to purchase for this install. 1) The factory spec install kit. 2) The factory spec additional wiring harness. 3) Antenna adapter.

Find the easied way to remove the plastic cowling around the radio and ac controls. Usually you can locate screws helping to retain the plastic dash parts. Be careful not to break the plastic dash by taking your time and looking over and over the part ofr connection hardware. Once you have located and removed all/if any screws, carefully pry out on the piece you are removing. There are often metal clips on the back of the piece that also help to retain the dash. Once that is removed, unbolt/unclip the factory stereo and slowly pull it out of the dash. Remove the factory harness from the backside of the factory stereo. DO NOT CUT THE HARNESS!! The wiring harness you have purchased is designed to plug and play into the factory harness. All you hae to do is color match the Kenwoods harness with the one you purchased. When wiring the two harnesses together use connectors **** a **** connectors, crimp connectors so forth and so on. If there is wiring you will not be using, take some electrical tape and tape the bare wire. We don't want a short. Once you are sure and have doubled checked that all the wiring is secure and matched, reverse the order of disassembly.

The plastic install kit should replace the factory radio size difference. Just remember to take the metal sleeve tha came with the kenwood and install it into the plastic install kit via the instructions provided. Slide the Aftermarket stereo into the sleeve you just installed. Then you are ready to make all the needed connections. Before you reassemble everything make sure to do a test run with your stereo. If all is well reassemble and jam on.

Sure. Glad to provide assistance.

89 Corolla radio wiring colours:

Power- Solid GREY -
from the 7.5 amp RADIO fuse

Backup power - BLUE w/YELLOW tracer
from the 10 amp DOME fuse

RF speaker - LIGHT GREEN and BLUE
LF speaker - PINK and VIOLET
RR speaker - RED and WHITE
LR speaker - BLACK and YELLOW
Ground/Earth - BROWN

The graciousness of a FixYa rating would be greatly appreciated.

Hi, if you mean your antenna has a motor to make it go up, you can use the blue wire for that. Does the installation instruction say the red wire is battery or ignition/accessory? Many cars do not have the correct wiring harness for aftermarket head units. This is why you were told to run a wire to the fuse panel. That is the correct way to professionally install a wire that did not come in the harness. There are usually spare slots in the panel. You can even add a fuse, if you want a real pro installation. uou just have to connect to the correct leg of the panel that is for accessory power (which is usually corresponds to the red aftermarket wire).

This maybe due to the fact that all manufactured wiring harnesses installed in the corolla are standard looms, you will probably find that you do not have rear speakers installed, however the wires are located beneath the speaker grill by the parcel shelf. the standard corolla stereo only uses front speakers,but the loom has the ability to connect 4 speakers.most manufacturers always fit 1 standard loom as it is cheaper to install a full loom than make variations for different specs and models.check your stereo to see if it is used with 2 or 4 speakers. regards neil